CEM DT-3809

Contents

Digital LED Light Meter DT-3809 User Manual

Model: DT-3809 | Brand: CEM

1. Introduction

The CEM DT-3809 Digital LED Light Meter is a precision instrument designed to measure the intensity of illumination from various light sources, including LED, fluorescent, metal halide, high-pressure sodium, and incandescent sources. It complies with JISC1609:1993 and CNS 5119 general A class specifications, offering accurate readings in Lux or Foot-candle units. Its spectral response closely matches the CIE luminous spectral efficiency, ensuring reliable measurements across the visible light spectrum.

CEM DT-3809 Digital LED Light Meter with separate sensor
Figure 1: CEM DT-3809 Digital LED Light Meter and its remote sensor. This device measures light intensity in Lux or Foot-candle units.

2. Key Features

  • Compliance with JISC1609:1993 and CNS 5119 general A class specifications.
  • Spectral response closely matches CIE luminous spectral efficiency.
  • Measures illumination intensity in Lux (Lx) or Foot-candle (FC) units.
  • Capable of measuring light sources across the entire visible spectrum.
  • Internal storage for up to 99 records.
  • Cosine angular corrected for accurate readings from various angles.
  • Remote light sensor with approximately 1.5 meters of cable for flexible positioning.
  • Test value up to 400,000 Lux/Fc.
  • Resolution of 0.1 Lux/Fc.
  • Maximum and minimum value retention.
  • Data retention function.
CEM DT-3809 display showing MAX 918 LUX and features like 400,000 Lux/Fc test value, 0.1 Lux/Fc resolution, max/min, and data retention
Figure 2: The DT-3809 meter highlighting its key features and display capabilities.

3. Components Overview

The DT-3809 light meter consists of a main unit with an LCD display and control buttons, and a remote light sensor connected via a coiled cable.

Front view of the CEM DT-3809 Digital LED Light Meter showing buttons and LCD display
Figure 3: Front view of the DT-3809 main unit, displaying the LCD screen and control buttons.

3.1 Main Unit Controls

  • LCD Display: Shows measurement readings, units (Lux/FC), MAX/MIN indicators, battery status, and light source selection.
  • Power Button (Power button icon): Turns the device ON/OFF.
  • LX/FC Button: Toggles between Lux and Foot-candle measurement units.
  • MEM/READ Button: Accesses stored records or saves current readings.
  • HOLD/L.S. Button: Freezes the current reading on the display (HOLD) or selects the light source type (L.S.).
  • ZERO Button: Calibrates the meter to zero in a dark environment.
  • Up/Down Arrows: Used for navigating menus or adjusting settings, such as light source selection.

3.2 Light Sensor

The remote light sensor is connected to the main unit via a coiled cable, approximately 1.5 meters in length. It features a protective cap to shield the sensor when not in use.

Close-up of the remote light sensor for the DT-3809 meter
Figure 4: The remote light sensor with its protective cap removed, ready for measurement.

4. Setup

4.1 Battery Installation

  1. Ensure the device is powered OFF.
  2. Locate the battery compartment on the back of the main unit.
  3. Open the battery compartment cover.
  4. Insert a new 9V battery, observing the correct polarity (+/-).
  5. Close the battery compartment cover securely.

4.2 Connecting the Sensor

The light sensor is permanently connected to the main unit via a coiled cable. No additional connection steps are required.

5. Operating Instructions

5.1 Powering On/Off

  • Press the Power button icon button to turn the meter ON.
  • Press and hold the Power button icon button for a few seconds to turn the meter OFF.

5.2 Selecting Measurement Units (Lux/FC)

  • After powering on, press the LX/FC button to toggle between Lux and Foot-candle units. The selected unit will be displayed on the LCD.

5.3 Zero Calibration

  1. Place the light sensor in a completely dark environment (e.g., cover it with the protective cap).
  2. Press the ZERO button. The display should show "0" or a value very close to zero. This calibrates the meter for accurate readings.

5.4 Taking Measurements

  1. Remove the protective cap from the light sensor.
  2. Position the light sensor at the desired location and angle for measurement.
  3. The current illumination intensity will be displayed on the LCD.
CEM DT-3809 measuring light from an LED bulb, showing a reading of 2675 Lux
Figure 5: The DT-3809 in operation, measuring light from an LED source.

5.5 Data Hold Function

  • Press the HOLD/L.S. button briefly to freeze the current reading on the display. "HOLD" will appear on the screen.
  • Press the HOLD/L.S. button again to release the hold and resume live measurements.

5.6 Light Source Selection (L.S.)

The meter allows for selection of light source types to improve accuracy. Refer to the specifications for available options.

  1. Press and hold the HOLD/L.S. button to enter Light Source selection mode.
  2. Use the Up/Down arrow buttons to cycle through the available light source types (e.g., Tungsten/Daylight, Fluorescent, 0-9 select rating).
  3. Press the HOLD/L.S. button again briefly to confirm your selection and exit the mode.

5.7 Max/Min Reading

The meter can display the maximum and minimum readings recorded during a measurement session.

  • While measuring, press the MEM/READ button to cycle through current, MAX, and MIN readings.
  • The display will indicate "MAX" or "MIN" accordingly.

5.8 Data Storage (99 Records)

The meter can store up to 99 measurement records.

  1. To save a reading, press and hold the MEM/READ button until a storage indicator appears.
  2. To recall stored data, enter the MEM/READ mode and use the Up/Down arrows to browse through the records.

6. Maintenance

6.1 Cleaning

  • Wipe the meter and sensor with a soft, dry cloth.
  • Do not use abrasive cleaners or solvents.
  • Keep the light sensor clean and free from dust or smudges, as this can affect accuracy.

6.2 Battery Replacement

When the low battery indicator appears on the display, replace the 9V battery as described in Section 4.1.

6.3 Storage

  • When not in use for extended periods, remove the battery to prevent leakage.
  • Store the meter and sensor in a cool, dry place, away from direct sunlight and extreme temperatures.
  • Always place the protective cap on the light sensor when storing.

7. Troubleshooting

ProblemPossible CauseSolution
Meter does not power on.Dead or incorrectly installed battery.Replace the 9V battery, ensuring correct polarity.
Inaccurate readings.Sensor dirty, not zero-calibrated, or incorrect light source selected.Clean the sensor, perform zero calibration, and verify the correct light source setting.
Display shows "OL" or "OVER".Measurement range exceeded.The light intensity is beyond the meter's maximum range (400,000 Lux/Fc).
Readings are stuck (not changing).Data Hold function is active.Press the HOLD/L.S. button to release the hold function.

8. Specifications

ParameterValue
Model NumberDT-3809
Brand NameCEM
CertificationCE
ComplianceJISC1609:1993 and CNS 5119 general A class specifications
Spectral ResponseClose to CIE luminous spectral efficiency
Measuring UnitsLux (Lx) or Foot-candle (FC)
Light Source SelectingTungsten/Daylight, Fluorescent, 0~9 select rating
Measuring Range40, 400, 4,000, 40,000, 400,000 Lux; 40, 400, 4,000, 40,000 Foot-candle
Accuracy+/-3% (Calibrated to standard incandescent lamp 2856ºK and corrected LED day while-light spectrum). +/-6% other visible light source.
Data Storage99 records
Sensor Cable LengthApproximately 1.5M
Battery IncludedNo
Accessories9V battery (not included), Gift box
Size (HxWxD)160mm x 58mm x 27mm
Weight280g

9. User Tips

  • For the most accurate readings, ensure the light sensor is positioned directly facing the light source and is not obstructed.
  • Always perform a zero calibration in a dark environment before taking critical measurements.
  • When measuring different types of light sources (e.g., LED vs. fluorescent), remember to adjust the "Light Source Selecting" setting for optimal accuracy.
  • Utilize the data hold function when taking readings in hard-to-reach areas to ensure you capture the correct value.
  • Regularly check the battery level, especially before important measurement tasks, to avoid interruptions.

10. Warranty and Support

The CEM DT-3809 Digital LED Light Meter is manufactured by CEM, a company established in 1991, specializing in professional measuring instruments. Products are manufactured under ISO9001 standards and comply with international quality certifications such as CE, UL, GS, and RoHS.

For warranty information, technical support, or service inquiries, please refer to the official CEM website or contact the authorized distributor from whom you purchased the product. Keep your purchase receipt as proof of purchase.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.