1. Introduction
The SkyRC OSH 6-Port 1S Lithium Battery Charging Hub is designed as a perfect companion for your B6neo series chargers. This hub allows you to safely and efficiently charge up to six micro 1S LiPo, LiFe, Li-ion, or LiHV battery packs simultaneously. It is available in two versions, supporting either BT2.0 or PH2.0 connectors, ensuring broad compatibility with various micro 1S battery styles.
2. Key Features
- 6-Port Charging: Simultaneously charges up to six 1S lithium battery packs.
- Broad Battery Compatibility: Supports LiPo, LiFe, Li-ion, and LiHV battery types.
- Connector Options: Available with either PH2.0 or BT2.0 plugs for versatile use.
- High Output Current: Maximum output current of 2.0A.
- Charger Compatibility: Designed to work seamlessly with SkyRC B6neo, B6ACneo, B6neo+, and B6neo 2 chargers.
- Compact Design: Lightweight and portable, ideal for FPV whoops and ultra-light trainers.
3. Setup Guide
To set up your SkyRC OSH 6-Port 1S Lithium Battery Charging Hub, follow these steps:
- Select the Correct Hub: Ensure you have the correct version (BT2.0 or PH2.0) that matches your battery connectors.
- Connect to Charger: Snap the OSH Charging Hub directly into the designated port on your compatible SkyRC B6neo series charger (B6neo, B6ACneo, B6neo+, or B6neo 2). The hub is designed to integrate securely with these chargers.
- Prepare Batteries: Ensure your 1S LiPo, LiFe, Li-ion, or LiHV batteries are in good condition and ready for charging.
4. Operating Instructions
Once the OSH Charging Hub is connected to your compatible SkyRC charger:
- Insert Jumper Cap: For proper cell detection and charging, insert the included jumper cap into the corresponding pins on the hub as per the number of cells to be charged. Refer to the markings on the hub (1-6) for guidance.
- Connect Batteries: Plug your 1S batteries into the available ports on the charging hub. You can charge up to six batteries simultaneously.
- Configure Charger: Set your SkyRC B6neo series charger to the appropriate battery type (LiPo, LiFe, Li-ion, or LiHV) and charging parameters (e.g., current, voltage) according to your battery manufacturer's recommendations. The hub facilitates parallel charging, so ensure your charger settings are suitable for the combined load.
- Start Charging: Initiate the charging process on your SkyRC charger. Monitor the charging progress as usual.
- Disconnect Batteries: Once charging is complete, safely disconnect the batteries from the hub, and then disconnect the hub from the charger.
5. Care and Maintenance
- Cleaning: Keep the charging hub clean and free from dust and debris. Use a soft, dry cloth for cleaning. Do not use liquid cleaners.
- Storage: Store the hub in a cool, dry place away from direct sunlight and extreme temperatures.
- Inspection: Regularly inspect the connectors and cables for any signs of wear, damage, or corrosion. Discontinue use if any damage is found.
- Avoid Moisture: Do not expose the hub to water or high humidity, as this can damage the electronic components.
6. Troubleshooting
- Hub Not Detected by Charger: Ensure the hub is securely connected to the charger. Check for any debris in the connection ports.
- Batteries Not Charging: Verify that the batteries are correctly plugged into the hub and that the jumper cap is inserted correctly for the number of cells. Confirm the charger settings match the battery type and desired charging parameters.
- Overheating: If the hub or batteries become excessively hot during charging, immediately disconnect them and investigate the cause. Ensure proper ventilation and correct charging settings.
- Damaged Connectors: If any battery or hub connectors appear damaged, do not use them. Replace damaged components to prevent short circuits or other hazards.
7. Specifications
| Parameter | Value |
|---|---|
| Battery Type | LiPo, LiFe, Li-ion, LiHV |
| Charger Supported | B6neo, B6ACneo, B6neo+, B6neo 2 |
| Output Current | Max. 2.0A |
| Charging Port | BT2.0 or PH2.0 (refer to SKU description for specific connector) |
| Jumper Cap | Insert it to the corresponding pins as per the cells to be charged |
| Working Temperature | 0°C ~ 40°C |
| Working Humidity | 5% ~ 75%RH non-condensing |
| Storage Temperature | -10°C ~ 70°C |
| Storage Humidity | 5% ~ 75%RH non-condensing |
| Weight | Approx. 20g |
| Dimension | 50.5 x 39 x 34.5mm |
8. User Tips
- Always double-check that the selected charging port type (BT2.0 or PH2.0) matches your batteries to avoid damage.
- Ensure the jumper cap is correctly positioned according to the number of cells in your battery pack for accurate charging.
- For optimal performance and safety, use only genuine SkyRC B6neo series chargers with this hub.
- When charging multiple batteries, ensure they are of the same type and similar state of charge for balanced parallel charging.
9. Warranty and Support
This product is manufactured to high-quality standards and is certified with CE, FCC, and RoHS. For any warranty claims, technical support, or service inquiries, please contact your original point of purchase or the manufacturer directly. Keep your proof of purchase for warranty validation.
