1. Introduction
The PORTXVNSA NanoVNA-H4 Plus is a portable handheld Vector Network Analyzer (VNA) designed for measuring reflection and transmission coefficients across a wide frequency range. This device is an advanced version of the VNA-H4, offering enhanced performance and user-friendly features. It is an essential tool for HAM radio enthusiasts, RF electronics hobbyists, and professionals requiring precise RF measurements.
2. Key Features
- Ergonomic Design: Features a comprehensively upgraded ergonomic design for comfortable handling and operation.
- Extended Measurement Range: Capable of measurements from 50KHz to 2.7GHz.
- Increased Scan Points: The number of scanning points has been increased to 401 for more detailed analysis.
- SD Card Support: Includes support for an SD card, allowing for convenient storage and export of test data.
- Intuitive Interface: Equipped with a resistive touchscreen and a large knob for easy and precise operation.
- Long Battery Life: Built-in 5000mAh rechargeable battery provides extended operational time.
- High-Quality Display: Features a 4-inch IPS LCD display with wide viewing angles, accurate color reproduction, high contrast, and uniform brightness.
- PC Control: Supports PC control via Nano Saver software for advanced data analysis and saving Touchstone files.
3. Package Contents
Please check your package against the following lists. If any items are missing or damaged, please contact your vendor.
Set 1 (No Memory Card)
- NanoVNA-H4 PLUS Host x1
- USB Type-C cable x1
- 15cm SMA male to male TG316 RF cable x2
- SMA Male Calibration Kit OPEN x1
- SMA Male Calibration Kit Short Circuit x1
- SMA Male Calibration Kit LOAD x1
- SMA female to female connector x1
- Type-C to Type-C cable x1
- Touch Pen x1
- Pick x1
Set 2 (with 32GB Memory Card)
- NanoVNA-H4 PLUS Host x1
- USB Type-C cable x1
- 15cm SMA male to male TG316 RF cable x2
- SMA Male Calibration Kit OPEN x1
- SMA Male Calibration Kit Short Circuit x1
- SMA Male Calibration Kit LOAD x1
- SMA female to female connector x1
- Type-C to Type-C cable x1
- Touch Pen x1
- Pick x1
- 32G memory card x1

4. Initial Setup
- Charging the Device: Connect the NanoVNA-H4 Plus to a power source using the provided USB Type-C cable. The device has a built-in 5000mAh rechargeable battery.
- Power On/Off: Locate the power button on the device. Press and hold to power on or off.
- Touchscreen Calibration (if needed): If the touchscreen responsiveness is not optimal, navigate to the 'CONFIG' menu, then 'TOUCH TEST' or 'TOUCH CAL' to recalibrate. Follow the on-screen instructions.
- SD Card Insertion (if applicable): If your model includes an SD card, gently insert it into the designated slot. This allows for storage of test data.
- Connecting to PC (Optional): For advanced control and data analysis, connect the device to a computer using the Type-C to Type-C cable. Utilize the Nano Saver software on your PC to save Touchstone files, sweep frequency spans, and analyze data.

5. Operating Instructions
The NanoVNA-H4 Plus features a 4-inch resistive touchscreen and a large knob for navigation and parameter adjustment. The device measures reflection and transmission coefficients, essential for analyzing RF components and antenna performance.
5.1 Basic Navigation
- Touchscreen: Tap on menu options or graph points to interact.
- Rotary Knob: Use the large knob on the right side to scroll through menus, adjust values, and confirm selections.
- Buttons: Additional buttons (e.g., 'ON/OFF') may be present for specific functions.

5.2 Performing Measurements
The NanoVNA-H4 Plus is capable of various RF measurements, including:
- Scanning antenna systems and cables.
- SWR (Standing Wave Ratio) and impedance matching.
- Measuring dual-band and triple-band duplexers.
- Port isolation by frequency band.
- Measuring insertion loss of filters.

5.2.1 Calibration
Before accurate measurements, calibration is crucial. Use the provided SMA Male Calibration Kit (OPEN, SHORT, LOAD) and follow the on-screen calibration procedure. This typically involves connecting each standard to the CH0 port and performing the corresponding calibration step.
5.2.2 Setting Frequency Range and Scan Points
Navigate to the 'STIMULUS' menu to set the start and stop frequencies. You can also adjust the number of scan points (up to 401) for finer resolution in your measurements.
5.2.3 Displaying Traces and Markers
The device can display multiple traces (e.g., S11 LogMag, S11 Smith, S21 LogMag). Use the 'DISPLAY' menu to select the desired traces. Markers can be added to pinpoint specific frequencies and read values on the graph.
5.3 Saving Data
Test data can be saved to the inserted SD card. Navigate to the 'SD CARD' menu and select the save option. Data can also be exported to a PC using the Nano Saver software.
6. Maintenance
- Cleaning: Use a soft, dry cloth to clean the device. Avoid using harsh chemicals or abrasive materials.
- Storage: Store the NanoVNA-H4 Plus in a cool, dry place away from direct sunlight and extreme temperatures.
- Battery Care: To prolong battery life, avoid fully discharging the device frequently. Charge it regularly, even if not in use for extended periods.
- Connector Care: Keep the SMA connectors clean and free from dust or debris. Use protective caps when not in use.
7. Troubleshooting
- Device not powering on:
- Ensure the battery is charged. Connect to a power source using the USB Type-C cable and try again.
- Touchscreen unresponsive or inaccurate:
- Navigate to 'CONFIG' -> 'TOUCH TEST' or 'TOUCH CAL' to recalibrate the touchscreen. If the issue persists, ensure the screen is clean and free from obstructions.
- Inaccurate measurements:
- Perform a full calibration using the provided calibration kit. Ensure all connections are secure and the cables are not damaged.
- Firmware upgrade issues (e.g., display/encoder malfunction):
- Only use official firmware updates from trusted sources. Unofficial firmware or incorrect upgrade procedures can lead to device malfunction, including display issues and unresponsive controls. Always back up your device configuration before attempting a firmware upgrade. If issues occur after an unofficial upgrade, contact the vendor or community forums for assistance, as reverting to original firmware might be challenging.
8. Specifications
| Parameter | Value |
|---|---|
| Bandwidth | 50KHz - 2.7GHz |
| Dynamic Range (50KHz-900MHz) | 80dB |
| Dynamic Range (900MHz-1.5GHz) | 60dB |
| Dynamic Range (1.5GHz-2.7GHz) | 50dB |
| Reflection Coefficient (SWR) | <1.1 |
| Frequency Accuracy | <0.5 ppm |
| Frequency Stability | <2.5 ppm |
| Scan Points | 401 |
| Product Size | 160 x 92 x 35mm |
| Battery | 5000mAh rechargeable |
| Display | 4-inch IPS LCD Touchscreen |
9. User Tips
- Firmware Upgrades: Exercise caution when performing firmware upgrades. Only use official firmware provided by the manufacturer or trusted community sources. Unofficial firmware can lead to unexpected behavior, including display issues and non-functional controls. Always ensure you have a reliable backup or a clear understanding of the upgrade process before proceeding.
- PC Software: Leverage the Nano Saver software for PC control to enhance your analysis capabilities, save data in Touchstone format, and manage sweep frequency spans more effectively.
- Calibration: Regular calibration with the provided kit is essential for maintaining measurement accuracy, especially when working with different frequency ranges or setups.
10. Warranty and Support
For warranty information, technical support, or service inquiries, please refer to the documentation provided with your purchase or contact the vendor directly. Keep your purchase records for warranty claims.