1. Introduction
This manual provides instructions for the Yinuogo YNG307 433.92MHz Rolling Code Remote Control. This device is designed to operate compatible COMUNELLO VICTOR series garage door and gate openers. Please read this manual carefully before use to ensure proper operation and programming.
Figure 1: Yinuogo YNG307 Remote Control
2. Important Compatibility Note
This remote control is NOT compatible with 868MHz systems. Please verify your existing remote control model and frequency before attempting to program or use this device.
Figure 2: Frequency Compatibility Check
3. Specifications
| Feature | Detail |
|---|---|
| Model Number | YNG307 |
| Encoding Method | Rolling Code |
| Frequency | 433.92MHz |
| Number of Buttons | 2 Buttons |
| Battery | Included |
| Working Range | 30m - 100m (Open Space) |
| Programming Type | Programming with the receiver |
| Certifications | CE, FCC, RoHS, WEEE |
Compatible Models:
- COMUNELLO VICTOR 2
- COMUNELLO VICTOR 4
- COMUNELLO VICTOR 2 SYNC
- COMUNELLO VICTOR 4 SYNC
Disclaimer: Your remote control must be the same as the picture and your model must be in the list. We are not responsible for incorrect purchases.
Figure 3: Compatible COMUNELLO Remote Models
4. Setup and Programming
The Yinuogo YNG307 remote control functions identically to your original COMUNELLO remote. To program this new remote, you must pair it directly with your existing receiver unit. This process typically involves accessing the receiver and pressing a programming button.
Programming Steps:
- Access the Receiver: Locate your garage door or gate opener's receiver unit. You will need physical access to this unit.
- Consult Original Manual: Refer to the instruction manual for your specific COMUNELLO receiver unit for detailed programming steps. The exact procedure (e.g., pressing a 'Learn' or 'Program' button, holding it for a certain duration) varies by receiver model.
- Initiate Learning Mode: Follow your receiver's manual to put the receiver into 'learning' or 'programming' mode.
- Transmit Signal: While the receiver is in learning mode, press and hold the desired button on your new Yinuogo YNG307 remote control. The receiver should indicate successful pairing (e.g., an LED light flashing or changing color).
- Test Operation: Once programmed, test the remote control to ensure it operates your garage door or gate correctly.
Important: Ensure you have access to your receiver/opener and its original manual before attempting to program the remote. Without the receiver, programming is not possible.
Video: Yinuogo Brand Introduction (General information, not specific programming steps)
5. Operating Instructions
After successful programming, operating your garage door or gate with the Yinuogo YNG307 remote control is straightforward:
- Press the programmed button on the remote control once to activate the garage door or gate opener.
- Press the button again to stop or reverse the operation, depending on your opener's settings.
Ensure you have a clear line of sight to the garage door/gate and that no obstructions are present before operating.
6. Maintenance
Battery Replacement:
The YNG307 remote control comes with a battery included. When the remote's range decreases significantly or it stops responding, it's likely time to replace the battery. The specific battery type and replacement procedure can usually be found by opening the remote's casing (often by removing a small screw or prying gently along a seam). Use a compatible replacement battery.
Cleaning:
Wipe the remote control with a soft, dry cloth. Avoid using harsh chemicals or abrasive cleaners, as these can damage the casing or internal components.
Storage:
Store the remote control in a dry place, away from extreme temperatures and direct sunlight, to prolong its lifespan.
7. Troubleshooting
- Remote not working after programming:
- Ensure the remote's frequency (433.92MHz) matches your receiver. This remote is NOT compatible with 868MHz systems.
- Verify that the programming steps were followed precisely according to your receiver's original manual.
- Check the battery in the remote control. Replace if necessary.
- Ensure you are within the working range (30m-100m in open space) of the receiver.
- Remote has reduced range:
- Replace the battery in the remote control.
- Check for any obstructions between the remote and the receiver.
- Ensure the receiver's antenna is not damaged or obstructed.
- Cannot access the receiver for programming:
- Physical access to the receiver is required for programming. If you cannot access it, you will not be able to program the new remote.
- Consult your garage door/gate opener's installer or manufacturer for guidance on accessing the receiver.
8. User Tips
- Always double-check the frequency of your existing remote and receiver (433.92MHz) before purchasing to ensure compatibility.
- Keep your original receiver manual handy, as it contains specific programming instructions crucial for setting up new remotes.
9. Warranty and Support
For any issues or questions regarding your Yinuogo YNG307 remote control, please contact the seller or manufacturer's customer support. Keep your purchase receipt as proof of purchase.
