DIVEDEER D01 Series (6L-18L)

Contents

DIVEDEER Gas Water Heater Instruction Manual

Models: D01 Series (6L-18L) - Household Thermostat Gas Water Heater

1. Safety Information

Please read this manual carefully before installation and operation. Failure to follow these instructions could result in property damage, personal injury, or death. Keep this manual for future reference.

  • Ensure proper ventilation during operation.
  • Do not install the unit in a room without adequate ventilation.
  • Verify gas type (LPG or Natural Gas) matches your supply.
  • Always check for gas leaks after installation.
  • Keep flammable materials away from the water heater.
  • This appliance must be installed by a qualified professional in accordance with local codes and regulations.

2. Product Overview

The DIVEDEER D01 Series gas water heater is an instantaneous, oxygen-free water tank design, providing hot water on demand. It features a thermostat for stable water temperature and multiple safety protections.

Front view of DIVEDEER gas water heater with control knobs and digital display

Figure 1: Front view of the water heater with control panel.

Overview of DIVEDEER water heater models and features

Figure 2: Various capacities (6L-18L) and key features.

3. Setup and Installation

3.1 Unpacking

Carefully remove the water heater and all accessories from the packaging. Inspect for any damage during transit. Retain packaging for potential future transport.

3.2 Location Requirements

  • The unit is designed for outdoor installation or in a well-ventilated area. It is explicitly stated: "No installation in the room."
  • Ensure the installation area is protected from direct weather exposure if installed outdoors.
  • Maintain adequate clearance around the unit for ventilation and maintenance.

3.3 Mounting

Mount the water heater securely to a solid wall using appropriate fasteners. The back of the unit includes screw holes for mounting.

Back view of the water heater showing mounting holes

Figure 3: Back of the water heater with mounting points.

3.4 Exhaust Pipe Installation

The unit uses an Open & Force Flue Exhaust Type with Flue Automatic Gas Discharge. The exhaust pipe must be installed correctly to ensure safe operation.

Installation diagram for exhaust pipe, gas, and water connections

Figure 4: Exhaust pipe installation options (side or rear) and connection points. Total length of exhaust pipe should be within 3 meters with a maximum of 3 bends.

3.5 Water and Gas Connections

  • Water Connections: Connect the cold water inlet pipe and hot water outlet pipe. The water connection size is G1/2".
  • Gas Connection: Connect the gas inlet pipe. The rubber gas hose diameter is φ 0.79". Ensure the gas type (LPG or Natural Gas) matches the unit's specification.

3.6 Battery Installation

The ignition system requires 2pcs 1.5V D-Type Batteries (not included). Open the battery compartment, typically located at the bottom right of the unit, and insert the batteries with correct polarity.

Top-down view showing battery pack and control knobs

Figure 5: Location of the battery pack and control knobs.

4. Operating Instructions

4.1 Initial Startup

  1. Ensure all water and gas connections are secure and leak-free.
  2. Open the main gas supply valve.
  3. Open a hot water tap. The water heater will automatically ignite.
  4. The digital display will show the current water temperature.

4.2 Adjusting Water Temperature

The water heater features mechanical adjustment knobs for easy control:

  • Water Regulator: Adjusts the water flow rate.
  • Gas Regulator: Adjusts the gas flow to control flame intensity.
  • Winter/Summer Mode Selector: Optimizes heating for seasonal changes.
  • Fire Row Control: Allows for segmented control of the fire rows, automatically switching between high and low combustion to maintain constant water temperature even with increased water consumption.
Diagram of segmented fire row combustion technology

Figure 6: Segmented fire row combustion for stable temperature.

The thermostatic core regulates the temperature of the water flow, maintaining a stable water temperature with a variation as low as ±0.5°C.

Graph showing stable water temperature with 0.5°C difference

Figure 7: Comparison of temperature stability between thermostatic and non-thermostatic water heaters.

4.3 Digital Display

The unit features a digital display that shows the real-time water temperature. This allows for precise monitoring and adjustment.

5. Maintenance

Regular maintenance ensures optimal performance and longevity of your DIVEDEER water heater.

  • Exterior Cleaning: Wipe the exterior with a soft, damp cloth. Do not use abrasive cleaners.
  • Exhaust System: Periodically inspect the exhaust pipe and gas emission tube for any blockages or damage. Ensure the fan operates correctly before and after cleaning.
  • Water Tank: The pure copper water tank is designed for corrosion resistance and durability, contributing to healthy water quality. While it requires minimal internal maintenance, consult a professional for any concerns regarding water quality or tank performance.
  • Battery Replacement: Replace the D-type batteries when the ignition becomes weak or fails.
Diagram of pure copper water tank highlighting benefits

Figure 8: Pure copper water tank for quick heat and energy saving.

Detailed view of components: Copper Water Tank, D-Type Batteries, Gas Emission Tube, Back Screw Holes

Figure 9: Premium and exquisite details of the water heater components.

6. Troubleshooting

This section addresses common issues you might encounter. For problems not listed here, please contact customer support.

ProblemPossible CauseSolution
No hot water / Unit does not igniteNo gas supply, low water pressure, dead batteries, flame failure protection activated.Check gas supply, ensure adequate water pressure (min 0.015 MPA starting pressure), replace D-type batteries, check for flame failure.
Water temperature fluctuates (hot/cold)Inconsistent water flow, gas pressure issues, incorrect regulator settings.Adjust Water Regulator and Gas Regulator. Ensure stable water pressure. The unit is designed for ±0.5°C stability.
Low water flow / Insufficient hot waterLow water pressure, clogged water inlet filter, low water flow protection activated.Check main water supply pressure. Clean water inlet filter. Ensure suitable water pressure (0.02 MPA-0.8 MPA).
Unit makes unusual noiseFan issue, loose components, gas pressure irregularity.Inspect exhaust fan. Ensure all connections are tight. If noise persists, contact a professional.
Overheat protection activatedExcessive water temperature.Reduce gas flow or increase water flow. Allow unit to cool down before restarting.
Image depicting common water heater problems like long wait, insufficient flow, and temperature fluctuations

Figure 10: Common water heater issues addressed by this model's features.

6.1 Safety Features

The DIVEDEER water heater is equipped with multiple safety protections, including:

  • Overheat protection
  • Anti-frozen protection
  • Low water flow protection
  • Flame failure protection
  • Dry combustion protection
  • High water pressure protection
  • Safe and strong exhaust system
Diagram illustrating various safety protection features of the water heater

Figure 11: Comprehensive safety features for reliable operation.

7. Specifications

FeatureSpecification
Hot Water Output6L/min (1.6 GPM) to 18L/min (4.8 GPM)
Heater Output Power16KW to 36KW (varies by model capacity)
Gas TypeLPG (Liquid Petroleum Gas) or Natural Gas
Gas Pressure2800 Pa
Water Temperature Range10℃-60℃ (50 °F -140 °F)
Water ConnectionG1/2"
Rubber Gas Hose Diameterφ 0.79"
Suitable Water Pressure0.02 MPA-0.8 MPA
Starting Pressure0.015 MPA
Exhaust WayOpen & Force Flue Exhaust Type
Discharge WaysFlue Automatic Gas Discharge
Ignition2pcs 1.5V D-Type Batteries (not included)
Dimensions (approx. 10L model)Height: 55cm (21.7"), Width: 30cm (11.8"), Depth: 15cm (5.9")
Weight (approx.)8.0 kg
Front view of a 10L water heater with dimensions

Figure 12: Approximate dimensions for a 10L model.

8. User Tips

  • Easy Temperature Adjustment: The mechanical adjustment knobs are designed for user-friendly operation, making it easy for all users to set their desired water temperature.
  • Quiet Operation: The water heater operates at a low noise level, ensuring a quiet bathing experience. Noise levels can be as low as 50dB, comparable to a library sound.
  • Consistent Hot Water: Thanks to its efficient design and CPU intelligent temperature control technology, the unit provides hot water consistently, even in environments with low water pressure or high demand.
  • Healthy Bathing: The pure copper water tank contributes to cleaner water by inhibiting bacteria, promoting a healthier bathing experience.
Image emphasizing quiet operation of the water heater

Figure 13: Low noise operation for a peaceful environment.

Image highlighting low voltage start and suitability for various environments

Figure 14: Reliable performance even with low water pressure.

9. Warranty & Support

This DIVEDEER water heater comes with a National Warranty. For warranty claims, technical support, or service inquiries, please contact your retailer or the manufacturer's customer service department. Ensure you have your purchase details and model information readily available.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.