ANDELI ADL100GV-0022-1

Contents

ANDELI ADL100GV-0022-1 Frequency Converter User Manual

Model: ADL100GV-0022-1

1. Introduction

This manual provides essential information for the safe and efficient installation, operation, and maintenance of the ANDELI ADL100GV-0022-1 Frequency Converter. Please read this manual thoroughly before using the product and keep it for future reference.

2. Safety Instructions

WARNING!

  • To prevent electrical shock, do not open the cover for at least 5 minutes after removing AC power. This allows capacitors to discharge.
  • Ensure proper grounding before connecting power.
  • All wiring should be performed by qualified personnel in accordance with local and national electrical codes.
  • Do not operate the inverter with damaged cables or if it has been dropped or damaged.

CAUTION:

  • Power input should be connected to R.S.T. terminals.
  • Motor should be connected to U.V.W. terminals.
Front view of ANDELI ADL100GV-0022-1 inverter showing control panel and safety warnings
Figure 1: Front view of the ANDELI ADL100GV-0022-1 Frequency Converter, highlighting the control panel and safety labels.

3. Installation and Setup

3.1 Unpacking and Inspection

Upon receiving the inverter, carefully unpack it and inspect for any signs of damage during transit. Verify that all components are present according to the packing list.

3.2 Mounting

Mount the inverter in a vertical position on a flat, non-flammable surface. Ensure adequate clearance around the unit for proper ventilation. Avoid locations with direct sunlight, excessive dust, corrosive gases, or high humidity.

Side view of ANDELI ADL100GV-0022-1 inverter showing ventilation grilles
Figure 2: Side view of the inverter, illustrating the ventilation grilles for heat dissipation.

3.3 Wiring

Refer to the safety instructions for terminal connections. Ensure all connections are tight and secure. Use appropriate wire gauges for the input power and motor connections.

  • Input Power (R, S, T): Connect single-phase AC 220V, 50Hz power supply.
  • Motor Output (U, V, W): Connect to the three-phase motor.
  • Grounding: Connect the ground terminal to a reliable earth ground.

4. Operating Instructions

4.1 Control Panel Overview

The inverter features a digital control panel for setting parameters and monitoring operation. Key components include:

  • FUNC Button: Function key, typically used to access different parameter groups.
  • PRG Button: Program key, used to enter/exit programming mode.
  • Up/Down Arrow Buttons: Used to navigate menus, adjust parameter values, or change frequency.
  • ENTER Button: Confirms selections or saves parameter changes.
  • RUN Button: Starts the motor.
  • STOP/RESET Button: Stops the motor or clears fault alarms.
  • Rotary Knob (Digital Panel): Used for fine-tuning frequency or parameter values.
  • Display Indicators: FWD (Forward), REV (Reverse), ALM (Alarm), Hz (Frequency), A (Current), V (Voltage).

4.2 Basic Operation

  1. Power On: Apply AC power to the inverter. The display will light up.
  2. Start Motor: Press the RUN button. The motor will start and accelerate to the set frequency.
  3. Adjust Frequency: Use the Up/Down Arrow buttons or the Rotary Knob to adjust the output frequency (and thus motor speed).
  4. Stop Motor: Press the STOP/RESET button. The motor will decelerate and stop.
  5. Reset Alarm: If an alarm (ALM indicator) occurs, address the cause, then press STOP/RESET to clear the alarm.

4.3 Parameter Setting

Detailed parameter settings are typically covered in a comprehensive programming manual. For basic adjustments:

  1. Press PRG to enter programming mode.
  2. Use Up/Down Arrow buttons to navigate through parameter groups (e.g., P00, P01, etc.).
  3. Press ENTER to select a parameter group or individual parameter.
  4. Use Up/Down Arrow buttons or the Rotary Knob to change the parameter value.
  5. Press ENTER to save the new value.
  6. Press PRG again to exit programming mode.

5. Maintenance

Regular maintenance ensures optimal performance and extends the lifespan of your frequency converter.

  • Cleaning: Keep the inverter clean and free from dust and debris. Use a soft, dry cloth. Do not use liquid cleaners.
  • Ventilation: Ensure that the ventilation grilles are not obstructed to allow for proper airflow and heat dissipation.
  • Connections: Periodically check all wiring connections for tightness. Loose connections can cause overheating or intermittent operation.
  • Environmental Conditions: Verify that the operating environment remains within the specified temperature and humidity ranges.
  • Capacitor Discharge: Always wait at least 5 minutes after disconnecting power before opening the inverter cover to allow internal capacitors to discharge, preventing electrical shock.

6. Troubleshooting

This section provides general guidance for common issues. For complex problems, contact technical support.

ProblemPossible CauseSolution
Inverter does not power onNo input power; Blown fuse; Internal faultCheck power supply; Inspect fuses; Contact support
Motor does not runIncorrect wiring; Parameter settings; Overload; Emergency stop activeVerify wiring (U,V,W); Check motor parameters; Reduce load; Reset emergency stop
ALM indicator onOvercurrent; Overvoltage; Undervoltage; Overheat; External faultIdentify fault code (if displayed); Address cause (e.g., reduce load, check voltage); Press STOP/RESET
Motor runs erraticallyLoose connections; Motor parameter mismatch; InterferenceCheck all wiring; Verify motor parameters; Ensure proper shielding

7. Specifications

Product Specifications
ModelADL100GV-0022-1
BrandANDELI
Input Voltage1PH AC 220V
Input Frequency50Hz
Output Voltage3PH AC 0-220V
Output Power2.2kW
Output Current10A
Frequency Range0-300Hz
DIY Supplies CategoryElectrical
OriginMainland China, Zhejiang Province
Standard ComplianceIEC61800-2 1998
CertificationsISO9001, ISO1400
Package Dimensions (L x W x H)10 cm x 11 cm x 11 cm
Package Weight2.5 kg
Product label for ANDELI ADL100GV-0022-1 inverter showing model, input/output, frequency range, and standards
Figure 3: Product label with detailed specifications and compliance information.

8. User Tips

No specific user tips were available from reviews or Q&A for this product. Always refer to the detailed parameter manual for advanced configurations and specific application requirements.

9. Warranty and Support

The ANDELI ADL100GV-0022-1 Frequency Converter is manufactured by ANDELI. For warranty information, please refer to the terms provided at the time of purchase or contact your vendor.

9.1 Technical Support

For technical assistance or inquiries, please contact the seller:

  • Seller: Firefly Tool Specialty Store Zc115 Store
  • Email: 397384418@qq.com
  • WeChat/Whatsapp: +8613907407457

When contacting support, please provide your product model (ADL100GV-0022-1) and a detailed description of the issue.

© 2023 ANDELI. All rights reserved. Information in this manual is subject to change without notice.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.