DAKEFPV F722 Flight Control FC & 4in1 ESC Stack

Contents

DAKEFPV F722 Flight Control FC & 4-in-1 ESC Stack User Manual

Model: F722 Flight Control FC & 4in1 ESC Stack

Brand: DAKEFPV

1. Introduction

The DAKEFPV F722 Flight Control (FC) and 4-in-1 Electronic Speed Controller (ESC) stack is a high-performance solution designed for FPV racing drones and other multi-rotor or fixed-wing aircraft. Featuring an STM32F722 main control chip, ICM42688P gyroscope, and robust power delivery, this stack offers excellent flight stability and control. It supports a wide voltage input range (3-12S) and comes in various ESC current ratings (100A/120A) to suit different power requirements. This manual provides essential information for proper installation, configuration, and operation of your DAKEFPV F722 stack.

DAKEFPV F722 Flight Controller with STM32F722 MCU and BetaFlight, iNAV, ArduPilot logos
DAKEFPV F722 Flight Controller featuring STM32F722 MCU, compatible with BetaFlight, iNAV, and ArduPilot firmware.

2. Features

  • Main Control Unit: STM32F722 (FC)
  • Gyroscope: ICM42688P
  • ESC Current: Available in 100A and 120A 4-in-1 configurations
  • Input Voltage: 3-12S LiPo (FC), 3-8S LiPo (ESC)
  • Mounting: 30.5 x 30.5mm (M4 holes)
  • Onboard Barometer: For real-time altitude sensing
  • Black Box: Built-in 16MB high-speed FLASH for flight data recording
  • Power Output: 12V 3A + 5V 3A Dual-channel BEC
  • Motor Support: Supports up to 8 motors and 4 servos, suitable for X8/Y6/fixed-wing aircraft
  • Connectivity: 8 UART serial ports, DJI Air Unit direct plug interface (compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1), external GPS module support (5.0V powered)
  • Capacitor: 35V 1000uF Low ESR Capacitor included
  • OSD Chip: AT7456E
  • USB Interface: Type-C
  • Battery Indicator: 4-level battery capacity indicator on FC
  • LED Control: Dedicated pads for LED light bars with preset light effects via BOOT button
  • ESC Firmware: BLHeli_S / BLUEJay
  • ESC/Motor Protocol: Dshot300/Dshot600/PWM/Bi-directional Dshot
Summary of DAKEFPV F722 BLS 120A Stack features
Key features of the DAKEFPV F722 BLS 120A Stack, highlighting its capabilities.

3. Package Contents

The DAKEFPV F722 stack is available in different configurations. Please verify your specific package contents upon receipt.

Option 1 - DAKEFPV F722 120A 30x30 STACK

  • DAKEFPV F722 Flight Controller x 1
  • DAKEFPV BLS 120A 4 in 1 ESC x 1
  • 35V 1000uF Low ESR Capacitor x 1
  • M3 Nylon Nut x 5
  • M3 Silicone O Ring x 5
  • M3*8mm Silicone Grommets (for FC) x 1
  • M3*8.1mm Silicone Grommets (for ESC) x 1
  • SH 1.0mm 25mm-length 8pin Cable (for FC-ESC connection) x 1
  • SH 1.0mm 75mm-length 8pin Cable x 1
  • M3*30mm Inner-hexagon Screws x 5
  • GPS 6-pin cable, Analog VTX 6pin cable, dual-camera 6pin cable x 1
  • XT60 Power Cable (70mm) x 1

Note: When the ESC tail faces the drone's front, use the 25mm-length 8pin cable for FC and ESC connection; both ends plug interchangeably.

Package contents for DAKEFPV F722 120A 30x30 STACK
Contents of the DAKEFPV F722 120A 30x30 Stack package.

Option 2 - DAKEFPV F722 120A 30x30 FC (Flight Controller Only)

  • DAKEFPV F722 Flight Controller x 1
  • Silicone Grommets (random colors) x 8, hexagon screws x 5, hexagon nuts x 5, silicone rings x 3
  • FC12-pin to ESC 8-pin cable, LED/buzzer 4-pin cable x 1
  • GPS 6-pin cable, analog VTX 6-pin cable, dual-camera 6-pin cable x 1, receiver 4-pin cable
Package contents for DAKEFPV F722 120A 30x30 FC (Flight Controller only)
Contents of the DAKEFPV F722 120A 30x30 Flight Controller only package.

Option 3 - DAKEFPV 12S 120A 4 in 1 ESC (ESC Only)

  • DAKEFPV 12S 120A 4 in 1 ESC x 1
  • 35V 1000uF Low ESR Capacitor (Buy 12S ESC Send 63V1000uF Capacitor)
  • FC 12-pin to ESC 8-pin cable (for connecting FC to ESC)
  • XT60 x 1
Package contents for DAKEFPV 12S 120A 4 in 1 ESC (ESC only)
Contents of the DAKEFPV 12S 120A 4-in-1 ESC only package.

4. Specifications

4.1. DAKE F722 30x30 Flight Controller

FeatureSpecification
Main Control Unit (MCU)STM32F722
GyroscopeICM42688P
USB Interface TypeType-C
BarometerBuilt-in
OSD ChipAT7456E
Bluetooth BLENone
WiFiNot supported
DJI Air Unit Connection6-pin socket direct plug, solder wire connection
6-pin DJI Air Unit Direct Plug SocketSupported (Fully compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no wiring changes needed)
FLASH (Black Box)16MB Flash
AmmeterSupported
Input Voltage3-12S LiPo Battery
UART Serial Ports8 groups
Buzzer PadSupported (BZ+, BZ- pads connect to 5V active buzzer)
BOOT ButtonPress and hold while powering to force DFU mode for firmware flashing
RSSI PadSupported (Located on top front)
SmartPort / F.PortNot supported
Supported FC FirmwareBetaFlight (default), ArduPilot
Firmware Target NameDAKEFPVF722
Mounting Hole Position30.5 x 30.5mm (M4 hole diameter)
Dimensions36 x 36 x 8 mm
Weight10.5g

4.2. DAKE 12S 120A 4-in-1 ESC

FeatureSpecification
FirmwareBLHeli_S / BLUEJay
Input Voltage3-8S LiPo Battery
Max Current120A x 4 (Continuous), 280A (Peak for 10s)
Built-in TVS DiodeYes
External Capacitor1000uF Low ESR Capacitor (included)
ESC/Motor ProtocolDshot300/Dshot600/PWM/Bi-directional Dshot
Output VoltageVBAT
AmmeterSupported (Scale=400, Offset=0)
Power TelemetryNot supported
Mounting Hole Position30.5 x 30.5mm (M4 hole diameter)
Dimensions45.4 x 42.8 x 6.5 mm
Weight23.5g
Dimensions of the F722 Flight Controller and 4-in-1 ESC
Physical dimensions of the F722 Flight Controller and 4-in-1 ESC, showing 30.5x30.5mm mounting and stack height.

5. Setup & Installation

5.1. Stack Assembly

The F722 Flight Controller and 4-in-1 ESC are designed to be stacked. Ensure proper orientation and use the provided silicone grommets and screws for mounting.

Video demonstrating the assembly of the F722 Flight Controller and 4-in-1 ESC stack.

Important Stack Installation Note:

When installing your stack, adhere to the standard mounting method. The orientation of the gyro and motor sequence can be adjusted through settings. If you opt for an inverted manner, be extra careful about the space between the frame, the FC, and the ESC. It's critical to swap the silicon pads when changing the positions of the FC and the ESC, as illustrated below. This step is vital to prevent any contact between the FC's USB interface and the ESC, which could lead to a short circuit. Please be aware that any damage resulting from improper installation of this nature is not covered under the Warranty.

Diagram showing important stack installation notes, including spacing and silicon pad placement
Diagram illustrating critical considerations for stack installation, including maintaining adequate space and correct silicon pad placement to prevent short circuits.

5.2. Wiring Diagram

Refer to the following diagrams for connecting your flight controller to motors, receivers, and other peripherals.

Wiring diagram for F722 Flight Controller and 4-in-1 ESC to motors and peripherals
Comprehensive wiring diagram showing connections between the F722 FC, 4-in-1 ESC, motors, and other components like GPS, ELRS receiver, and SBUS receiver.

Note 1: In order to prevent the stack from being burnt out by voltage spikes on powering up, it is strongly recommended to use the Low ESR capacitor included in the package.

Note 2: The FC and ESC can also be connected via direct soldering. Soldering pads definition is as follows:

BLS 120A 4-in-1 ESC layout with motor connections and capacitor pin holes
Layout of the BLS 120A 4-in-1 ESC, indicating motor connections (M1-M4) and capacitor soldering points (BAT+, GND).

5.3. Receiver Connections

The F722 FC supports various receiver types. Pay close attention to SBUS and ELRS receiver connections.

Importance notice for SBUS receiver: When using an SBUS receiver, the SBUS signal wire of the receiver must be connected to the SBUS pad on the front side of the flight controller (this pad internally uses UART2).

Importance notice for ELRS receiver: We recommend connecting the ELRS receiver's TX and RX to the T2 and R2 pads on the flight controller. However, when using the DJI Air Unit simultaneously, some ELRS receivers may not be recognized properly by the flight controller. If you encounter this issue, you need to disconnect the SBUS signal wire from the Air Unit harness. For some ELRS receivers, it is necessary to disconnect this wire in order to function properly!

SBUS and ELRS receiver connection details, including a note on disconnecting SBUS wire for DJI Air Unit V1
Detailed instructions for connecting SBUS and ELRS receivers, with a specific warning about DJI Air Unit V1 compatibility requiring SBUS wire disconnection.

5.4. DJI Air Unit Connections

The F722 FC is designed for direct plug-in compatibility with DJI Air Units.

Cable Connection vs DJI O3 Air Unit: Use the 6-pin cable that comes with the O3 Air Unit.

Cable Connection vs RunCam Link/Caddx Vista Air Unit: Use the 6-pin cable that comes with the H743 stack (refer to accessory No.11 in the package section).

Diagrams for connecting DJI O3 Air Unit and RunCam Link/Caddx Vista Air Unit to the F722 Flight Controller
Visual guide for connecting different DJI Air Unit versions (O3, RunCam Link/Caddx Vista) to the F722 Flight Controller.

6. Operating Instructions

6.1. Battery Capacity Indicator

The flight controller features a 4-level battery capacity indicator. Once the battery is connected, you can instantly see the battery level, eliminating the need for an external LiPo checker.

F722 Flight Controller with 4-level battery capacity indicator
The F722 Flight Controller's integrated 4-level battery capacity indicator for quick battery status checks.

6.2. LED Light Bar Control

The LED pads at the corners of the flight controller allow you to decorate your aircraft with your favorite LED light strips. A single press of the BOOT button lets you switch between different lighting modes. A long press of the BOOT button switches to the onboard LED light effect control mode, and short presses of the BOOT button let you toggle between various preset light effects.

F722 Flight Controller showing LED light bar pads and control via BOOT button
Illustration of the LED light bar pads on the F722 FC and how to control lighting effects using the BOOT button.

6.3. Firmware Flashing (DFU Mode)

To enter DFU (Device Firmware Upgrade) mode for firmware flashing (e.g., BetaFlight, ArduPilot), press and hold the BOOT button while powering the flight controller. This is used for updating firmware or troubleshooting issues.

7. Maintenance

  • Keep the flight controller and ESC clean and free from dust and debris.
  • Avoid exposing the components to moisture or extreme temperatures.
  • Regularly inspect solder joints and connections for any signs of damage or corrosion.
  • Ensure all screws are tightened appropriately, but do not overtighten to avoid damaging the PCB.
  • Periodically check for firmware updates for both the FC (BetaFlight/ArduPilot) and ESC (BLHeli_S/BLUEJay) to ensure optimal performance and access to new features.

8. Troubleshooting

  • No Power: Check battery connection, XT60 cable, and ensure the included Low ESR capacitor is properly installed to prevent voltage spikes.
  • No Signal from Receiver: Verify receiver wiring (SBUS/ELRS) and ensure the correct UART is selected in your flight controller software. For ELRS with DJI Air Unit V1, ensure the SBUS signal wire is disconnected from the Air Unit harness if issues arise.
  • Motors Not Spinning: Check ESC connections to motors, ESC firmware, and motor protocols (Dshot300/600). Ensure ESCs are armed correctly.
  • Flight Instability: Verify gyro orientation in flight controller software. Ensure the stack is securely mounted and free from vibrations.
  • DFU Mode Issues: Ensure the BOOT button is pressed *before* applying power to the FC. Try a different USB cable or port.
  • Black Box Data Not Recording: Ensure the black box feature is enabled in your flight controller software.

9. User Tips

  • Always double-check your wiring before applying power to prevent damage.
  • Use heat shrink tubing or electrical tape to insulate exposed wires and solder joints.
  • Start with default PID settings in BetaFlight/ArduPilot and tune gradually for optimal flight performance.
  • Consider using a smoke stopper during initial power-up after assembly to prevent damage from short circuits.
  • For advanced users, explore the full capabilities of BetaFlight/ArduPilot firmware for custom configurations and flight modes.

10. Warranty & Support

This product is covered by a standard manufacturer's warranty against defects in materials and workmanship. Damage caused by improper installation, misuse, or unauthorized modifications is not covered. For technical support, firmware updates, or warranty claims, please contact DAKEFPV customer service or refer to their official website for resources.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.