1. Introduction
The HamGeek Micro PA100+ Plus is an upgraded 100W HF QRP shortwave radio amateur power amplifier designed for portable and base station use. It features high-speed automatic transmission and reception switching, automatic LPF filter switching, and comprehensive protection mechanisms for power, standing wave ratio, and temperature. This manual provides essential information for the safe and effective operation of your device.
Key Improvements:
- New: ALC output (0 ~ -4V, compatible with ICOM and YAESU).
- Optimization: Reduced cooling fan noise.
- Optimization: Enhanced common mode interference suppression capability.
- Optimization: Improved stability with ultra narrowband antennas.
- Optimization: Consistent power across all frequency bands.
- Optimization: Full frequency input standing wave ratio.
- Optimization: Full frequency harmonic suppression.
- Optimization: Increased load capacity of the power supply circuit.
- Replacement: Larger 1.54-inch OLED display screen.
2. Product Overview
Familiarize yourself with the physical components of your HamGeek Micro PA100+ Plus amplifier.
Figure 2.1: Front view of the amplifier with included power cable.
Figure 2.2: Close-up of the front panel showing the OLED display, cooling fan, and FN button.
Figure 2.3: Rear view of the amplifier with ACC, DC IN, TRX, and ANT connectors.
Figure 2.4: Close-up of the rear panel showing ACC (3.5mm jack), DC IN (XT60 connector), TRX (SO-239), and ANT (SO-239) ports.
Figure 2.5: Side view of the amplifier.
Figure 2.6: Top view of the amplifier.
3. Setup and Initial Calibration
Reminder! Operate with caution!
The following steps describe the initial setup and calibration process for the HamGeek PA100+ Plus. This process involves internal adjustments and requires careful attention.
- Open the Case and Power On: Carefully open the HamGeek PA100+ Plus case and connect the power supply.
- Activate TX State: Locate the 1.25mm socket inside the unit. Use a wire or tweezers to connect the "PTT" and "GND" points. This can be done on the plug itself or directly on the PCB. Once connected, the HamGeek PA100+ Plus should enter the TX (transmit) state.
- Calibrate Pin 1 Voltage:
- Using the DC voltage range of a multimeter, measure the voltage between the pin marked "1" (refer to the internal PCB diagram, not provided as an image but described in the original manual) and a GND point (e.g., a screw).
- Adjust the adjustable potentiometer marked "1" clockwise until the voltage of pin 1 is between 3.95V and 4.1V.
- Calibrate Pin 2 Voltage:
- Using the DC voltage range of a multimeter, measure the voltage between the pin marked "2" (refer to the internal PCB diagram) and a GND point (e.g., a screw).
- Adjust the adjustable potentiometer marked "2" clockwise until the voltage of pin 2 is between 3.95V and 4.1V.
- Ensure the voltage for pin 2 is consistent with pin 1 (e.g., both are 4.0V).
- Finalize Setup: Disconnect the power supply, remove the connecting wires from "PTT" and "GND", and securely re-install the housing.
Optional Modification:
After performing the above calibration, the gain of the HamGeek PA100+ Plus will increase. For advanced users, the feedback resistor can optionally be changed from the original 330Ω to 100Ω. This modification is not required for normal operation.
4. Operating Instructions
The HamGeek Micro PA100+ Plus is designed for ease of use with several intelligent features:
- Automatic TX/RX Switching: The amplifier features high-speed automatic transmission and reception switching. With RF triggering, it can automatically switch between transmit and receive states even without a PTT SEND signal from your transceiver.
- Automatic LPF Filter Switching: The unit automatically switches the appropriate Low Pass Filter (LPF) without needing an ACC control line. It includes 5 sets of 5th order LPFs covering all HAM dedicated shortwave communication frequency ranges from 80 meters to 10 meters.
- Power and Standing Wave Protection: The amplifier includes display and protection mechanisms for output power and standing wave ratio (SWR). This ensures reliable equipment safety, especially under poor antenna conditions, preventing damage.
- Wide Voltage Range & Protection: Designed for a wide voltage input range (10V-15V), it also features voltage display and protection, making it convenient and safe for outdoor use with lithium battery power supplies.
- Temperature Management: Integrated temperature display and protection, along with intelligent dual-fan cooling, ensure optimal operating temperatures and prevent overheating.
- Semi-Insert Mode: This function allows for semi-insert operation even without connecting a PTT SEND line.
- Band Switching Protocols: The amplifier supports band switching protocols for ICOM, YAESU, and XIEGU transceivers. Note that an ACC control cable connection is required for this feature.
5. Maintenance
To ensure the longevity and optimal performance of your HamGeek Micro PA100+ Plus, follow these maintenance guidelines:
- Cleaning: Keep the amplifier clean and free from dust. Use a soft, dry cloth for external cleaning. Avoid using harsh chemicals or abrasive materials.
- Ventilation: Ensure the cooling fan and ventilation openings are clear of obstructions to allow for proper airflow. Regularly check for dust buildup in the fan area and gently clean if necessary.
- Connections: Periodically check all cable connections (power, antenna, transceiver) to ensure they are secure and free from corrosion.
- Storage: When not in use for extended periods, store the amplifier in a cool, dry place, away from direct sunlight and extreme temperatures.
6. Troubleshooting
This section provides solutions to common issues you might encounter:
- No Power:
- Check the power cable connection to the amplifier and the power source.
- Verify that the power supply voltage is within the specified range (10V-15V).
- Ensure the power supply can deliver sufficient current (up to 18A).
- Low Output Power:
- Confirm the input power from your transceiver is within the recommended range (≤ 8W, MAX 10W). Output power is directly related to input power.
- Check antenna SWR. High SWR can trigger protection circuits and reduce output.
- Ensure the supply voltage is adequate; lower voltage will result in lower output power.
- High SWR Warning/Protection:
- Inspect your antenna system for proper connection, tuning, and condition.
- Ensure the antenna is suitable for the operating frequency.
- Check all coaxial cable connections for shorts or open circuits.
- Overheating/Temperature Protection:
- Ensure the cooling fan is operating and not obstructed.
- Verify adequate ventilation around the amplifier.
- Reduce transmit duty cycle or input power if operating in high ambient temperatures.
- Display Issues:
- If the OLED display is not functioning, check power connections.
- If the display is dim or shows incorrect information, power cycle the unit.
7. Specifications
| Feature | Specification |
|---|---|
| Frequency Range | 3.5MHz - 30MHz |
| Input Power | ≤ 8W (MAX 10W) |
| Output Power | 100W ±1.5dB at 13.8V (Note: Input power determines output power) |
| Output Impedance | 50 ohm |
| Supply Voltage | 10V-15V; 13.8V (typical value) (Note: Lower voltage will provide lower power output) |
| Current Consumption | ≤18A |
| Working Temperature | ≤55℃ |
| Dimensions (excluding protrusions) | 125 x 51 x 180 mm |
| Dimensions (including protrusions) | 132 x 58 x 198 mm |
| Weight | Approximately 1.15 kg |
8. User Tips
While specific user reviews or Q&A were not available for this manual, general tips for operating amateur radio equipment include:
- Power Supply Quality: Always use a stable and clean power supply capable of delivering the required current to avoid performance issues or damage.
- Antenna Matching: Ensure your antenna is well-matched to the operating frequency to minimize SWR and maximize power transfer. A low SWR is crucial for amplifier longevity.
- Ventilation: Provide ample space around the amplifier for proper air circulation, especially during prolonged transmissions, to aid the cooling system.
- Cable Quality: Use high-quality coaxial cables and connectors to minimize signal loss and ensure reliable operation.
9. Warranty and Support
For warranty information, technical support, or service inquiries, please contact your retailer or the manufacturer directly. Keep your proof of purchase for warranty claims.
A detailed user manual in PDF format is available for download: HamGeek Micro PA100+ Plus User Manual (PDF).