Introduction
This manual provides instructions for the Dtirszxy replacement remote control, designed for use with various Sherwood AV receivers and amplifiers. This remote offers a straightforward, no-programming-required solution for controlling your audio/video equipment.
Setup
1. Battery Installation
The remote control requires two (2) AA 1.5V Alkaline batteries (not included). Follow these steps to install them:
- Locate the battery compartment cover on the back of the remote control.
- Slide the cover downwards or press the latch and lift to open.
- Insert two AA batteries, ensuring the positive (+) and negative (-) terminals align correctly with the markings inside the compartment.
- Replace the battery compartment cover, sliding it back into place until it clicks securely.

2. Initial Use
This remote control is designed for immediate use with compatible Sherwood AV receivers and amplifiers. No programming or code entry is required. Simply install the batteries, point the remote at your device, and begin operation.
Operating Instructions
The remote control utilizes Infrared (IR) communication. Ensure a clear line of sight between the remote and your Sherwood AV receiver/amplifier for optimal performance.

Below is a general guide to the remote's functions. Button labels are typically self-explanatory.
| Button/Section | Function |
|---|---|
| POWER ON / STANDBY | Turns the AV receiver/amplifier on or off. |
| PARAMETER / SURROUND / STEREO | Selects audio parameters, surround sound modes, or stereo mode. |
| Numeric Keypad (0-9) | Direct input for channel selection or other numerical settings. |
| DIMMER / SLEEP | Adjusts display brightness or sets a sleep timer. |
| TEST / MUTE / VOLUME +/- | Initiates audio test, mutes/unmutes sound, or adjusts volume level. |
| AUDIO ASSIGN / SETUP / MAIN MENU | Accesses audio input assignments, system setup menus, or the main menu. |
| Directional Pad (Up, Down, Left, Right) / ENTER / RETURN / SEL | Navigates menus, confirms selections, or returns to previous screens. |
| DISPLAY / SEARCH M / CH.LEVEL / PRESET +/- | Controls display information, searches memory, adjusts channel levels, or navigates radio presets. |
| TUNE +/- / VIDEO 1-3 / BT.IN / AUX 1-2 / TUNER / CD / TAPE / TONE | Adjusts tuner frequency, selects various input sources (Video, Bluetooth, Auxiliary, Tuner, CD, Tape), or adjusts tone settings. |
| Playback Controls (NETWORK, Play, Pause, Stop, Skip, Fast Forward, Rewind) | Controls media playback functions for compatible devices or network sources. |
Maintenance
1. Cleaning
To clean the remote control, use a soft, dry cloth. For stubborn dirt, slightly dampen the cloth with water or a mild, non-abrasive cleaner. Do not use harsh chemicals or immerse the remote in liquids.
2. Battery Replacement
Replace batteries when the remote's range decreases or buttons become unresponsive. Always replace both batteries at the same time with new AA 1.5V Alkaline batteries. Do not mix old and new batteries, or different types of batteries.
3. Storage
If the remote control will not be used for an extended period, remove the batteries to prevent leakage and potential damage to the device.
Troubleshooting
- Remote not responding:
- Check if the batteries are inserted correctly with the correct polarity (+/-).
- Replace the batteries with fresh ones.
- Ensure there is a clear line of sight between the remote control and the AV receiver/amplifier. Obstructions can block the IR signal.
- Make sure the remote is pointed directly at the IR sensor on your AV receiver/amplifier.
- Verify that the AV receiver/amplifier is powered on.
- Some buttons do not work:
- This remote is a replacement and may not have all the exact functions of your original remote, or some functions might be mapped differently. Refer to your AV receiver/amplifier's original manual for specific functions.
- Clean the remote control, especially around the unresponsive buttons, to remove any dirt or debris that might be interfering.
Specifications
| Feature | Detail |
|---|---|
| Brand | Dtirszxy |
| Compatibility | Sherwood RD-606i, RD-6506, RC-138, RC-133, RC-139, RC-134, RD-6505 AV Receiver/Amplifier |
| Wireless Communication | IR (Infrared) |
| Frequency | 433 MHz (Note: While the product data mentions 433 MHz, the primary communication for this type of remote is typically IR. This frequency might refer to an internal component or a secondary, unused feature.) |
| Channel | 15 |
| Power Source | 2 x AA 1.5V Alkaline Batteries (not included) |
| Dimensions (Approx.) | Length: 10 cm, Width: 10 cm, Height: 10 cm |
| Weight (Approx.) | 0.24 kg |
| Support APP | No |
User Tips
- Line of Sight: For reliable operation, always ensure a direct, unobstructed line of sight between the remote control's IR emitter and the IR receiver on your Sherwood AV receiver/amplifier.
- Battery Quality: Using high-quality alkaline batteries can extend the remote's operational life and improve signal strength.
- Compatibility Check: While this remote is designed for the listed models, always cross-reference the button layout with your original remote or device manual if you encounter unexpected behavior.
Warranty and Support
For any questions, concerns, or support regarding this product, please contact the customer service of the seller. They will be able to assist you with troubleshooting or product-related inquiries.