JIKONG 4.3 Inch Touch Screen Display

Contents

JIKONG 4.3 Inch Touch Screen Display User Manual

Brand: JIKONG | Model: 4.3 Inch Touch Screen Display

Version: 2.0

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of the JIKONG 4.3 Inch Touch Screen Display. This display is designed to interface with JKBMS V19 systems, providing real-time monitoring of battery parameters and system status. Please read this manual thoroughly before installation and use to ensure proper functionality and safety.

2. Safety Information

Always observe the following safety precautions:

  • Ensure all power sources are disconnected before installation or maintenance.
  • Avoid exposing the display to extreme temperatures, moisture, or direct sunlight.
  • Do not attempt to disassemble or modify the display, as this may void the warranty and cause damage.
  • Handle cables and connectors with care to prevent damage.
  • Ensure proper grounding if required by your system setup.

3. Package Contents

Verify that all items are present in your package:

  • JIKONG 4.3 Inch Touch Screen Display
  • Cable A (Long 3000mm)
  • Cable B (Long 300mm)
  • Cable C (Long 280mm)
  • Switch Cable (Long 120mm)
  • Mounting Buckles/Screws

4. Product Overview

4.1. Display Appearance

The front of the display provides a comprehensive overview of your battery management system's status. Key indicators include:

  • Vol: Battery Pack Total Voltage
  • Cur: Output Current
  • SOC: State of Charge (Battery Percentage)
  • Delta Vol: Cell Voltage Deviation
  • Ave Vol: Average Cell Voltage
  • MOS: MOS Temperature
  • Balance: Cell Balancing Status (ON/OFF)
  • Charge: Charging Status (ON/OFF)
  • Discharge: Discharging Status (ON/OFF)
  • Alarm: System Alarm Indicator
  • Language Selection: English or Chinese (Support customizing language)
Front view of the JIKONG 4.3 inch Touch Screen Display, showing voltage, current, state of charge (SOC), cell voltage deviation, average cell voltage, MOS temperature, balance status, charge/discharge status, and alarm indicators.
Figure 1: JIKONG 4.3 Inch Touch Screen Display Front View with Labeled Elements

4.2. External Interfaces

The rear of the display features the main connection port and an SD card slot.

  • User Interface: This port is used for power supply and serial port signal connection to the JKBMS. It utilizes an HY2.0 mm-8P horizontal mount socket.
  • SD Card Interface: Supports SD/SDHC cards for potential firmware updates or data logging (functionality depends on BMS model).
Back view of the JIKONG 4.3 inch Touch Screen Display, highlighting the TF Card Holder and the main connector interface.
Figure 2: JIKONG 4.3 Inch Touch Screen Display Back View with TF Card Holder

4.3. Dimensions

The physical dimensions of the display are as follows:

  • Overall Width: 98.0 mm
  • Overall Height: 140.0 mm
  • Display Area Width: 95.0 mm
  • Display Area Height: 53.9 mm
  • Maximum Thickness: 28.8 mm
  • Mounting Hole Diameter: 4-Ø7.0 mm

5. Specifications

5.1. General Parameters

Parameter Data
Display CategoryTFT
Size/Resolution95.0mm(W)×53.9mm(H) / 480*272
Display Colors65K True Color
Backlight Type/BrightnessLED / 300nit/m²
Viewing Angle L/R/U/D70°/70°/50°/70°
Operating/Storage Temperature-20~+70°C / -30~+85°C
SD Card InterfaceSD/SDHC

5.2. Power Supply

Parameter Min Value Max Value
Power Supply Voltage (with reverse polarity protection)6V36V
Power Consumption1.4W (12V@116mA)

5.3. Pin Definition (HY2.0 mm-8P Horizontal Mount)

Pin No. Pin Name Pin Description
1GNDGround
2GNDGround
3485+Serial Port RS-485 Signal A
4NCUndefined
5NCUndefined
6485-Serial Port RS-485 Signal B
7VCCPower Supply
8VCCPower Supply

5.4. Working Environment and Reliability Parameters

Parameter Test Environment Min Value Typical Value Max Value Unit
Operating Temperature12V voltage, 60% humidity-202570°C
Storage Temperature-302580°C
Operating Humidity25°C10%60%90%RH

6. Installation Instructions

Follow these steps to install the JIKONG 4.3 Inch Touch Screen Display:

  1. Prepare the Opening: Create an appropriate opening in your panel or enclosure according to the display's dimensions (refer to Section 4.3). The mounting holes are typically marked by red circles in diagrams and are located on the top and bottom of the HMI.
  2. Embed the HMI: Carefully insert the HMI into the prepared opening from the front. Ensure it sits flush with the panel.
  3. Secure with Buckles: From the rear of the panel, insert the provided buckles into the mounting holes on the HMI. Push them firmly until they engage and secure the display.
  4. Tighten Screws (if applicable): If your mounting system includes screws for additional security, tighten them to firmly fix the HMI to the device.
JIKONG 4.3 inch Touch Screen Display with its connecting cables (Cable A, B, C) and the switch cable, illustrating the physical components included.
Figure 3: JIKONG 4.3 Inch Touch Screen Display and Cables for Installation

7. Wiring Diagram

The display connects to the JKBMS protection board using specific cables. Ensure correct connections to avoid damage.

  • Protection Board End Cable: Total length 0.5 meters, typically features a circular connector for the BMS.
  • Display End Cable: Total length 2.5 meters, connects to the display's user interface port. It includes loose wires (10CM length) and a switch cable (15CM length) for external control. The switch cable (120mm long) allows you to turn the BMS ON/OFF with a long press.
Wiring diagram illustrating the connection of the JIKONG 4.3 Inch Display to a JKBMS protection board and battery cells. This diagram shows the overall system integration.
Figure 4: Typical Wiring Diagram for JIKONG 4.3 Inch Display with JKBMS

Refer to the specific JKBMS manual for detailed wiring instructions for your particular BMS model, especially for balance and temperature sensor connections.

8. Operation

Once installed and wired, the display will power on and show real-time data from your JKBMS. The touch screen allows for interaction and navigation through different information screens.

  • Power On/Off: Use the external switch cable (long press) to turn the connected BMS ON or OFF. The display will reflect the BMS status.
  • Monitoring Data: The main screen displays critical parameters such as total voltage, current, state of charge (SOC), and individual cell information.
  • Language Selection: The display supports English and Chinese. Look for a language icon (e.g., '中/EN') on the screen to switch between languages.
  • Alarm Indicators: Pay attention to the 'Alarm' section. If an alarm is active, investigate the cause immediately.
  • Navigation: Tap on different sections of the screen (e.g., 'STATUS', 'CELLS VOLTAGE', 'ALARM') to view more detailed information or access settings (if available for your BMS firmware).

9. Maintenance

  • Cleaning: Use a soft, dry cloth to clean the display screen. Avoid abrasive cleaners or solvents that could damage the screen surface.
  • Environmental Conditions: Operate the display within the specified temperature and humidity ranges to ensure longevity.
  • Firmware Updates: Periodically check the JIKONG official website or your BMS provider for any available firmware updates for the display or BMS. Updates may improve performance or add new features. Use the SD card slot for updates if supported.

10. Troubleshooting

  • Display Not Powering On:
    • Check all cable connections, especially the power supply to the user interface port.
    • Ensure the BMS is powered on and functioning correctly.
    • Verify the input voltage is within the 6V-36V range.
  • Incorrect Readings:
    • Confirm that the display is correctly connected to the BMS's serial communication port.
    • Ensure the BMS itself is calibrated and providing accurate data.
  • Touch Screen Unresponsive:
    • Restart the system by cycling power to the BMS and display.
    • Ensure the screen is clean and free from debris or moisture.
  • Alarms Displayed:
    • Refer to your JKBMS manual for specific alarm codes and their meanings.
    • Address the underlying issue indicated by the alarm (e.g., overcharge, over-discharge, overcurrent, short circuit, temperature anomaly).

11. User Tips

  • For optimal readability, install the display in a location free from direct glare.
  • Regularly check the 'Alarm' section of the display to proactively identify and address potential battery issues.
  • Keep the display's firmware updated to benefit from the latest features and improvements.

12. Support and Documentation

For further detailed technical information, specific wiring diagrams for various JKBMS models, or advanced troubleshooting, please refer to the official user manual PDF provided by JIKONG. A digital version of the user manual can be found at: JIKONG 4.3 Inch Display User Manual (PDF).

For customer service or technical assistance, please contact your vendor or the official JIKONG support channels.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.