MUDIRO 12V5KW Liquid Heater

Contents

MUDIRO 12V5KW Diesel/Gasoline Fuel Liquid Heater Instruction Manual

Model: 12V5KW Liquid Heater

1. Introduction

The MUDIRO 12V5KW Diesel/Gasoline Fuel Liquid Heater is an all-in-one winter solution designed to preheat your vehicle, defrost windows, and protect your engine. This system reduces engine wear, conserves battery power, and ensures a safer, cozier drive in freezing conditions. It is ideal for a wide range of vehicles including trucks, RVs, off-road vehicles, construction trucks, farm cars, cars, yachts, SUVs, and vans.

Key features include a long-range RF remote control for convenient operation up to 500 meters, a smart timer function for scheduled heating, and dual operating modes (P1 and P2) to suit different heating needs. The heater is also equipped with built-in safety mechanisms for overheating and low voltage protection.

MUDIRO 12V5KW Liquid Heater with LCD switch, remote control, and wiring harness
Figure 1: MUDIRO 12V5KW Liquid Heater with main components.

2. Package Contents

Please check the package contents against the list below to ensure all components are present for your version.

2.1 Standard Version

Diagram showing all accessories included in the Standard Version package
Figure 2: Standard Version Accessories.
  • 1x Host (Heater Unit)
  • 1x LCD Monitor
  • 1x Remote Controller
  • 1x Water Pump
  • 1x Oil Pump
  • 1x Oil Filter
  • 1x Air Filter
  • 1x Silencer
  • 1x Exhaust Pipe
  • 1x Inlet Pipe
  • 1x Water Pipe
  • 1x Oil Pump Clamp
  • 1x Fixed Plate
  • 1x Tubing
  • 1x Harness
  • 1x Hose
  • 1x Manual
  • 1x Screw Accessory Kit

2.2 Upgrade Version

Diagram showing all accessories included in the Upgrade Version package
Figure 3: Upgrade Version Accessories.
  • 1x Host (Heater Unit)
  • 1x Upgrade LCD Monitor
  • 1x Remote Controller
  • 1x Water Pump
  • 1x Oil Pump
  • 1x Oil Filter
  • 1x Air Filter
  • 1x Silencer
  • 1x Upgrade Exhaust Pipe
  • 1x Inlet Pipe
  • 1x Water Pipe
  • 1x Oil Pump Clamp
  • 1x Fixed Plate
  • 1x Tubing
  • 1x Harness
  • 1x Hose
  • 1x Manual
  • 1x Screw Accessory Kit
  • 1x Heat-proof Protective Sleeve

3. Specifications

Product information table with dimensions and technical specifications
Figure 4: Product Information and Dimensions.
FeatureSpecification
Thermal Power5KW
Fuel TypeDiesel / Gasoline
Rated Power Consumption19W
Rated Voltage12V
Fuel Consumption (Diesel)0.35-0.53 L/h
Fuel Consumption (Gasoline)0.51-0.63 L/h
Remote Control Distance300-500m
Working Ambient Temperature-40℃ to 80℃
Start-up Power Consumption15-33W (Full Load/Half Load)
Working Power Consumption12-33W (Full Load/Half Load)
Run Time Power36W
Startup Power133W
Dimensions (L*W*H)220mm * 85mm * 160mm
Brand NameMudiro
Switch TypeLCD Switch
External Testing CertificationCE
OriginMainland China
CertificationCE, RoHS
Item TypeHeating & Fans

4. Installation

Proper installation is crucial for the safe and efficient operation of your liquid heater. It is recommended that installation be performed by a qualified professional. Refer to the included manual for detailed, step-by-step instructions and diagrams specific to your vehicle type.

4.1 Basic Heating Principle

The water heating system operates by circulating hot water (coolant) through pipes to terminals for heat release, warming the vehicle's interior and engine. The cooled water then flows back to be reheated, forming a closed-loop cycle.

Diagram illustrating the heating principle with water inlet, water outlet, oil pipe interface, exhaust port, and air inlet
Figure 5: Heating Principle Demonstration.

4.2 Key Installation Points

  • Mounting: Securely mount the main heater unit in a suitable location, ensuring adequate clearance for air intake and exhaust.
  • Fuel System: Connect the oil pump and oil filter to the vehicle's fuel tank according to the diagram. Ensure all connections are leak-free.
  • Coolant System: Integrate the water pump and water pipes into the vehicle's coolant circulation system. This heater is designed to heat the vehicle's coolant, not potable water.
  • Exhaust System: Install the exhaust pipe and silencer, directing exhaust gases safely away from the vehicle and cabin. The upgraded version includes a heat-proof protective sleeve for enhanced safety.
  • Electrical Connections: Connect the wiring harness to the vehicle's 12V power supply and the heater components (LCD monitor, remote receiver). Pay close attention to polarity and fuse requirements.
  • Air Intake: Ensure the air filter is properly installed and positioned to draw clean air.

5. Operation

Your MUDIRO liquid heater offers flexible control options and smart heating modes.

5.1 Remote Control and LCD Switch

The heater can be controlled via the included RF remote control from a distance of 300-500 meters, or directly using the LCD switch panel.

RF Remote Control features including large digital display, temperature adjustment, 500m range, and timed activation
Figure 6: RF Remote Control and LCD Switch features.
  • Power On/Off: Use the designated buttons on the remote or LCD panel to turn the heater on or off.
  • Temperature Adjustment: Adjust the desired target temperature using the controls.
  • Parameter Adjustment: Access settings to modify various operational parameters.
  • Timed Activation: Program up to three separate start/stop times per day to automatically preheat your vehicle.

5.2 Smart Dual-Mode Operation

The heater features two intelligent operating modes:

  • P1 Mode (Single Heating): In this mode, the heater runs once until the target temperature (e.g., 80°C) is reached, then shuts off automatically without restarting. This mode is ideal for initial warm-ups or precise, single heating tasks.
  • P2 Mode (Smart Cycle Mode - Energy Saving): This mode automatically turns the heater on when the temperature drops below a lower set point and turns it off when it reaches the upper set point. The water pump continues circulating between cycles to ensure even heat distribution and consistent temperature maintenance, saving energy.
Graph demonstrating the Smart Cycle Mode (P2) with temperature fluctuations over time
Figure 7: Smart Cycle Mode (P2) operation.

6. Maintenance

Regular maintenance ensures the longevity and optimal performance of your MUDIRO liquid heater.

  • Glow Plug: The glow plug is a critical component for ignition. The standard version's glow plug has a service life of approximately 1000 cycles. The upgraded version, equipped with a Kyocera glow plug, boasts an extended service life of up to 4000 cycles.
  • Fuel Filter: Periodically inspect and replace the fuel filter to prevent contaminants from reaching the oil pump and heater unit.
  • Air Filter: Check and clean or replace the air filter as needed to ensure proper airflow and combustion.
  • Connections: Regularly inspect all fuel, coolant, and electrical connections for leaks, corrosion, or damage. Tighten any loose connections.
  • Exhaust System: Ensure the exhaust pipe and silencer are free from blockages and damage. If you have the upgraded version, check the heat-proof protective sleeve for integrity.
  • General Cleaning: Keep the exterior of the heater unit clean and free from debris.
Close-up of a glow plug with '4000 CYCLES' text, highlighting superior durability
Figure 8: Kyocera Glow Plug for extended service life.
Comparison chart of MUDIRO heater vs. ordinary heaters, highlighting features like remote range, timing, service life, water pump, and sound
Figure 9: MUDIRO Heater advantages, including brushless water pump and quiet operation.

7. Troubleshooting

This section provides solutions to common issues you might encounter.

  • Heater Not Starting:
    • Check fuel level and ensure the fuel line is not blocked.
    • Verify electrical connections and battery voltage (must be 12V).
    • Ensure the glow plug is functioning correctly.
    • Check for error codes on the LCD monitor and consult the detailed manual for their meaning.
  • Insufficient Heat Output:
    • Ensure the coolant system is properly filled and bled of air.
    • Check for blockages in the air intake or exhaust system.
    • Verify the selected operating mode (P1 or P2) and target temperature.
  • Overheating Protection Activated:
    • This safety feature activates if the heater detects excessive temperatures. Check coolant circulation, ensure the water pump is operating, and clear any obstructions around the heater unit.
  • Low Voltage Protection Activated:
    • The heater will shut down if the vehicle's battery voltage drops too low to prevent further battery drain. Recharge or replace the battery.
  • Remote Control Not Responding:
    • Check the remote control's battery.
    • Ensure there are no significant obstructions between the remote and the heater's receiver.

8. User Tips

  • Continuous Heating for RVs/Caravans: For applications requiring continuous heating, such as radiator heating in a caravan trailer, utilize the P2 (Smart Cycle) mode. This mode is designed to maintain a consistent temperature by cycling the heater on and off, while the water pump continues circulation for even heat distribution.
  • Fuel Type: This heater is compatible with both diesel and gasoline. Ensure you are using the correct fuel type for your setup and that the fuel system is properly configured.
  • Coolant System: The heater is designed to warm the vehicle's engine coolant. It is not intended for heating potable water. Ensure your vehicle's coolant system is in good working order and filled with appropriate coolant.
  • Remote Control: The RF remote control does not utilize GSM technology. It operates via radio frequency, offering a range of up to 500 meters without requiring cellular network coverage.

9. Safety Warnings

  • Always ensure adequate ventilation when operating the heater, especially if installed in an enclosed space.
  • Never operate the heater with damaged fuel lines, exhaust pipes, or electrical wiring.
  • Keep flammable materials away from the heater unit and exhaust outlet.
  • Do not modify the heater or its components. Use only original or approved replacement parts.
  • Regularly check for fuel leaks and address them immediately.
  • The heater operates at high temperatures; avoid touching the unit during or immediately after operation.
  • Always disconnect power before performing any maintenance or inspection.

10. Warranty and Support

For warranty information, technical support, or service inquiries, please refer to the contact details provided in your purchase documentation or contact the MUDIRO customer service directly. Keep your proof of purchase for warranty claims.

© MUDIRO. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.