Foursun KMWThunder 12V 100Ah LiFePO4 Battery

Contents

Foursun 12V 100Ah LiFePO4 Battery User Manual

Model: KMWThunder 12V 100Ah LiFePO4 Battery

1. Product Overview

The Foursun KMWThunder 12V 100Ah LiFePO4 Battery is a high-performance, deep-cycle lithium iron phosphate battery designed for a wide range of applications including motorhomes, solar energy systems, camping, boats, golf carts, and UPS backup. It features a built-in Battery Management System (BMS) for enhanced safety and longevity, including low-temperature charging protection.

Foursun 12.8V 100Ah LiFePO4 Battery
Figure 1: Foursun 12.8V 100Ah LiFePO4 Battery with handle and M8 terminals.
Battery label with specifications and warnings
Figure 2: Battery label displaying model, capacity, voltage, current limits, temperature ranges, and safety warnings.

2. Safety Instructions

  • Do not short-circuit the positive and negative poles.
  • Do not modify or disassemble the battery without authorization.
  • Do not throw the battery into fire or water.
  • Please use the standard charger that matches the output voltage of the lithium battery.
  • Keep out of reach of children.
  • Avoid extreme temperatures.

⚠ WARNING: This product can expose you to chemicals including lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

3. Setup and Installation

3.1 Initial Charging

Upon receiving your battery, it is recommended to fully charge it to 14.4V before initial use. Use a standard LiFePO4 charger.

3.2 Connecting Terminals

The battery is equipped with M8 terminals. Ensure all connections are secure and properly tightened to prevent arcing and ensure optimal performance. Connect the positive (+) terminal (red) to the positive lead and the negative (-) terminal (black) to the negative lead of your system.

Top view of battery terminals
Figure 3: Top view of the battery showing the positive (red) and negative (black) M8 terminals.

3.3 Series and Parallel Connections

The Foursun LiFePO4 battery supports up to 4 batteries in series (4S) or 4 batteries in parallel (4P) to achieve higher voltage (24V, 36V, 48V) or higher capacity (up to 800Ah). For example, a 4S4P configuration can provide up to 20.48KWH.

Important Considerations for Series/Parallel Connections:

  1. Voltage Balancing: Before connecting multiple batteries in series or parallel, ensure all batteries are fully charged separately and then connected in parallel for 1-2 hours to allow them to balance their voltage. This is crucial for optimal performance and longevity.
  2. Wiring: Use thicker connecting wires for series connections to handle increased voltage and current safely.
  3. Matching Batteries: For best results, use batteries of the same model and capacity when connecting in series or parallel.
RV Power System Diagram with 4P4S battery connection
Figure 4: Example of an RV power system illustrating 4P4S battery connection for increased power.

4. Operating Instructions

4.1 General Use

This LiFePO4 battery is designed for deep-cycle applications, allowing for 100% depth of discharge, unlike lead-acid batteries which are typically limited to 40-50% discharge. This provides more usable energy from the same capacity.

4.2 Temperature Ranges

The battery features a built-in BMS with low-temperature charging protection. Adhere to the following temperature guidelines:

  • Charge Temperature: 0°C to 45°C (32°F to 113°F)
  • Discharge Temperature: -20°C to 65°C (-4°F to 149°F)
Low-Temperature Charging Protection details
Figure 5: Low-Temperature Charging Protection details, showing operating temperature ranges.

4.3 Power Usage Examples

The 1280Wh capacity provides significant power for various devices. Here are some estimated runtimes:

  • Light (50W): 25 hours
  • Microwave (800W): 1.5 hours
  • Fridge (250W): 5 hours
  • Coffee Machine (300W): 4 hours
Power usage examples and runtimes
Figure 6: Examples of power usage and estimated runtimes for common appliances.

5. Maintenance

LiFePO4 batteries require minimal maintenance compared to lead-acid batteries. Follow these guidelines to ensure maximum lifespan:

  • Regular Inspection: Periodically check battery terminals for corrosion or loose connections. Clean as necessary.
  • Charging: Always use a compatible LiFePO4 charger. Avoid overcharging or undercharging.
  • Storage: If storing the battery for an extended period, ensure it is charged to approximately 50% state of charge and stored in a cool, dry place within the recommended temperature range. The self-discharge rate is less than 3% per month.
  • Physical Protection: The battery features an IP67 waterproof rating and a reliable ABS case for resistance to heat and shock. While durable, avoid unnecessary physical impact or exposure to extreme conditions beyond its rating.

6. Troubleshooting

6.1 Built-in BMS Protections

The advanced Battery Management System (BMS) provides comprehensive protection for the battery, ensuring safe operation and extending its lifespan. The BMS protects against:

  • Low Temperature
  • High Temperature
  • Over-charge
  • Over-discharge
  • Over-current Cutoff
  • Short Circuit
  • Moisture-Proof
  • Dust-Proof
Diagram of 8 BMS protections
Figure 7: Diagram illustrating the 8 comprehensive BMS protections.

6.2 Common Issues and Solutions

  • Battery Not Functioning After Connection: If connecting multiple batteries in series or parallel, ensure all batteries were fully charged and voltage balanced before connection. An imbalance can prevent the system from operating correctly.
  • Reduced Performance: Check all cable connections for tightness and corrosion. Ensure the charger is compatible and functioning correctly. Verify that the operating temperature is within the specified range.

7. Specifications

FeatureSpecification
ModelKMWThunder 12V100AH
Battery TypeLiFePO4 (Lithium Iron Phosphate)
Nominal Voltage12.8 V
Nominal Capacity100 Ah
Energy1280 Wh
Cycle Life4500+ cycles (up to 15,000 cycles)
Max Charge Current50 A
Max Discharge Current100 A
Charge Voltage14.4 ± 0.2 V
Charge Temperature0°C to 45°C (32°F to 113°F)
Discharge Temperature-20°C to 65°C (-4°F to 149°F)
Item Weight11 kg (24.25 lbs)
Item Length33.2 cm (332 mm)
Item Width17.2 cm (172 mm)
Item Height22 cm (220 mm)
Terminal TypeM8
Terminal Configuration+ Pole left
Case MaterialReliable ABS
Waterproof RatingIP67
Self-Discharge Rate<3% per month
Max Series/Parallel4S4P (4 in series, 4 in parallel)
BMS ProtectionsLow Temp, High Temp, Over-charge, Over-discharge, Over-current Cutoff, Short Circuit, Moisture-Proof, Dust-Proof
Battery dimensions and features
Figure 8: Detailed view of battery dimensions and key features.
LiFePO4 battery performance comparison
Figure 9: Comparison highlighting the superior performance and features of the LiFePO4 battery.

8. User Tips

  • The battery charges remarkably fast and maintains its charge for extended periods, making it highly efficient for various applications.
  • The integrated low-temperature BMS protection is a significant advantage, allowing for safe charging in colder environments where many other batteries would fail.
  • Tests confirm that the battery's capacity closely matches its advertised specifications.
  • The battery is well-constructed and internally secured, indicating good manufacturing quality.
  • When connecting multiple batteries in series or parallel, always ensure they are fully charged and voltage-balanced beforehand to prevent issues.
  • For series connections, use appropriately thick connecting wires to safely handle the increased voltage and current.
  • This battery can be used to start engines, similar to a lead-acid battery, and can continuously draw up to 80A from its 100Ah capacity.

9. Frequently Asked Questions (FAQ)

Q: What are the dimensions of the Foursun 12V 100Ah battery?
A: The dimensions are approximately 33.2 cm (Length) x 17.2 cm (Width) x 22 cm (Height).
Q: Can this battery be used to start a car or engine?
A: Yes, it can be used to start an engine like a traditional lead-acid battery. It can continuously draw up to 80A from its 100Ah capacity for starting purposes.
Q: What is the power of the charger for this battery?
A: The battery supports a maximum charge current of 50A. The power of an optional charger can vary; some users have reported chargers with 6A, 9A, or 20A output. Always ensure your charger is compatible with LiFePO4 batteries and provides the correct voltage (14.4 ± 0.2V).

10. Warranty and Support

The Foursun 12V 100Ah LiFePO4 Battery is designed for a long service life, estimated at 15 years or more, with 4500+ charge cycles. For any technical support or inquiries, please contact your retailer or the manufacturer directly. Keep your purchase receipt for any potential claims.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.