Beitian BN-180, BE-220, BE-250, BE-280, BE-880

Contents

Beitian Multi-GNSS Receiver Module User Manual

Models: BN-180, BE-220, BE-250, BE-280, BE-880

1. Introduction

This manual provides detailed instructions for the Beitian series of Multi-GNSS Receiver Modules, including models BN-180, BE-220, BE-250, BE-280, and BE-880. These modules are designed for integration with Arduino, flight control systems, and drones, offering reliable global navigation satellite system capabilities. Please read this manual thoroughly before installation and operation to ensure optimal performance and safety.

Overview of Beitian GPS modules: BN-180, BE-220, BE-250, BE-280, BE-880

Figure 1: Various Beitian Multi-GNSS Receiver Modules

Video 1: Product overview of Beitian GPS modules.

2. Specifications

The Beitian Multi-GNSS Receiver Modules offer robust performance for various applications. Key specifications are detailed below:

Feature Description
ChipM10 050
FrequencyGPS L1 C/A, QZSS L1 C/A/S, BDS B1I/B1C, Galileo E1B/C, SBAS L1 C/A (WAAS, EGNOS, MSAS, GAGAN)
Operation ModeGPS+BDS+GALILEO+SBAS+QZSS
Sensitivity (Track)-166dBm
Sensitivity (Re-arrest)-160dBm
Sensitivity (Cold Start)-148dBm
Sensitivity (Hot Start)-160dBm
Horizontal Accuracy1.5m CEP 2D RMS SBAS Auxiliary (for open sky)
Speed Accuracy0.05m/s
Dynamic Heading Angle Accuracy0.3 deg
1PPS Time AccuracyRMS 30ns, 99% 60ns
Start Time (Cold Start)27s
Start Time (Hot Start)1s
Start Time (Assisted Start)1s
Baud Rate4800bps - 921600bps (default 38400bps)
Output LevelTTL level
Output ProtocolNMEA, UBX
NMEA SentencesRMC, VTG, GGA, GSA, GSV, GLL
Update Frequency0.25Hz - 18Hz (default 1Hz)
Second PulseConfigurable from 0.25Hz to 10MHz (default period 1s, high level last for 100ms)
Max Altitude80,000m
Max Speed< 500m/s
Max Gravitational Acceleration< 4g
VoltageDC 3.6V - 5.5V (Typical 5.0V)
CurrentNormal 50mA/5.0V
Operation Temperature-40 °C ~ +85°C

Module Comparison

Comparison table for Beitian BE Series GPS modules including connector type, size, flash memory, and compass availability.

Figure 2: BE Series GPS Module Comparison

3. Setup and Installation

Proper connection of the GPS module is crucial for its functionality. Refer to the specific pinout diagrams and tables for your module model.

General Pinout Information

Most modules share common pins like GND (Ground), TX (Transmit), RX (Receive), and VCC (Power Supply). Some models may include additional pins like 1PPS (1 Pulse Per Second), BOOT, SDA, and SCL for advanced features or compass functionality.

  • GND: Ground connection.
  • TX (Transmit): Serial Data Output from the GPS module. Connect to the RX pin of your microcontroller (e.g., Arduino, flight controller).
  • RX (Receive): Serial Data Input to the GPS module. Connect to the TX pin of your microcontroller.
  • VCC: Power supply input. Typically DC 3.6V - 5.5V, with 5.0V being common.
  • 1PPS (1 Pulse Per Second): Output signal indicating a precise one-second interval, useful for time synchronization when 3D fixed.
  • BOOT: Boot pin (N.C. - No Connection for normal operation).
  • SDA (Serial Data Line): I2C data line for compass functionality (e.g., BE-880).
  • SCL (Serial Clock Line): I2C clock line for compass functionality (e.g., BE-880).

Specific Module Pinouts

Beitian BE-180 GPS module pinout diagram showing GND, TX, RX, VCC pins and their descriptions.

Figure 3: BE-180 Pinout and Description

Beitian BE-220 GPS module pinout diagram showing GND, TX, RX, VCC pins and their descriptions.

Figure 4: BE-220 Pinout and Description

Beitian BE-250 GNSS module pinout diagram showing GND, TX, RX, VCC pins and their descriptions.

Figure 5: BE-250 Pinout and Description

Beitian BE-280 GPS module pinout diagram showing 1PPS, GND, TX, RX, VCC, BOOT pins and their descriptions.

Figure 6: BE-280 Pinout and Description

Beitian BE-880 GPS module pinout diagram showing SDA, GND, TX, RX, VCC, SCL pins and their descriptions.

Figure 7: BE-880 Pinout and Description

4. Operation

Once correctly wired and powered, the GPS module will begin acquiring satellite signals. The operational status can be monitored via the indicator LEDs:

  • TX LED (Blue): This LED flashes when data is being output from the module. A steady flash indicates active data transmission.
  • PPS LED (Red): This LED indicates the GPS fix status. It will not be bright when the GPS has not achieved a fix. Once a position fix is established, the LED will flash, typically once per second (1PPS).

The module outputs data using NMEA and UBX protocols. The default baud rate is 38400bps, and the update frequency is 1Hz, though these are configurable. For detailed configuration, refer to the specific documentation for the M10 050 chip or your flight controller's GPS setup guide.

5. Maintenance

Beitian GPS modules are designed for durability and require minimal maintenance. To ensure longevity and reliable performance:

  • Keep Dry: Protect the module from moisture and humidity. Water exposure can damage internal components.
  • Cleanliness: Keep the module free from dust and debris. If cleaning is necessary, use a soft, dry brush or a lint-free cloth. Avoid using liquids or harsh chemicals.
  • Physical Protection: Handle the module with care to prevent physical impact or bending of pins. Ensure it is securely mounted in its intended application.
  • Temperature: Operate the module within its specified temperature range (-40 °C to +85°C) to prevent damage.

6. Troubleshooting

If you encounter issues with your Beitian GPS module, consider the following troubleshooting steps:

  • No Power/No LEDs:
    • Verify that the VCC and GND connections are correct and that the power supply is within the 3.6V-5.5V range.
    • Check for any loose wires or poor solder joints.
  • No Data Output (Blue TX LED not flashing):
    • Ensure the TX pin of the GPS module is correctly connected to the RX pin of your microcontroller.
    • Confirm that the baud rate configured in your software matches the module's default (38400bps) or configured baud rate.
    • Check for any short circuits or breaks in the data lines.
  • No GPS Fix (Red PPS LED not flashing):
    • Ensure the module has a clear, unobstructed view of the sky. Indoor or obstructed environments can prevent satellite acquisition.
    • Allow sufficient time for a cold start (up to 27 seconds) or hot start (1 second) in an open area.
    • Verify that the module is receiving adequate power.
    • Check for strong electromagnetic interference from other electronic components.
  • Incorrect Position Data:
    • Ensure the module is mounted correctly and not experiencing excessive vibration or movement during initial fix.
    • For modules with a compass (e.g., BE-880), ensure it is calibrated and free from magnetic interference.

7. User Tips

While no specific user tips from reviews or Q&A are available, general best practices for GPS modules include:

  • Optimal Placement: For best performance, mount the GPS module with a clear view of the sky, away from other electronics that might cause interference.
  • Power Stability: Provide a stable and clean power supply to the module to avoid erratic behavior or signal loss.
  • Software Configuration: Utilize the appropriate libraries and configuration tools for your microcontroller (e.g., u-center for u-blox based modules) to fine-tune settings like baud rate, update frequency, and NMEA sentence output.
  • Antenna Orientation: Ensure the ceramic antenna faces upwards towards the sky for optimal signal reception.

8. Support

For further assistance or technical inquiries regarding your Beitian Multi-GNSS Receiver Module, please contact the seller, JoyCollector Store, through the platform where you made your purchase. Ensure you provide your product model and a detailed description of the issue for efficient support.

Manufacturer: Shenzhen DIY Maker Co., Limited

Email: wlzswza@gmail.com

© 2024 Beitian. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.