Introduction
Thank you for choosing the BUTURE BC02 Car Jump Starter with Air Compressor. This versatile device combines a powerful jump starter, a portable air compressor, a power bank, and an emergency light, making it an essential tool for any vehicle owner. Please read this manual carefully before use to ensure safe and optimal operation.
Figure 1: BUTURE BC02 Jump Starter and included accessories.
Important Safety Information
- Always wear eye protection when working with batteries.
- Do not allow the jump starter clamps to touch each other once connected to the device.
- Do not jump start a frozen battery.
- Ensure the device is fully charged before use for optimal performance.
- Keep out of reach of children.
- Do not expose the device to extreme temperatures or moisture.
- If the device becomes excessively hot during use, discontinue operation immediately.
Package Contents
Please check the package for the following items:
- BUTURE BC02 Jump Starter with Air Compressor
- Smart Battery Clamps
- Air Hose
- Nozzle Adapters (for various inflatables)
- USB-C Charging Cable
- User Manual
- Storage Bag
Setup and Initial Charging
Before first use, ensure the BUTURE BC02 is fully charged. The device features a large LED screen that displays the battery level.
- Connect the provided USB-C charging cable to the USB-C input port on the device.
- Connect the other end of the USB-C cable to a suitable USB wall adapter (not included) or car charger.
- The LED screen will indicate charging status and battery percentage. Charge until the screen shows 100%.
Figure 2: Charging the BC02 and using it as a power bank.
It is recommended to recharge the device every 3-6 months, even if not in use, to maintain battery health.
Operating Instructions
1. Jump Starting a Vehicle
The BUTURE BC02 can jump start vehicles with up to 9.0L gas engines and 8.0L diesel engines.
- Ensure the jump starter is sufficiently charged (at least 50% recommended).
- Insert the smart battery clamp plug firmly into the jump starter's 12V output port. The indicator light on the clamp will flash red and green alternately.
- Connect the red (+) clamp to the positive (+) terminal of the vehicle's battery.
- Connect the black (-) clamp to the negative (-) terminal of the vehicle's battery.
- Once connected correctly, the indicator light on the smart clamp will turn solid green. If it flashes red or beeps, check connections or refer to the troubleshooting section.
- Start your vehicle within 30 seconds.
- Once the vehicle starts, immediately remove the smart clamp from the vehicle battery, then disconnect it from the jump starter.
Figure 3: Easy steps to jump start your vehicle.
Force Start Function: If the battery is extremely low and the smart clamp does not show a solid green light, consult the troubleshooting section for instructions on using the force start function (if available and safe for your vehicle).
2. Using the 150PSI Air Compressor
The integrated air compressor can inflate tires and other inflatables up to 150 PSI with smart preset and auto-stop features.
- Press the power button to turn on the device.
- Connect the air hose to the inflation port on the device and tighten it.
- Attach the other end of the air hose to the item you wish to inflate (tire valve, ball needle, etc.). Use the appropriate nozzle adapter if necessary.
- Short press the 'M' button to enter inflation mode.
- Press 'M' again to cycle through inflation modes (Car, Motorcycle, Bicycle, Ball, Custom) or 'U' to change pressure units (PSI, BAR, KPA).
- Use the '+' and '-' buttons to set the desired pressure.
- Long press the power button for 3 seconds to start inflation. The compressor will automatically stop when the preset pressure is reached.
- Once inflation is complete, disconnect the air hose from the item and the device.
Figure 4: Steps for using the air compressor.
Inflation Pressure Ranges:
- Car: 26-51 PSI
- Motorcycle: 26-44 PSI
- Bicycle: 30-65 PSI
- Ball: 4-16 PSI
- Custom Inflation: 0-150 PSI
Figure 5: Recommended inflation ranges for various items.
3. Using as a Portable Power Bank
The BC02 can charge your electronic devices on the go.
- Connect your device's charging cable to the USB-A output port (5V/2.4A) on the jump starter.
- The jump starter will automatically begin charging your device.
- The USB-C port can also be used for input (5V/2A, 9V/2A, 12V/1.5A) to recharge the jump starter itself.
Figure 6: Charging mobile devices with the BC02.
4. Emergency Lights
The device features a 500-lumen LED light with multiple modes for emergency situations.
- Press the light button once for a steady flashlight.
- Press again for white strobe light.
- Press a third time for red strobe light (warning triangle).
- Press a fourth time for SOS signal.
- Press a fifth time to turn off the light.
Figure 7: Emergency light functions.
Maintenance
- Cleaning: Wipe the device with a soft, dry cloth. Do not use harsh chemicals or abrasive materials.
- Storage: Store the device in a cool, dry place away from direct sunlight and extreme temperatures.
- Charging: Recharge the device every 3-6 months to maintain battery life, even if not in use.
- Battery Care: Avoid fully discharging the battery frequently.
Troubleshooting
Specifications
User Tips
- Always keep the jump starter charged, especially before long trips or during cold weather.
- Familiarize yourself with the different inflation modes and pressure units before an emergency.
- Store the device in an easily accessible location in your vehicle.
- Test the emergency light functions periodically to ensure they are working.
Warranty and Support
For warranty information, technical support, or service inquiries, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.
