Hantek DSO2C20/2D20/2C35/2D35/2C50/2D50

Contents

Hantek Digital Oscilloscope User Manual

Models: DSO2C20, DSO2D20, DSO2C35, DSO2D35, DSO2C50, DSO2D50 Series

1. Introduction

This manual provides essential information for the safe and efficient operation of your Hantek Digital Oscilloscope. The Hantek DSO2000 series offers a range of models with varying bandwidths and features, including optional waveform generation. Please read this manual thoroughly before using the device to ensure proper functionality and to prevent damage.

Hantek Digital Oscilloscope front view displaying waveforms
Front view of the Hantek Digital Oscilloscope displaying various waveforms.

2. Safety Information

Always observe the following safety precautions to avoid injury and prevent damage to the instrument or other connected devices.

  • Hazardous Voltage: Do not remove the cover of the oscilloscope. Hazardous voltage is present inside. Servicing should only be performed by qualified personnel.
  • Power Source: Ensure the power source voltage matches the requirements specified on the rear panel of the instrument.
  • Grounding: The instrument must be properly grounded to prevent electric shock.
  • Environment: Do not operate the oscilloscope in wet or damp conditions. Avoid operating in explosive atmospheres.
  • Probes: Use only probes and accessories supplied or recommended by Hantek. Ensure probes are correctly rated for the voltage being measured.
Rear panel of the oscilloscope with a warning label about hazardous voltage and power input specifications.
Rear panel of the oscilloscope showing power input and a hazardous voltage warning.

3. Package Contents

Verify that your package contains all the following items:

  • Hantek Digital Oscilloscope Unit
  • Certificate of Conformity
  • Alligator Clip Cable
  • Passive Probe (PP500B)
  • Power Cable
  • Square USB Cable
Image showing the oscilloscope and its accessories: alligator clip cable, power cable, certificate of conformity, passive probe, and square USB cable.
Standard accessories included with the DSO2C20/DSO2C35/DSO2C50 models.
Image showing the oscilloscope and its accessories: alligator clip cable, power cable, certificate of conformity, passive probe, and square USB cable.
Standard accessories included with the DSO2D20/DSO2D35/DSO2D50 models.

4. Product Overview

The Hantek Digital Oscilloscope series features a 7-inch capacitive multi-touch screen with 800x480 pixel resolution. It offers 2 analog input channels and various advanced functionalities for electrical measurements and analysis.

Key Features:

  • Bandwidth: Available in 200MHz, 350MHz, and 500MHz options.
  • Sampling Rate: Up to 2GSa/s (single-channel) / 1GSa/s (all channels) real-time sampling.
  • Memory Depth: 80Kpts (single-channel) / 40Kpts (all channels).
  • Impedance Switching: Supports 1MΩ/50Ω impedance switching for signal integrity.
  • Waveform Generator (DSO2D Series Only): Built-in arbitrary waveform generator capable of outputting 5 standard waveforms (Sine, Square, Ramp, Exp, Noise, DC) and custom arbitrary waveforms, with burst output support. Max frequency 25MHz.
  • Protocol Trigger & Decoding: Five standard serial protocol triggers and decoding, supporting UART, LIN, CAN, SPI, IIC.
  • Measurement Functions: 32 automatic measurement and threshold measurement functions, with statistical analysis. Includes digital voltmeter and hardware frequency meter functions.
  • Remote Control: Standard SCPI remote control instructions for building testing systems.
  • Data Management: Save and export functions for settings, CSV data, images, reference waveforms, and waveforms.
  • Sampling Methods: Normal, average, peak, and high-precision.
  • User Interface: Supports 14 operating languages.
  • Cursor Measurement: Manual and tracking modes, with Math function support.
  • Vertical Measurement: 500uV-10V vertical measurement gear, 300VCAT II withstand voltage input.
  • Display: FFT scale display, XY mode for dual window display.
Hantek Digital Oscilloscope in a lab setting with circuit boards.
The oscilloscope in a typical electronic lab environment.

5. Specifications

Model Comparison

Model Analog Channel Analog Bandwidth Real time sampling rate Memory Depth Waveform Generator Decode
DSO2C202200MHz2GSa/s80K-5 types
DSO2C352350MHz2GSa/s80K-5 types
DSO2C502500MHz2GSa/s80K-5 types
DSO2D202200MHz2GSa/s80K15 types
DSO2D352350MHz2GSa/s80K15 types
DSO2D502500MHz2GSa/s80K15 types
Table comparing different Hantek oscilloscope models based on channels, bandwidth, sampling rate, memory depth, waveform generator, and decode types.
Model comparison table for Hantek DSO2000 series.

Detailed Specifications

Category Specification
LCD Size and Type7-inch capacitive multi-touch screen
Display Resolution800 × 480
Vertical System Analog Channel
Input CouplingDC, AC, GND
Input Impedance1MΩ±1%, 50Ω±1%
Input Capacitance17pF±3pF
Maximum Input Voltage1MΩCAT I 300 VRMS, 400 Vpk; Transient Overvoltage 1600 Vpk
50Ω5VRMS
Vertical Resolution8bit
Vertical Sensitivity Range1MΩ500uV/div ~ 10V/div
50Ω500uV/div ~ 1V/div
Offset Range1MΩ±1V (500uV/div ~ 50 mV/div)
±10V (100mV/div ~ 500 mV/div)
±100 V (1V/div ~ 10 V/div)
50Ω±1V(500uV/div ~ 50 mV/div)
±10V(100mV/div ~ 500 mV/div)
±100V(1 V/div )
Dynamic Range±5div ( 8bit )
Bandwidth Limit (Typical)20MHz,100MHz,200MHz,350MHz; selectable for each channel
DC Gain Accuracy±3%FullScale
DC Offset Accuracy<200mV/div (±0.1div±2mV±1.5%of offset value)
>200mV/div (±0.1div±2mV±1.0%of offset value)
Channel-to-Channel Isolation40dB, from DC to maximum rated bandwidth of each model
ESD Tolerance±8kV (on input BNCs)
Horizontal System Analog Channel
Range of Time Base200MHz: 2ns/div~1ks/div350MHz: 1ns/div~1ks/div500MHz: 500ps/div~1ks/div
Time Base Accuracy±50ppm
Time Base Delay Rangebefore triggering≥1/2 screen width
after triggering1 s or 100 div, whichever is greater
Time Interval (ΔT)Measurement±(1 sample interval)±(50ppm××readout)±50ps
Horizontal ModeYTDefault
XYX1 = Channel1, Y1 = Channel2
SCANTime base≥100ms/div, available to enter or exit the SCAN mode by rotating the Horizontal SCALE knob
ROLLTime base≥100ms/div, available to enter or exit the ROLL mode by rotating the Horizontal SCALE
Acquisition System
Max. Sample Rate of Analog Channel2GSa/s (single-channel), 1GSa/s (all channels)
Max. Memory Depth80Kpts (single-channel), 40Kpts (all channels)
Acquisition ModeNormalDefault
Peak DetectionCapture 1ns glitches
Average Mode2, 4, 8, 16…128 are available for you to choose, averaging point by point
High Resolution12bits (max.)
Arbitrary Waveform Generator (DSO2D Series Only)
Sample Rate200MSa/s
Vertical Resolution12bit
Max. Frequency25MHz
Standard WaveformSine, Square, Ramp, Exp, Noise, DC
ArbArb1, Arb2, Arb3, Arb4
SineFrequency Range0.1Hz~25MHz
SquareFrequency Range0.1Hz~10MHz
RampFrequency Range0.1Hz~1MHz
ExpFrequency Range0.1Hz~5MHz
ArbFrequency Range0.1 Hz-25MHz
Waveform Length4K
FrequencyAccuracy100ppm(<10kH), 50ppm(>10kHz)
Resolution100 mHz or 4 bits (whichever is greater)
AmplitudeOutput Range10mV~7Vpp(HighZ)
5mV~3.5Vpp(50Ω)
DC Offset AccuracyRange±3.5V, HighZ
±1.75V, 50Ω
Resolution100 uV or 3 bits (whichever is greater)
Accuracy2%(1 kHz)
Output Impedance50Ω ± 1%
Detailed technical specifications table for Hantek oscilloscopes, covering vertical, horizontal, acquisition, and arbitrary waveform generator systems.
Detailed technical specifications.

6. Setup

  1. Power Connection: Connect the provided power cable to the AC input on the rear panel of the oscilloscope and then to a suitable power outlet.
  2. Probe Connection: Connect the passive probe (PP500B) to the desired input channel (CH1 or CH2) on the front panel. Ensure a secure connection.
  3. Grounding: Attach the probe's ground clip to the circuit's ground point.
  4. USB Connection (Optional): For PC connectivity and data transfer, connect the square USB cable from the oscilloscope's USB port to your computer.
  5. Power On: Press the power button to turn on the oscilloscope.

7. Operating Instructions

Basic Operation:

  • Channel Selection: Use the CH1 and CH2 buttons to enable or disable input channels.
  • Vertical Controls: Adjust the vertical scale (Volts/Div) and position using the dedicated knobs for each channel.
  • Horizontal Controls: Adjust the horizontal time base (Sec/Div) and position using the corresponding knobs.
  • Trigger Settings: Use the TRIGGER LEVEL knob and related menu options to stabilize waveforms.
  • AUTO Measurement: Press the 'AUTO' button for automatic waveform setup and measurement.

Advanced Functions:

  • Waveform Generator (DSO2D Series): Access the waveform generator menu to select standard waveforms (Sine, Square, Ramp, Exp, Noise, DC) or load custom arbitrary waveforms. Adjust frequency, amplitude, and offset as needed.
  • Measurements: Utilize the 32 automatic measurement functions for parameters like Vpp, Vmax, Vmin, Freq, Period, etc. Cursor measurement modes (manual and tracking) are also available.
  • Decoding: Use the decode function for serial protocols such as UART, LIN, CAN, SPI, IIC.
  • Save/Export: Use the save/export function to store settings, CSV data, screenshots, and waveform data to a USB drive.
  • Display Modes: Switch between YT (time-domain), XY (phase comparison), SCAN, and ROLL modes as required for your analysis.

Video demonstrating the Hantek Digital Oscilloscope in operation.

8. Maintenance

  • Cleaning: Clean the instrument's exterior with a soft, damp cloth. Do not use abrasive cleaners or solvents.
  • Storage: Store the oscilloscope in a dry, dust-free environment when not in use.
  • Calibration: Periodic calibration by qualified service personnel is recommended to maintain accuracy.
  • Software Updates: Check the manufacturer's website for any available firmware updates to ensure optimal performance.

9. Troubleshooting

  • No Power: Ensure the power cable is securely connected to both the oscilloscope and the power outlet. Check the power switch.
  • No Waveform Display: Verify that probes are correctly connected to the input channels and the circuit under test. Check channel enable settings. Adjust vertical and horizontal scales.
  • Unstable Waveform: Adjust the trigger level and trigger mode settings. Ensure the trigger source is correctly selected.
  • Incorrect Measurements: Check probe attenuation settings (1X, 10X) on both the probe and the oscilloscope. Ensure proper grounding.
  • Device Not Responding: Try restarting the oscilloscope. If the issue persists, contact technical support.

10. User Tips

  • For precise measurements, always perform a probe compensation adjustment before use.
  • When measuring high-frequency signals, use the 50Ω input impedance setting if your signal source is also 50Ω to minimize reflections.
  • Utilize the 'Single' trigger mode for capturing non-repeating or transient events.
  • Explore the various decoding options for serial communication protocols to streamline debugging of embedded systems.

11. Warranty and Support

For warranty information, technical support, or service inquiries, please refer to the official Hantek website or contact your authorized dealer. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.