HITBOX HBM1200

Contents

HITBOX HBM1200 3-in-1 Welding Machine User Manual

Model: HBM1200

1. Introduction

Thank you for purchasing the HITBOX HBM1200 3-in-1 Welding Machine. This inverter welder combines MMA, Flux Cored MIG, and Lift TIG welding capabilities into a single, compact unit. Designed for both beginners and professionals, it offers stable arc performance, high efficiency, and robust safety features. Please read this manual carefully before operation to ensure proper use and to maintain the machine's longevity.

The HBM1200 is designed according to national and international standards, including GB/T15579-1, IEC60974, EN60974, AS60974, and UL60974, and conforms to EMC requirements. The design and manufacturing technology are patented.

2. Safety Precautions

Welding is inherently dangerous and can cause harm. Always prioritize your safety and the safety of others. Refer to the Operator Safety Guide for Compliance with Manufacturer Accident Prevention Requirements.

2.1 General Safety Guidelines

  • Professional Training: Only operate this machine after receiving professional training.
  • Protective Gear: Always wear a comfortable welding mask and appropriate protective clothing (gloves, long sleeves, etc.) to protect your eyes and body from arc rays, sparks, and heat.
  • Electrical Safety: Never touch charged areas with bare skin or wet gloves/clothing. Ensure you are insulated from the ground and workpiece. Always cut off power before maintenance or repair.
  • Ventilation: Welding produces smoke and gases that can be harmful. Work in a well-ventilated area, keeping your head away from fumes. Use exhaust or ventilation equipment to maintain a well-ventilated workspace.
  • Fire and Explosion: Welding sparks can cause fires. Ensure no combustible materials are nearby. Have fire extinguishers readily available and know how to use them. Container welding is strictly prohibited. Do not use for powder spray thawing.
  • High Temperature: Hot workpieces can cause severe burns. Do not touch hot workpieces with bare hands. Allow the torch to cool during continuous use.
  • Pacemakers: Magnetic fields can affect pacemakers. Individuals with pacemakers should stay away from the welding area and consult medical attention if necessary.
  • Moving Parts: Keep hands, hair, and tools away from moving parts like fans to prevent injury. Ensure all doors, panels, lids, and other protective devices are closed during operation.
  • Machine Failure: If the machine fails, seek professional help. If you encounter difficulties or do not understand the manual, contact your supplier's service center.

3. Main Parameters and Specifications

ParameterValue (HBM1200)
Input Voltage (V)AC 220V ± 15%, 50/60Hz
Rated Input Current (A)AC 220V 20A
Rated Input Capacity (KVA)4.5
Recommended Fuse Capacity (A)30
MMA Weld Current Range (A)10~120
MIG Welding Current Range (A)20~120
MIG Voltage Range (V)11~20
No-load Voltage (V)55
Wire Feeding Speed Range (m/min)1.5~16
Applicable Wire Diameter (mm)0.6/0.8 (Flux-cored) / 0.8/1.0mm (General)
Rated Duty Cycle35/40°C
Efficiency0.8
Factor0.75
Protection ClassIP21S
Insulation ClassF
Dimensions (L x W x H)12.59 x 9.45 x 5.9 inches (approx. 320 x 240 x 150 mm)
Weight9.92 lbs (approx. 4.5 kg)

3.1 Product Features

  • 3-in-1 Welding: Supports MMA (ARC), Flux Cored MIG, and Lift TIG welding modes.
  • Gasless MIG: Uses flux-cored wire, eliminating the need for external shielding gas.
  • Synergic Control: Automatic adjustment of wire feed speed to welding current for ease of use.
  • Digital Display: Large digital display for clear current and voltage readings.
  • Compact & Lightweight: Easy to carry and store, comparable to a shoebox in size.
  • Robust Protection: Features overvoltage, overcurrent, overheating, and overload protection.
  • Waterproof Switch: Enhanced durability and safety.
  • High Integration MCU: Ensures stable and reliable performance.
Internal view of the HBM1200 showing High Integration MCU and protection features like overvoltage, overcurrent, overheating, and overload protection.
Figure 1: Internal view highlighting safety and durability features.
Image showing the compact size and weight of the HBM1200 welding machine, comparing it to a men's shoebox.
Figure 2: Compact size and lightweight design of the HBM1200.

4. Panel Description

4.1 Front Panel

Diagram of the HBM1200 front panel with numbered labels for Digital Display, Rotary Selection Voltage, Welding Method, Rotary Selection Current, 2-Pin Socket, Connexion - and Connexion +.
Figure 3: Front Panel Layout
  1. MIG Torch Switch: Activates the MIG torch.
  2. MIG Torch Slot: Connection point for the MIG torch.
  3. Positive Output: Positive terminal for welding connections.
  4. Voltage Potentiometer: Adjusts welding voltage.
  5. MMA Flag: Indicator for MMA welding mode.
  6. Flux Cored Welding Wire 0.8 Indication: Indicator for 0.8mm flux cored wire.
  7. Function: Mode selection button.
  8. Flux Cored Welding Wire 1.0 Indication: Indicator for 1.0mm flux cored wire.
  9. TIG Indicator: Indicator for TIG welding mode.
  10. Abnormal Indication: Lights up to indicate an error or abnormal condition.
  11. Current Display: Digital display for welding current.
  12. Current (Wire) Potentiometer: Adjusts welding current or wire feed speed.

4.2 Back Panel

Diagram of the HBM1200 back panel with labels for Power Cable and Power Switch.
Figure 4: Back Panel Layout
  1. Power Cable Input: Connects the machine to the main power supply.
  2. Power Switch: Turns the machine ON/OFF.

5. Setup and Installation

Note: Always turn off the power switch before making any electrical connections. This machine has an IP21S protection rating, so avoid using it in the rain.

5.1 Connection of Input Cables

  1. Connect the main power cable to a rated input power supply. Grounding connections are required for safety.
  2. Ensure the primary cable is tightly connected to the correct socket to avoid oxidation.
  3. Verify the voltage value is within an acceptable range using a multimeter.

5.2 MMA (ARC) Installation

  1. The welding machine has two quick plugs. Plug the quick plug into the front panel and tighten it clockwise to ensure good contact.
  2. Plug the cable with the electrode holder into the "+" socket on the front panel and tighten it clockwise.
  3. Plug the cable with the work clamp into the "-" socket on the front panel and tighten it clockwise.
  4. DCEP (Direct Current Electrode Positive): Connect the electrode holder to the "+" output terminal and the work fixture to the "-" output terminal.
  5. DCEN (Direct Current Electrode Negative): Connect the electrode holder to the "-" output and the work fixture to the "+" output.
  6. Choose the connection method based on workpiece and electrode application. Incorrect connection can lead to unstable arc, splashing, and electrode adhesion.
  7. If secondary cables are long, use a larger cross-section cable to reduce voltage drop.

5.3 MIG (Flux Cored) Installation

  1. Connect the main power cable to the rated input power supply.
  2. Plug the quick plug on the MIG torch into the "-" socket on the front panel and tighten it clockwise.
  3. Plug the cable with the work clamp into the "+" socket on the front panel and tighten it clockwise.
  4. Open the wire feeder compartment. Install the wire spool onto the rotating shaft, ensuring the groove dimensions on the drive roller match the wire diameter.
  5. Feed the wire through the mechanism and into the torch. Press the wire snap button to feed the wire out of the torch head.
Image showing the wire feeder compartment of the HBM1200, indicating where to apply 2 lbs .030 inch and .039 inch flux core wire.
Figure 5: Wire Feeder Compartment for Flux Cored Wire.

5.4 Lift TIG Installation

  1. Connect the main power cable to the rated input power supply.
  2. Plug the quick plug on the TIG torch into the "-" socket on the front panel and tighten it clockwise.
  3. Plug the cable with the work clamp into the "+" socket on the front panel and tighten it clockwise.
  4. Connect the TIG torch to a flow regulator on a gas cylinder with appropriate tubing (TIG torch and gas cylinder are not included and require separate purchase).
Diagram illustrating the setup for MIG+Flux core, Lift TIG, and ARC welding modes with the HBM1200 machine.
Figure 6: Welding Mode Setup Diagrams (MIG+Flux core, Lift TIG, ARC).

For a visual guide on connections and setup, please refer to the product video:

Video 1: HBM1200 Setup and Welding Demonstration.

6. Operation

6.1 Power On and Mode Selection

  1. After installation, turn on the air switch on the back panel. The power LED will light up, and the fan will start.
  2. Use the mode selection button (Function) on the front panel to switch between MMA, MIG, and TIG modes.

6.2 MMA (ARC) Welding

  1. Switch to MMA mode.
  2. Adjust the welding current using the current control knob based on the workpiece thickness and electrode diameter.
  3. Recommended Current Settings (approximate):
    • φ2.5 electrode: 70-100A
    • φ3.2 electrode: 110-160A
    • φ4.0 electrode: 170-220A
    • φ5.0 electrode: 230-280A
  4. Perform spot welding or flat welding as needed.

6.3 MIG (Flux Cored) Welding

  1. Switch to MIG mode.
  2. If using shielding gas (for gas MIG, not flux cored), open the cylinder valve and turn the gas check switch to "gas check" position. Adjust the flow regulator for appropriate gas flow.
  3. Adjust the inductance control knob: counter-clockwise for lower inductance and harder arcs; clockwise for higher inductance and softer arcs.
  4. Select appropriate welding voltage and current using the respective control knobs.
  5. After the arc stops, the gas supply (if used) is cut off.

6.4 Lift TIG Welding

  1. Switch to TIG mode.
  2. Adjust the welding current using the current control knob.
  3. Perform welding, ensuring proper technique for Lift TIG.

6.5 Welding Programs and Parameters

Welding current and voltage significantly impact stability, quality, and productivity. Optimal settings depend on electrode diameter, metal transfer method, and production requirements.

6.5.1 Current in Short-Circuit Transition

Electrode φ (mm)Applicable Current (A)Optimum Current (A)
0.850~12070~100
1.070~18080~120
1.280~350100~200
1.6140~500140~350

6.5.2 Type I Butt Weld Parameters

Diagram illustrating Type I butt weld with dimensions g and 1.
Figure 7: Type I Butt Weld Diagram
Plate Thickness t (mm)Gap g (mm)Electrode φ mmWelding Current (A)Welding Voltage (V)Welding Speed (cm/min)Gas Flow (l/min)Layer
1.201.070-8017-1845-55101
1.601.080-10018-1945-5510-151
2.00-0.51.0100-11019-2040-5510-151
2.30.5-1.01.0 or 1.2110-13019-2050-5510-151
3.21.0-1.21.0 or 1.2130-15019-2140-5010-151
4.51.2-1.51.2150-17021-2340-5010-151

6.5.3 Flat Angle Welding Parameters

Diagram illustrating flat angle welding with dimensions.
Figure 8: Flat Angle Weld Diagram
Plate Thickness t (mm)Corn Size I (mm)Electrode φ mmWelding Current (A)Welding Voltage (V)Welding Speed (cm/min)Gas Flow (l/min)
1.22.5-3.01.070-10018-1950-6010-15
1.62.5-3.01.0-1.290-12018-2050-6010-15
2.03.0-3.51.0-1.2100-13019-2050-6010-20
2.32.5-3.01.0-1.2120-14019-2150-6010-20
3.23.0-4.01.0-1.2130-17019-2145-5510-20
4.54.0-4.51.2190-23022-2445-5510-20

6.5.4 Fillet Weld Parameters in Vertical Position

Diagram illustrating fillet weld in vertical position with dimensions.
Figure 9: Fillet Weld Diagram
Plate Thickness t (mm)Corn Size I (mm)Electrode φ mmWelding Current (A)Welding Voltage (V)Welding Speed (cm/min)Gas Flow (l/min)
1.22.5-3.01.070-10018-1950-6010-15
1.62.5-3.01.0-1.290-12018-2050-6010-15
2.03.0-3.51.0-1.2100-13019-2050-6010-20
2.33.0-3.51.0-1.2120-14019-2150-6010-20
3.23.0-4.01.0-1.2130-17022-2245-5510-20
4.54.0-4.51.2200-25023-2645-5510-20

6.5.5 Lap Welding Parameters (MAG)

Diagram illustrating lap welding with dimensions.
Figure 10: Lap Welding Diagram

Material: Carbon Steel
Gas: Ar+CO2 mixture (10 to 15 l/min)

Junction TypePlate Thickness (mm)Electrode φ mmDifference Gram (mm)Current (A)Voltage (V)Welding Speed (cm/min)
Type I1.01.0050-5513-1540-55
1.21.0060-7014-1630-50
1.61.00100-11016-1740-60
2.31.0 or 1.20-1.0110-12017-1830-40
3.21.0 or 1.21.0-1.5120-14017-1925-30
4.01.21.5-2.0150-17018-2125-40

6.5.6 Airflow Selection

Welding MethodW-type Weld Wire with Thin WireWelded with Coarse WireWelded with Thick Wire at High Currents
Gas Flow (l/min)5~1515~2020~25

7. Maintenance

7.1 General Maintenance

  • Work Environment: Operate in a dry environment with humidity below 90%. Temperature should be between -10°C and 40°C. Avoid welding in open air unless protected from wind and rain. Keep the machine dry and away from wet ground or puddles.
  • Chemicals/Dust: Avoid welding in dusty areas or environments with aggressive chemical gases. Shielded arc welding requires sufficient airflow.
  • Ventilation: The built-in fan is crucial for cooling. Ensure air vents are open and unblocked. Maintain a minimum distance of 30 cm between the machine and nearby objects for proper ventilation.
  • Overvoltage Protection: Do not exceed the specified input voltage. Refer to the "Main Parameters" table. The machine has automatic voltage compensation, but excessive input voltage can damage components.
  • Overload Protection: Do not exceed the maximum load current or duty cycle. Overloading shortens service life and can damage the machine.
  • Over-temperature Protection: If the machine overheats, the overheating LED on the front panel will illuminate. The machine will stop welding. Keep the fan running to cool down the internal temperature. Welding can resume once the LED turns off.

7.2 Regular Checks

Warning: These operations require electrical expertise and comprehensive safety knowledge. Only qualified operators should perform them. Ensure the machine's input cable is disconnected from the power utility before any checks.

  1. Internal Circuit Connections: Periodically check internal circuit connections (especially plugs). Tighten loose connections. If oxidation is present, remove it with sandpaper and reconnect.
  2. Moving Parts: Keep hands, hair, and tools away from moving parts such as fans to avoid personal injury or damage.
  3. Cleaning: Regularly clean dust with dry, clean compressed air. If the welding environment is smoky or polluted, clean the machine daily. Ensure the compressed air is at an appropriate temperature to prevent damage to small internal parts.
  4. Moisture Protection: Avoid rain, water, and vapor infiltration. If the machine gets wet, dry it thoroughly and check the insulation before use.
  5. Cable Insulation: Periodically check the insulation cover of all cables. Replace any worn or damaged parts.
  6. Trachea (Gas Hose): Regularly check the trachea for good condition. Replace if there are any cracks.
  7. Storage: If unused for a long time, store the machine in a dry place in its original packaging.

8. Troubleshooting

Warning: Troubleshooting requires sufficient expertise. Ensure the machine is disconnected from power before attempting any repairs.

SymptomCheck the Steps
The overheating LED is on.
  1. Check welding current and time; operate as per manual.
  2. Check fan operation. If not working, check fan power supply (230V). If power supply is normal, check the fan itself. If abnormal, check connection cable.
  3. If the thermal switch is damaged, replace it.
No response when pressing the gun trigger, protection LED is off.
  1. Check if the power LED and digital meter are lit.
  2. Check if the torch trigger and connection are good.
  3. Check if the wire feeder is well connected.
Wire feeder sends wire into gas when pushing trigger, but no output current, protection LED off.
  1. Check if the power cord to the workpiece is in good contact.
  2. Check if the quick plug is connected correctly.
  3. Check if the wire feeder is well connected.
  4. Inspect the welding torch for damage.
  5. The internal control PCB PK-94 may have failed.
Output current when pushing gun trigger, but wire feeder does not send wire.
  1. Inspect wire feeder for blockage or damage.
  2. Inspect welding torch contacts for blockages or damage.
  3. The wire feed plate PK-93 may be faulty.
Welding can be performed when trigger is pressed, but voltage cannot be adjusted. No-load voltage is too high.
  1. Check that the control cable of the wire feeder is intact.
  2. The control PCB inside the machine may have failed.
Welding current is unstable.
  1. Check that the pressure arm on the wire feeder is at the right pressure.
  2. Check that the drive roller matches the wire size.
  3. Check the contact tip of the welding torch for wear; replace if necessary.
  4. Check that the welding wire is of good quality.
  5. Check if the torch cable is too twisted.
  6. Check if the quick plug is loose.
Weld is not well protected.
  1. Do not immediately remove the welding torch when stopping welding, so that protective gas shields the beads.
  2. Extend the afterflow time of the protective gas.
Large pit after welding.
  1. Select 4T mode for crater welding at low currents.
  2. Change the operating mode.

9. User Tips

  • For optimal flux-cored MIG welding, ensure your wire feed tension is correctly set to avoid tangles or inconsistent feeding.
  • When switching between welding modes, double-check all cable connections and parameter settings to match the selected process.
  • Keep your welding area clean and free of debris to prevent contamination of welds and ensure proper machine ventilation.
  • Regularly inspect your consumables (contact tips, nozzles, electrodes) and replace them when worn to maintain weld quality.
  • If experiencing an unstable arc in MMA mode, try adjusting the electrode type or polarity (DCEP/DCEN) to suit the material.

10. Frequently Asked Questions (FAQ)

Q: Can I use solid wire with this machine?
A: Yes, the HBM1200 supports solid wire for MIG welding, but it requires external shielding gas (e.g., Ar+CO2 mixture) and a gas cylinder, which are not included.
Q: Is a TIG torch included?
A: The standard package includes a MIG burner, ground clamp, and welding clamp. A TIG torch (e.g., WP17V) needs to be purchased separately for Lift TIG welding.
Q: What kind of materials can I weld?
A: The machine is suitable for welding carbon steel, iron, and galvanized steel in MIG/MMA modes. For Lift TIG, it supports stainless steel (with appropriate TIG torch and gas).
Q: How do I know if the machine is overheating?
A: The "Abnormal Indication" light on the front panel will illuminate if the machine is overheating. Stop welding and allow the machine to cool down with the fan running.

11. Warranty and Support

For any issues or questions regarding your HITBOX HBM1200 welding machine, please refer to the official user manual PDF for detailed warranty information and contact your seller or HITBOX customer support. A PDF version of the user manual is available for download: HITBOX HBM1200 User Manual (PDF).

© 2023 HITBOX. All rights reserved.


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.