Introduction
This manual provides detailed instructions for the DAKEFPV H743 Flight Controller and 12S 120A Electronic Speed Controller (ESC) Stack. Designed for high-performance FPV drones, this stack offers robust control and power delivery. Please read this manual thoroughly before installation and operation to ensure proper functionality and safety.

Setup and Installation
Package Contents (Option 1 - H743 120A 30x30 STACK)

- DAKEFPV H743 Flight Controller x 1
- DAKEFPV BLS 120A 4 in 1 ESC x 1
- 35V 1000uF Low ESR Capacitor x 1
- M3 Nylon Nut x 5
- M3 silicone O Ring x 5
- M3*8mm Silicone Grommets (for FC) x 1
- M3*8.1mm Silicone Grommets (for ESC) x 1
- SH 1.0mm 25mm-length 8pin Cable (for FC-ESC connection) x 1
- SH 1.0mm 75mm-length 8pin Cable* x 1
- M3*30mm Inner-hexagon Screws x 5
- GPS 6-pin cable, Analog VTX 6-pin cable, dual-camera 6-pin cable x 1
- XT60 Power Cable (70mm) x 1
*When the ESC tail faces the drone's front, use this cable for the flight controller.
Physical Dimensions

The flight controller and ESC are designed for a 30.5x30.5mm mounting pattern. The flight controller measures 36x36mm, and the ESC measures 45.4x42.8mm. The total stack height is approximately 15.8mm.
Important Stack Installation Note

When installing your stack, adhere to the standard mounting method. If you opt for an inverted manner, be extra careful about the space between the frame, the FC, and the ESC. It is critical to swap the silicon pads when changing the positions of the FC and the ESC. This step is vital to prevent any contact between the FC's USB interface and the ESC, which could lead to a short circuit. Any damage resulting from improper installation of this nature is not covered under the Warranty.
Wiring Diagram

Note 1: In order to prevent the stack from being burnt out by voltage spikes on powering up, it is strongly recommended to use the Low ESR capacitor included in the package.
Note 2: The FC and ESC can also be connected via direct soldering. Refer to the diagram for soldering pad definitions.
Cable Connections
DJI O3 Air Unit / RunCam Link / Caddx Vista Air Unit

Use the 6-pin cable that comes with the O3 Air Unit for connection. The DJI Air Unit plug is completely compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, requiring no wire modification.
SBUS Receiver Connection

If you are also using the DJI Air Unit (O3/Link/Vista/Air Unit V1), you will need to disconnect the SBUS signal wire from the Air Unit harness. Failure to do so will prevent the SBUS receiver from being properly recognized by the flight controller. You can use tweezers to pick out the SBUS wire from the 6-pin harness connector (or directly cut this wire) and insulate the exposed part of the wire carefully.
Importance notice for ELRS receiver: We recommend connecting the ELRS receiver's TX and RX to the T2 and R2 pads on the flight controller. However, when using the DJI Air Unit simultaneously, some ELRS receivers may not be recognized properly by the flight controller. If you encounter this issue, you need to disconnect the SBUS signal wire from the Air Unit harness. Do NOT connect this wire to assure the external SBUS receiver works properly!
Operating Instructions
LED Light Bar Pads

The LED pads at the corners of the flight controller allow you to decorate your aircraft with your favorite LED light strips. A single press of the BOOT button lets you switch between different lighting modes. A long press of the BOOT button switches to this mode, and short presses of the BOOT button let you toggle between various preset light effects.
Battery Capacity Indicator

On the side of the flight controller, you will find a 4-level battery capacity indicator. As soon as you connect the battery, you can instantly see the battery level, saving you the hassle of needing to put on glasses to check the battery status.
Firmware Support
The DAKEFPV H743 Flight Controller supports popular FPV firmwares including INAV, Betaflight, and Ardupilot, offering flexibility for various flight preferences and applications.
Maintenance
To ensure the longevity and optimal performance of your DAKEFPV H743 stack, follow these maintenance guidelines:
- Regular Inspection: Periodically check all solder joints and connections for any signs of corrosion, damage, or loose contacts.
- Cleaning: Keep the boards clean from dust, dirt, and debris. Use a soft brush or compressed air. Avoid using liquids directly on the electronics.
- Proper Handling: Always handle the flight controller and ESC by their edges to avoid touching sensitive components. Use anti-static precautions when working with the electronics.
- Environmental Protection: Protect the stack from moisture, extreme temperatures, and direct sunlight. Consider conformal coating for added protection in humid or wet environments.
- Firmware Updates: Keep your flight controller firmware updated to the latest stable version to benefit from performance improvements and bug fixes.
Important: Any damage resulting from improper installation, handling, or modification of this nature is not covered under the Warranty.
Troubleshooting
- No Power/Intermittent Power:
- Ensure all power connections are secure and correctly soldered.
- Verify battery voltage and XT60 connector integrity.
- Check if the Low ESR capacitor is properly installed to prevent voltage spikes.
- SBUS Receiver Not Recognized (with DJI Air Unit):
- As per the setup instructions, disconnect the SBUS signal wire from the DJI Air Unit harness. This is crucial for some ELRS receivers to function correctly when used simultaneously with the DJI Air Unit.
- Ensure the ELRS receiver's TX and RX are connected to the T2 and R2 pads on the flight controller.
- Motor Issues (No Spin/Incorrect Direction):
- Check motor wiring to the ESC for correct connections (M1-M4).
- Verify motor direction in your flight controller software (Betaflight/INAV/Ardupilot) and adjust if necessary.
- Ensure ESC calibration is performed correctly.
- Flight Controller Not Connecting to PC:
- Try a different USB cable and USB port on your computer.
- Install the necessary drivers for your flight controller (DFU drivers).
- Ensure the flight controller is powered correctly.
- Unstable Flight/Drifting:
- Calibrate the accelerometer and gyroscope in your flight controller software.
- Check for vibrations in the drone frame; soft-mounting the FC/ESC can help.
- Ensure PID tuning is appropriate for your drone setup.
Specifications
DAKEFPV H743 Flight Controller

| Feature | Detail |
|---|---|
| Main Control Unit (MCU) | STM32H743 |
| Gyroscope | ICM42688P (Dual Gyro) |
| USB Interface Type | Type-C |
| Barometer | Built-in |
| OSD Chip | AT7456E |
| Bluetooth BLE | No |
| WiFi | Not supported |
| DJI Air Unit Connection | Supports 6-pin plug-in and direct soldering. Fully compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1 without wire modification. |
| Flash Memory | 16MB |
| UART Ports | 8 groups |
| BEC Output | 12V 3A, 5V 3A (Dual independent) |
| Motor Support | 8 motors + 4 servos (for X8, Y6, fixed-wing aircraft) |
| Mounting Hole | 30.5 x 30.5 mm (4mm holes) |
| Dimensions | 36 x 36 x 8 mm |
| Weight | 10.5g |
| Certification | CE |
DAKEFPV 12S 120A 4 in 1 ESC

| Feature | Detail |
|---|---|
| Firmware | BLHeli_S / BlueJay |
| Battery Input | 3-12S LiPo |
| Continuous Current | 120A x 4 |
| Maximum Current | 280A for 10 seconds |
| Built-in TVS Diode | Yes |
| External Capacitor | 1000uF high-frequency low-resistance electrolytic capacitor (included) |
| ESC Protocol | Dshot300/Dshot600/PWM/Bi-directional Dshot |
| Input Voltage | 3-12S LiPo |
| Output Voltage | VBAT |
| Current Meter | Yes (Scale=400, Offset=0) |
| Mounting Hole | 30.5 x 30.5 mm (4mm holes) |
| Dimensions | 45.4 x 42.8 x 6.5 mm |
| Weight | 23.5g |
User Tips
- Always double-check all wiring connections before applying power to prevent damage to components.
- Utilize the provided Low ESR capacitor to protect against voltage spikes, especially with high-power setups.
- When mounting the stack, ensure adequate clearance between the flight controller and ESC, particularly if using an inverted configuration, to avoid short circuits.
- For optimal performance and compatibility, regularly check for and apply the latest stable firmware updates for Betaflight, INAV, or Ardupilot.
- Take advantage of the built-in battery capacity indicator for quick battery status checks during field use.
Warranty and Support
DAKEFPV products are manufactured to high standards. In the unlikely event of a manufacturing defect, please contact your retailer or DAKEFPV customer support for assistance. Please note that damage caused by improper installation, misuse, modification, or accidents is not covered under warranty. Always refer to the detailed instructions in this manual for correct usage.