HORMANN BS Series BiSecur (HSE4-868-BS, HSE1, HSE2, HS1, HS4, HS5, HSD2, HSP4, HSS4)

Contents

HORMANN BS Series BiSecur Garage Remote Control User Manual

Models: HSE4-868-BS, HSE1, HSE2, HS1, HS4, HS5, HSD2, HSP4, HSS4

1. Product Overview

This manual provides instructions for the HORMANN BS Series BiSecur 868MHz garage remote control. It covers programming, reset procedures, and important compatibility information.

HORMANN BS Series BiSecur Garage Remote Control and compatible models.
Figure 1: HORMANN BS Series BiSecur Garage Remote Control and compatible models.

1.1 Package Contents

  • Remote Control
  • English Manual
  • Battery (included)
  • Keychain

2. Compatibility

This remote control is designed for use with HORMANN BS Series BiSecur systems operating at 868MHz. It is compatible with the following models:

  • HORMANN HS1-868-BS
  • HORMANN HS4-868-BS
  • HORMANN HS5-868-BS
  • HORMANN HSE1-868-BS
  • HORMANN HSE2-868-BS
  • HORMANN HSE4-868-BS
  • HORMANN HSP4-868-BS
  • HORMANN HSD2-868-BS
  • HORMANN HSS4-868-BS

Important Note on Encoding Method:

The factory default encoding method for this remote is Rolling Code (Blue LED). If your original remote control uses a Fixed Code (Red LED), this remote will NOT be compatible and will not work.

Diagram showing compatibility based on LED color: Red LED (Fixed Code) is not compatible, Blue LED (Rolling Code) is compatible.
Figure 2: LED Indicator for Encoding Method Compatibility.

Disclaimer:

It is not compatible with other remote controls not listed above. Please confirm your brand and model carefully before purchasing. The manufacturer is not responsible for incorrect purchases.

3. Setup and Programming

There are two primary methods for setting up your new remote control:

3.1 Cloning from an Original Remote (Rolling Code)

If your original remote is in working order and uses a Rolling Code (Blue LED), you can clone its code to the new remote.

  1. Prepare the New Remote: Press and hold the button on the new remote control where you intend to store the code. While holding it, press any other button 3 times. Continue holding the first button until the LED illuminates red for 10 seconds. Release all buttons.
  2. Illustration of programming step 1: Pressing and holding buttons on the new remote.
    Figure 3: Initializing the new remote for programming.
  3. Position Remotes: Place the original remote control to the left of the new remote, as close as possible (0-20 mm distance is ideal).
  4. Illustration of programming step 2: Placing original remote close to the new remote.
    Figure 4: Positioning remotes for cloning.
  5. Initiate Cloning: Press the button on the original remote control that you wish to program. Hold it until the LED on the new remote alternates flashing in red and blue. Check if the LED of the new remote is flashing blue. If not, try moving it closer to the original remote.
  6. Illustration of programming step 3: Pressing button on original remote, observing LED flashes.
    Figure 5: Activating cloning mode.
  7. Complete Learning: The learning procedure will be finished when the new remote's LED flashes rapidly in blue. Release all buttons.
  8. Illustration of programming step 4: New remote LED flashing blue, indicating successful learning.
    Figure 6: Successful cloning indication.
  9. Repeat for Other Buttons: Perform the same procedure for any remaining buttons you wish to program.

Video Tutorial:

Video 1: Step-by-step guide to programming the remote control.

3.2 Learning with Your Receiver (if Original Remote is Lost)

If your original remote control is lost, you can program the new remote directly with your receiver. The learning method is the same as for your original remote control. Refer to your receiver's manual for specific instructions on how to put it into learning mode.

Important:

If your receiver is in fixed code mode, you need to switch the remote control mode to fixed code (see section 3.4) before attempting to learn with the receiver.

3.3 Remote Control Reset Procedure

To assign a new radio code to each button of the remote control, follow these steps:

  1. Remove the battery for 10 seconds.
  2. Press and hold one button of the remote control.
  3. While holding the button, insert the battery. Observe the LED indicators:
    • The LED slowly flashes blue for 4 seconds.
    • The LED flashes quickly blue for 2 seconds.
    • The LED illuminates blue for a long time.
  4. Release the button. All radio codes are now newly assigned.

Note:

If the button is released prematurely during step 3, no new radio codes will be assigned.

3.4 Setting Remote to Fixed Code 868MHz Mode

This procedure is only necessary if your receiver operates on a fixed code system at 868MHz.

  1. Perform the Remote Control Reset Procedure (Section 3.3).
  2. Immediately after completing the reset (without releasing the button prematurely), continue pressing the button. Observe the LED indicators:
    • The LED slowly flashes blue for 4 seconds.
    • The LED flashes rapidly blue for 2 seconds.
    • The LED illuminates blue for a long time.
    • The LED slowly flashes red for 4 seconds.
    • The LED flashes rapidly red for 2 seconds.
    • The LED illuminates red for a long time.
  3. All radio codes are now newly assigned in Fixed Code 868MHz mode.

Note:

If the button is released prematurely during this process, the BiSecur (Rolling Code) radio code will remain active.

4. Operating Instructions

Once programmed, operate the remote control by pressing the corresponding button for your garage door or gate. The LED indicator will light up during transmission.

Special Note for "Type 2" Remote:

For the "Type 2" variant of this remote control, the button labeled "1" is for decoration only and does not have any functional purpose.

Image of Type 2 remote control highlighting the decorative button with no function.
Figure 7: Decorative button on Type 2 remote.

5. Maintenance

5.1 Battery Replacement

The remote control uses a standard battery (included). When the remote's range decreases or the LED indicator becomes dim, it's time to replace the battery. Refer to the device's casing for instructions on how to open it and replace the battery. Ensure correct polarity when inserting the new battery.

5.2 Care and Cleaning

Clean the remote control with a soft, dry cloth. Do not use abrasive cleaners or solvents. Keep the remote control dry and away from extreme temperatures.

6. Troubleshooting

  • Remote not programming (LED not flashing blue): Ensure the original remote is placed very close (0-20 mm) to the new remote during the cloning process.
  • New remote not working after programming:
    • Verify that your original remote uses a Rolling Code (Blue LED). If it uses a Fixed Code (Red LED), this remote is not compatible.
    • Ensure the programming steps were followed precisely. A premature release of buttons during reset or fixed code setting can prevent proper assignment of codes.
    • If programming directly with the receiver, confirm the receiver is in learning mode and the new remote is set to the correct code type (Rolling Code or Fixed Code 868MHz) as required by your receiver.
  • Reduced operating range: This typically indicates a low battery. Replace the battery as described in Section 5.1.

7. Specifications

FeatureDetail
BrandHORMANN
Encoding MethodRolling code (BiSecur)
Frequency868MHz, 868.3MHz, 868.35MHz
CertificationCE, FCC, RoHS, WEEE
OriginMainland China
Dimensions (L x W x H)8 cm x 8 cm x 8 cm (approximate package dimensions)
Weight0.06 kg (approximate package weight)

8. User Tips

  • Verify Compatibility: Always double-check that your existing remote control or receiver uses the BiSecur (Rolling Code) system and operates at 868MHz. If your original remote has a Red LED, this product is not compatible.
  • Proximity for Cloning: When cloning, ensure the new remote and the original remote are very close, ideally touching or within 20mm, to ensure successful signal transfer.
  • Patience During Programming: The LED indicators provide crucial feedback during programming. Observe them carefully and do not release buttons prematurely.
  • Decorative Button: If you have the "Type 2" remote, remember that the button labeled "1" is purely aesthetic and has no function.

9. Warranty and Support

For any issues or further assistance, please contact the seller or manufacturer directly. Keep your purchase records for warranty claims.

An additional user manual in PDF format may be available for download: View User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.