SR SUNTOUR X1

Contents

SR SUNTOUR X1 Bicycle Suspension Fork User Manual

Model: X1 | Brand: SR SUNTOUR

1. Introduction

Thank you for choosing the SR SUNTOUR X1 Bicycle Suspension Fork. This manual provides essential information for the safe installation, operation, and maintenance of your new suspension fork. Please read it thoroughly before installation and use to ensure optimal performance and rider safety.

Important Note on Branding: While this product is branded as SR SUNTOUR, some general instructional materials may reference 'NANLIO' forks. The instructions provided herein are applicable to your SR SUNTOUR X1 fork, focusing on its features and specifications.

2. Safety Information & Warnings

This product complies with ISO 4210 Safety Standards.

WARNING:

  • Installation Safety: Improper installation of the fork can cause damage to the bicycle or loss of control, leading to serious injury or death. We strongly recommend having this product installed by a professional bicycle mechanic.
  • Check Before Every Ride: Always inspect your fork for any cracks, dents, oil leaks, or loose parts before riding. Do not ride if any damage is found.
  • Intended Use: This fork is designed for Cross Country (XC) and Trail riding. DO NOT use for Freeride, Downhill, Dirt Jumping, or other extreme gravity sports. Misuse voids the warranty and risks failure.
  • Brake Compatibility: Ensure your brake system (Disc or V-brake) is compatible with the fork mounts. Check brake tightness regularly.

3. Components Overview

Familiarize yourself with the key components of your SR SUNTOUR X1 suspension fork.

SR SUNTOUR X1 Suspension Fork main features
Figure 3.1: SR SUNTOUR X1 Suspension Fork highlighting 120mm travel, QR 100x9MM & BOOST 110x15MM, 27.5/29 inch compatibility, air fork, manual/remote lockout, and 32mm stanchions.
Detailed view of fork features: disc brake mounting post, aluminum alloy hook, wire clip
Figure 3.2: Detailed view of fork features including the 74mm disc brake mounting post (international A-pillar standard), aluminum alloy hook for smooth braking, and a detachable wire clip for convenient fixation.
Wire Clip and Air Chamber Switch details
Figure 3.3: Close-up of the wire clip and the air chamber switch, which allows adjustment of the fork's soft/hard effect by adding or reducing air pressure.

4. Specifications

The SR SUNTOUR X1 fork is available in various configurations. Please refer to the specific model you have for exact details.

General Specifications:

AttributeValue
Brand NameSR SUNTOUR
Model NumberX1
UseMountain Bikes
Fit ForDisc Brake
SuspensionYes
MaterialAlloy (Magnesium alloy for fork leg, Aluminum alloy for fork shoulder and inner tube)
OriginMainland China

Dimensional Specifications:

Dimensional diagram for 27.5 Inch-120MM and 29 Inch-100MM forks
Figure 4.1: Dimensional comparison between 27.5 Inch-120MM and 29 Inch-100MM fork models.
Measurement27.5 Inch-120MM29 Inch-100MM
Steerer Tube DiameterΦ28.6mmΦ28.6mm
Crown DiameterΦ30mmΦ39.8mm
Stanchion DiameterΦ32mmΦ32mm
Actual Length130mm110mm
Fork Length520mm510mm
Lower Leg DiameterΦ38mmΦ38mm
Axle Width100x9mm100x9mm

XCR-BOOST Fork Specifications:

Specifications for XCR-BOOST FORK
Figure 4.2: Detailed specifications for the XCR-BOOST Fork model.
AttributeValue
BrandSR SUNTOUR
BrakeDISC BRAKES
StructureOil Spring Fork
Bottom gearΦ30MM
Top tubeΦ28.6MM
Pipe diameterΦ34MM
THRU lever110x15MM
Size29INCH
Stroke height120MM
ModelXCR
MaterialMagnesium alloy (fork leg) Aluminum alloy (fork shoulder and inner tube)
StyleTapered Manual (Tape damping)

QR Fork Specifications:

Specifications for QR FORK
Figure 4.3: Detailed specifications for the QR Fork model.
AttributeValue
BrandSR SUNTOUR
BrakeDISC BRAKES
StructureOil Spring Fork
Bottom gearΦ30MM
Top tubeΦ28.6MM
QR lever100x9MM
Size27.5/29INCH
Stroke height100MM/120MM
ModelX1
MaterialMagnesium alloy (fork leg) Aluminum alloy (fork shoulder and inner tube)
StyleStraight Manual/Remote tapered Manual/Remote (Tape damping/undamped)

X1-BOOST Fork Specifications:

Specifications for X1-BOOST FORK
Figure 4.4: Detailed specifications for the X1-BOOST Fork model.
AttributeValue
BrandSR SUNTOUR
BrakeDISC BRAKES
StructurePneumatic front fork (Air Fork)
Bottom gearΦ30MM
Top tubeΦ28.6MM
Pipe diameterΦ32MM
THRU lever110x15MM
Size27.5/29INCH
Stroke height120MM
ModelX1
MaterialMagnesium alloy (fork leg) Aluminum alloy (fork shoulder and inner tube)
StyleTapered Manual (Tape damping)

5. Installation Instructions

Follow these steps carefully for proper installation. Professional installation is recommended.

  1. Preparation: Remove the old fork and headset race. Clean the head tube of the frame. Ensure the headset bearings are in good condition.
  2. Install Crown Race: Install the correct crown race (compatible with your headset) onto the base of the fork steerer tube. Ensure it sits flush against the crown.
  3. Cut Steerer Tube (If necessary):
    • Measure twice! Mark the cutting line based on your stem and spacer stack height.
    • Use a proper saw guide to ensure a square cut.
    • File off sharp edges after cutting to prevent injury and damage to the stem.
  4. Install Star Nut / Expander Plug: Install the star nut into the steerer tube using a star nut setting tool. It should be recessed 10-15mm below the top edge.
  5. Final Assembly:
    1. Slide the fork into the frame head tube.
    2. Install stem and spacers.
    3. Tighten the top cap bolt to preload the headset bearings (remove play, but allow smooth rotation).
    4. Align the stem with the front wheel and tighten the stem clamp bolts to the manufacturer's specified torque (typically 5-6 Nm).

      Warning: Do not overtighten stem bolts, as this may crush the steerer tube.

  6. Wheel & Brake Installation: Install the front wheel ensuring the axle (Quick Release or Thru-Axle) is securely tightened. Install the brake caliper. Align it with the rotor and tighten bolts to torque specs (typically 6-8 Nm). Route the brake hose through the cable guide.

6. Operation

Air Pressure (For Air Forks Only):

Remove the air valve cap (usually on the left leg). Use a high-pressure shock pump to adjust sag to 15-20% of total travel based on your body weight. Only applicable to air forks. Use a high-pressure shock pump to adjust the preload to the desired stroke (15-20%).

Lockout Function:

Manual Lock vs Remote Lock
Figure 6.1: Comparison of Manual Lock and Remote Lock features.
  • Open: For rough terrain and descending.
  • Lock: For climbing or smooth pavement roads to improve efficiency.

Note: Do not use the lockout feature on rough descents.

Damping Rebound Adjustment:

Damping Rebound Adjustment System
Figure 6.2: Damping Rebound Adjustment System, showing -Slow Rebound and +Fast rebound settings.

The damping rebound adjustment system allows you to increase or decrease rebound speed, making it easier to handle off-road conditions. Adjust the dial towards '-' for slower rebound and towards '+' for faster rebound.

7. Maintenance

  • After Every Ride: Wipe dust and mud off the stanchion tubes (inner legs) and wiper seals using a soft microfiber cloth.
  • Every 50 Hours: Check all bolts for proper torque. Inspect the stanchions for scratches.
  • Cleaning: Use mild soapy water. Do not use high-pressure washers, as water may enter the seals and damage internals.

8. Troubleshooting

Rebound Adjustment Dial Loose/Detached:

If the rebound adjustment dial becomes loose or detached, it may affect the fork's damping performance. This issue typically requires re-securing or replacing the dial. If you are not comfortable performing this repair, it is recommended to seek assistance from a professional bicycle mechanic.

9. User Tips

  • Many users appreciate the quality and performance of this fork, noting its smooth operation and effective damping.
  • Be aware that some models are air forks, while others are oil spring forks. Confirm your specific model's type for appropriate setup and maintenance.
  • The fork is praised for its robust construction, often featuring aviation-grade aluminum alloy for high strength.

10. Warranty & Support

SR SUNTOUR warrants this product to be free from defects in materials and workmanship for a period of one year from the date of purchase. The warranty does not cover normal wear and tear, improper installation, lack of maintenance, or damage caused by accident or misuse.

Additional Resources:

For further detailed information and diagrams, you may refer to the general user manual PDF available here. Please note that this PDF may reference a different brand (NANLIO) but contains relevant technical instructions.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.