Mudiro M-5S WT

Contents

Mudiro M-5S WT 12V Diesel/Gasoline Parking Heater User Manual

Model: M-5S WT

1. Introduction

The Mudiro M-5S WT 12V Diesel/Gasoline Parking Heater is an all-in-one winter solution designed to preheat your vehicle, defrost windows, and protect your engine. This system reduces engine wear, conserves battery power, and ensures a safer, cozier drive in freezing conditions. It is ideal for a wide range of vehicles including trucks, RVs, off-road vehicles, construction trucks, farm cars, cars, yachts, and SUVs.

Mudiro M-5S WT Parking Heater with LCD switch, remote control, and wiring harness
Mudiro M-5S WT Parking Heater with included accessories.
Diagram showing how the heater resolves winter driving issues like defrosting, preheating, engine startup assistance, and battery life extension.
Benefits of using the Mudiro M-5S WT heater in various winter driving scenarios.
Illustrations of various vehicle types including off-road vehicle, construction truck, farm car, car, yacht, truck, SUV, and RV, indicating broad compatibility.
The Mudiro M-5S WT heater is suitable for a wide range of vehicles.

2. Safety Information

Your safety and the heater's durability are top priorities. This advanced water parking heater is equipped with intelligent protection systems. Please read and follow all safety instructions carefully before installation and operation.

  • Ensure proper ventilation during operation to prevent carbon monoxide buildup.
  • Do not operate the heater in enclosed spaces without adequate exhaust ventilation.
  • Always check fuel and electrical connections for leaks or damage before use.
  • Keep flammable materials away from the heater and exhaust pipe.
  • The heater features built-in overheating and low voltage protection. If the heater shuts down unexpectedly, consult the troubleshooting section.
  • Professional installation is highly recommended to ensure correct and safe setup.

3. Product Versions

The Mudiro M-5S WT heater is available in two versions: Standard and Upgrade. Key differences are outlined below:

Comparison table of Mudiro M-5S WT Upgrade Version and Standard Version, detailing differences in oil pump, service life, LCD panel, remote control, heat-proof sleeve, and exhaust pipe.
Comparison of Standard and Upgrade Versions.

Upgrade Version Features:

  • Oil Pump: Kyocera Glow Plug
  • Service Life: 4000 Cycles
  • LCD Panel: Strong signal
  • Remote Control: Upgraded
  • Heat-proof Sleeve: Included
  • Exhaust Pipe: Double Layer

Standard Version Features:

  • Oil Pump: Standard Glow Plug
  • Service Life: 1000 Cycles
  • LCD Panel: Standard
  • Remote Control: Standard
  • Heat-proof Sleeve: Without
  • Exhaust Pipe: Standard
Close-up of a Kyocera glow plug, highlighting its quick ignition and superior durability with an extended service life of up to 4000 cycles.
Kyocera Glow Plug (Upgrade Version).
Close-up of a red heat-proof protective sleeve for the exhaust pipe, designed to prevent burns.
Heat-proof Protective Sleeve (Upgrade Version).

4. Package Contents

4.1. Standard Version Package:

Image showing all accessories included in the Standard Version package, numbered 1 through 16.
Standard Version Accessories.
  1. Host (Heater Unit)
  2. LCD Monitor
  3. Remote Controller
  4. Water Pump
  5. Oil Pump
  6. Oil Filter
  7. Air Filter
  8. Silencer
  9. Exhaust Pipe
  10. Inlet Pipe
  11. Water Pipe
  12. Oil Pump Clamp
  13. Fixed Plate
  14. Tubing
  15. Harness
  16. Hose
  17. Manual
  18. Screw Accessory Kit

4.2. Upgrade Version Package:

Image showing all accessories included in the Upgrade Version package, numbered 1 through 16.
Upgrade Version Accessories.
  1. Host (Heater Unit)
  2. Upgrade LCD Monitor
  3. Remote Controller
  4. Water Pump
  5. Oil Pump
  6. Oil Filter
  7. Air Filter
  8. Silencer
  9. Upgrade Exhaust Pipe
  10. Inlet Pipe
  11. Water Pipe
  12. Oil Pump Clamp
  13. Fixed Plate
  14. Tubing
  15. Harness
  16. Hose
  17. Manual
  18. Screw Accessory Kit
  19. Heat-proof Protective Sleeve

5. Specifications

Product information table with dimensions and technical specifications.
Product Dimensions and Technical Specifications.
Parameter Value
Thermal Power 5KW
Fuel Diesel / Gasoline
Rated Power Consumption 19W
Rated Voltage 12V
Fuel Consumption Diesel 0.35-0.53L/h; Gasoline 0.51-0.63L/h
Remote Control Distance 300-500m
Working Ambient Temperature -40℃ to 80℃
Start-up Power Consumption 15-33W (Full Load/Half Load)
Working Power Consumption 12-33W (Full Load/Half Load)
Run Time Power 36W
Startup Power 133W
Dimensions (L*W*H) 220mm * 85mm * 160mm

6. Principle of Operation

The water heating system operates as a closed-loop cycle. Fuel (diesel or gasoline) is combusted to generate heat, which warms the water. This hot water then circulates through pipes to the vehicle's terminals, releasing heat to warm the interior and engine. The cooled water flows back to the heater to be reheated, ensuring continuous warmth.

Diagram illustrating the heating principle with water inlet, water outlet, exhaust port, air inlet, and oil pipe interface, showing the closed-loop water circulation.
Heating Principle Demonstration.

7. Installation

Proper installation is crucial for the safe and efficient operation of your parking heater. Due to the complexity involving fuel, electrical, and water connections, professional installation by a qualified technician is highly recommended.

General Installation Guidelines:

  1. Mounting the Heater: Securely mount the main heater unit in a suitable location, ensuring it is protected from road debris and water spray. Use the provided fixed plate and screws.
  2. Fuel System Connection: Connect the oil pump and oil filter to your vehicle's fuel tank using the provided tubing and hoses. Ensure all connections are tight and leak-free.
  3. Water System Connection: Integrate the water pump and water pipes into your vehicle's cooling system. Follow the vehicle manufacturer's guidelines for connecting auxiliary heating systems.
  4. Air Intake and Exhaust: Install the air filter on the air inlet and the silencer and exhaust pipe on the exhaust port. Ensure the exhaust pipe is routed safely away from flammable materials and passenger compartments.
  5. Electrical Wiring: Connect the wiring harness to the heater unit, LCD monitor, and remote control receiver. Ensure all electrical connections are secure and correctly polarized. Refer to the detailed wiring diagram in the included manual for specific connections.
  6. Initial Start-up: After installation, perform a thorough check for any leaks (fuel, water) or loose connections. Bleed the fuel system if necessary before the first start-up.

Note: Always refer to the comprehensive installation manual included in your package for detailed, step-by-step instructions and specific wiring diagrams for your model.

8. Operating Instructions

8.1. Remote Control Operation

The heater can be controlled from a distance of 300 to 500 meters using the RF remote control. This allows for convenient activation and timing without line-of-sight barriers.

RF Remote Control showing parameter adjustment, settings, and switch buttons, with a range of up to 500m. Features include large digital display, temperature adjustable, RF remote, and timed activation.
RF Remote Control features.
  • Power ON/OFF: Use the designated buttons on the remote to turn the heater on or off.
  • Temperature Adjustment: Adjust the desired temperature using the parameter adjustment buttons.
  • Settings: Access additional settings or modes via the settings button.

8.2. LCD Monitor and Timing Function

The LCD monitor provides real-time information and allows for detailed control and scheduling.

  • Smart Timer Function: Program up to three separate start/stop times each day. This allows you to pre-set heating schedules to match your routine, ensuring a warm vehicle exactly when needed and optimizing energy usage.
  • Parameter Adjustment: Use the buttons on the LCD panel to adjust parameters such as target temperature, operating mode, and timer settings.

8.3. Smart Dual-Mode Operation

The heater offers two intelligent operating modes to suit different heating needs:

Graph illustrating the Smart Cycle Mode (P2 Mode) where temperature is maintained automatically, saving energy. The graph shows temperature fluctuations between -10°C and 30°C over 60 minutes.
Smart Cycle Mode (P2 Mode) operation.
  • P1 Mode (Single Heating): In this mode, the heater runs until the target temperature (e.g., 80°C) is reached, then shuts off automatically without restarting. This mode is ideal for single, precise heating tasks like initial warm-ups.
  • P2 Mode (Smart Cycle Mode): This is an energy-saving mode. The heater automatically turns on when the temperature drops to a lower set point and turns off when it reaches the upper set point. The water pump continues circulating between cycles for even heat distribution, ensuring consistent temperature maintenance while saving energy.

9. Maintenance

Regular maintenance ensures the longevity and optimal performance of your Mudiro parking heater.

  • Seasonal Checks: Before the start of the cold season, inspect all components for wear and tear.
  • Fuel System: Check fuel lines and connections for leaks or blockages. Replace the oil filter periodically as recommended in the full manual.
  • Water System: Ensure the water pump is functioning correctly and there are no leaks in the water pipes. Check coolant levels in your vehicle.
  • Air Filters: Clean or replace the air filter regularly to ensure proper airflow and combustion.
  • Exhaust System: Inspect the exhaust pipe and silencer for any damage or blockages. Ensure the heat-proof sleeve (if applicable) is intact.
  • Electrical Connections: Verify all electrical connections are secure and free from corrosion.
  • Cleaning: Keep the exterior of the heater unit clean and free from dirt and debris.

10. Troubleshooting

If you encounter issues with your heater, refer to the following common problems and solutions:

Problem Possible Cause Solution
Heater does not start No fuel, low battery voltage, faulty glow plug, air in fuel line, electrical connection issue. Check fuel level, charge battery, inspect glow plug (replace if necessary), bleed fuel system, check wiring harness.
Heater stops unexpectedly Overheating, low fuel, low voltage, exhaust blockage. Check coolant level, refill fuel, check battery, clear exhaust pipe. Allow unit to cool down.
Insufficient heating Low fuel quality, clogged air filter, water pump malfunction, incorrect temperature setting. Use recommended fuel, clean/replace air filter, check water pump operation, adjust temperature settings.
Excessive smoke Poor combustion, incorrect fuel-air mixture, clogged exhaust. Check air intake and exhaust for blockages, ensure proper fuel quality. Professional inspection may be needed.

For more detailed troubleshooting, please consult the full manual or contact customer support.

11. User Tips

  • E-Mark Certification: Some users inquire about the presence of an 'E-number' on the part. The product is certified (E1 10 R-06 6738 is visible on the product label in images), indicating compliance with European vehicle regulations. Always verify local regulations for specific requirements.
  • Pre-season Test: It's advisable to run the heater for a short period before the onset of winter to ensure all systems are functioning correctly.
  • Fuel Type: Ensure you are using the correct fuel type (Diesel or Gasoline) as specified for your heater model.

12. Warranty and Support

For warranty information, technical support, or service inquiries, please refer to the contact details provided in your product packaging or reach out to the seller directly. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.