1. Introduction
The HOTA D6 Ultra is a high-performance, dual-channel smart charger designed for a wide range of battery types, including LiPo, LiHV, Li-ion, NiZn, NiCd, NiMH, Smart Batteries, Lead Acid (Pb), and Eneloop. Featuring advanced GaN+SiC technology, it offers efficient and reliable charging with AC 300W and DC 650W power capabilities. Its compact design, intuitive UI, and comprehensive protection features make it an ideal choice for FPV drones, RC cars, airplanes, and other applications requiring precise battery management.
2. Key Features
- Dual Channel Output: Independent charging for two batteries simultaneously.
- High Power Output: AC 300W and DC 650W (2x 325W) for fast and efficient charging.
- Advanced GaN+SiC Technology: Utilizes gallium nitride and silicon carbide for higher efficiency, smaller size, and improved heat dissipation.
- Wireless Charging: Integrated wireless charging pad for compatible devices.
- Optimized User Interface: Simple and efficient UI for easy monitoring of charging status.
- Wide Voltage Input: Supports AC 100-240V and DC 6.5-30V, suitable for global use.
- Comprehensive Protection: Ten layers of protection including short circuit, overheat, overpower, reverse connection, capacity, time, low voltage, high voltage, overcurrent, and VO standard flame retardant material.
- High Balancing Current: Up to 1600mA per channel for precise cell balancing.
- Silent Operation: Low-speed fan design for reduced noise.
3. Setup and Connections
Before operating your HOTA D6 Ultra charger, ensure all connections are secure and correct.
- Power Input:
- For AC power, connect the AC power cable to the 'AC IN 100-240V' port on the rear of the charger and then to a wall outlet.
- For DC power, connect a DC power source (6.5-30V) to the 'DC IN 6.5-30V' port using the appropriate cable.
- Battery Connection:
- Connect your battery's main discharge plug to the 'OUT' port (Ch1 or Ch2) on the front of the charger.
- Connect the battery's balance lead to the corresponding 'Balance Port' (6S43210) for the selected channel.
- USB Output: The 'USB 5V/2.1A' port can be used for charging external devices.
- Update Port: The 'Update Port' is used for firmware updates.
- Wireless Charging: Simply place a compatible device on the top surface of the charger to initiate wireless charging.
4. Operating Instructions
The HOTA D6 Ultra features an intuitive UI for easy operation.
- Power On: After connecting the power source, the charger will power on and display the main interface.
- Channel Selection: Use the 'Channel Switch' button (CH) to select between Channel 1 and Channel 2.
- Navigation: Use the 'Speed Shuttle Key' (rotary knob) to navigate through menus and adjust parameters. Press the knob to confirm selections.
- Task/Setting: The 'Task' and 'Setting' buttons allow quick access to charging tasks and general charger settings.
- Charging Process:
- Select the desired battery type (LiPo, LiHV, etc.).
- Set the charge current (0.1-15A) and other parameters as required for your battery.
- Start the charging process. The display will show real-time voltage, current, power, and capacity.
- Discharge Functions: The charger supports internal discharge (15W x 2) and external discharge (325W x 2). Select the appropriate discharge mode and parameters from the menu.
- Wireless Charging: Place your Qi-compatible mobile phone or device on the designated wireless charging area on top of the charger. Charging will begin automatically.
5. Maintenance
- Cleaning: Use a soft, dry cloth to clean the charger's exterior. Do not use solvents or abrasive cleaners.
- Storage: Store the charger in a dry, cool environment, away from direct sunlight and extreme temperatures. The recommended storage temperature is -20°C to 60°C.
- Operating Environment: Ensure the charger is operated within the recommended temperature range of 0°C to 40°C. Adequate ventilation is crucial to prevent overheating.
- Cable Inspection: Regularly inspect all cables and connectors for any signs of wear or damage. Replace damaged cables immediately.
6. Troubleshooting
The HOTA D6 Ultra is equipped with multiple protection features. If an error occurs, the charger will typically display a warning message. Refer to the following for common issues:
- Charger Not Powering On:
- Check if the AC or DC input cable is securely connected.
- Ensure the power source is active and providing the correct voltage.
- Charging Error/Protection Triggered:
- Short Circuit Protection: Disconnect the battery immediately and check for any short circuits in the battery or cables.
- Overheat Protection: Ensure adequate ventilation around the charger. Allow it to cool down before resuming operation.
- Overpower Protection: Reduce the charging current or power settings if the input power source is insufficient.
- Reverse Connection Protection: Ensure battery polarity is correct before connecting.
- Low/High Voltage Protection: Verify battery voltage is within the charger's supported range.
- Overcurrent Protection: Check for any abnormal current draw; ensure settings match battery specifications.
- Capacity/Time Protection: These are user-set limits. Adjust them in the settings if necessary.
- Display Issues: If the screen is unresponsive or shows incorrect information, try restarting the charger.
7. Specifications
| Feature | Specification |
|---|---|
| Brand | HOTA |
| Product Name | D6 Ultra |
| Input Voltage | AC 100~240V / DC 6.5~30V |
| Balance Current | 1600mA x 2 |
| Charge Current | 0.1~15A x 2 |
| Discharge Current | 0.1~3A x 2 |
| Charge Power | DC 325W x 2 (@input voltage > 24V) / AC 300W (Support power distribution) |
| External Discharge Current | 1~15A x 2 |
| USB Output | 5V / 2.1A |
| Discharge Power | Internal: 15W x 2 (Balance port 10W x 2) / External: 325W x 2 (650W) |
| Storage Temperature | -20~60°C |
| Operating Temperature | 0~40°C |
| Battery Type | LiHv/LiPo/LiFe/Lilon/Lixx: 1~6S NiZn/NiCd/NiMH: 1~16S Smart Battery: 1~6S Lead Acid(Pb): 1~12S (2~24V) Eneloop: 1~16S |
| Screen Size | 2.8” 320x240 260000 colors |
| Dimensions | 108mm x 105mm x 76mm |
| Net Weight | 575g |
8. User Tips
- Always double-check your battery type and cell count settings before starting a charge cycle to prevent damage.
- Utilize the balance charging feature for LiPo/LiHV batteries to ensure cell voltage consistency and prolong battery life.
- Keep the charger's firmware updated to benefit from the latest features and improvements.
- For optimal performance and longevity, avoid operating the charger in dusty or humid environments.
9. Warranty and Support
For warranty information, technical support, or service inquiries, please refer to the documentation provided with your purchase or contact the seller directly. Keep your proof of purchase for warranty claims.