ETENWOLF S0

Contents

ETENWOLF S0 Mini Portable Electric Bike Tire Pump User Manual

Model: S0

Brand: ETENWOLF

1. Introduction

The ETENWOLF S0 Mini Portable Electric Bike Tire Pump is a compact and powerful cordless inflator designed for various inflation needs, primarily bicycles. It features a digital display, auto shut-off, and a 2400mAh battery, offering convenience and precision for on-the-go inflation.

Please read all instructions and safety warnings before use to ensure proper operation and to reduce the risk of electric shock, fire, and/or serious injury.

2. Package Contents

Verify that all the following items are included in your package:

  • Mini Bike Pump (S0) x1
  • Air Chuck (Schrader Valve) x1
  • Cone shaped nozzle x1
  • Ball needle x1
  • French copper adapter x1
  • T-shaped quick connector x1
  • User Manual x1
ETENWOLF S0 Mini Bike Pump and included accessories
The ETENWOLF S0 Mini Bike Pump with its various accessories, including different nozzles and a storage bag.

3. Product Overview

Familiarize yourself with the components of your ETENWOLF S0 Mini Bike Pump:

  1. Power On/Off Button: Controls power and inflation start/pause.
  2. "+" Pressure Increase Button: Increases target pressure.
  3. "-" Pressure Decrease Button: Decreases target pressure.
  4. High-pressure Hose: Connects the pump to the item to be inflated.
  5. Target Input/Actual Pressure Display: Shows the set pressure and current pressure.
  6. Battery Indicator: Shows remaining battery level.
  7. Pressure Unit Display: Indicates the current pressure unit (PSI/BAR).
  8. Type-C Port: For charging the device.
ETENWOLF S0 Mini Bike Pump digital display showing 150 PSI and accuracy
The pump's digital display showing the target pressure and its ±1psi accuracy.

Note: The power-on screen shows the target input value for 2 seconds, then displays the actual pressure.

4. Setup and Operating Instructions

4.1. Quick Start Guide for Inflation

  1. Connect the Nozzle: Screw the nozzle end of the high-pressure hose clockwise into the valve of the object to be inflated.
  2. Turn On: Press the Power On/Off Button to turn on the pump.
  3. Adjust Pressure Unit: Press the "+" and "-" buttons together to switch between PSI and BAR units.
  4. Set Target Pressure: Use the "+" and "-" buttons to increase or decrease the desired pressure value.
  5. Start Inflation: Press the Power On/Off Button again to start inflation.
  6. Automatic Stop: The pump will automatically stop when the preset pressure is reached.
Step-by-step guide for inflating a tire with the ETENWOLF S0 pump
Visual guide for the inflation process.

4.2. Important Notes for Operation

  • To stop inflation at any time, press the Power On/Off Button.
  • When used again, the system will automatically recall the previous pressure setting.
  • Double-check the target pressure setting. Incorrect values may cause the item to explode.
  • After inflation, the internal tire temperature drops to ambient temperature, which may reduce pressure by 0.5-1.5 psi.
  • After inflating a bicycle tire, quickly remove the hose to avoid air leakage that may reduce tire pressure.

4.3. Checking Current Pressure

  1. Connect the nozzle end of the hose to the object to be measured.
  2. Press the Power On/Off Button to turn on.
  3. The screen will display the current pressure value.

4.4. Power On/Pause Button Functions

  • Turn On: Long press the Power On/Off Button for 0.5 seconds.
  • Turn Off: When the pump is on, long press the Power On/Off Button for 2 seconds.
  • Pause: When the pump starts inflating, press the Power On/Off Button again at any time to pause.

4.5. Automatic Shut-Off Conditions

The pump will shut off automatically in the following cases:

  • The charging cable is accidentally disconnected.
  • The battery runs out.
  • After 5 minutes of inactivity following a full charge.

4.6. Pressure Memory Setting

Each time you adjust the pressure, the system will remember your new target and unit. You can change the default at any time.

5. Battery Charging and Indicators

5.1. Charging Instructions

For optimal charging performance and stability, use a certified PD charger and the included charging cable. Charging from 0% to 100% takes approximately 1-2 hours. Fully charge the pump before first use.

5.2. Battery Indicator (Discharging)

  • 0-10%: Orange light blinking
  • 10-20%: Orange light solid
  • 20-100%: White light solid

5.3. Battery Indicator (Charging)

  • 0-20%: Orange light blinking
  • 20-99%: White light blinking
  • 100%: White light solid

Note: The pump will auto shut down after 5 minutes of inactivity when fully charged. It cannot be used while charging.

Internal view of ETENWOLF S0 pump showing 2400mAh battery and inflation capacity
The pump features a 2400mAh battery, capable of refilling 26 bicycle tires (80-100 PSI) or inflating 8 bicycle tires from 0-100 PSI.

6. Pressure Calibration

Different altitudes can cause pressure changes of 1-3 psi. In high altitude areas (especially over 5000 ft / 1524 m), users can recalibrate the pump's sensor.

6.1. Calibration Steps

  1. Press the Power On/Off Button.
  2. Hold both "+" and "-" buttons for 5 seconds.
  3. When the display blinks, calibration is successful.

6.2. Calibration Notes

  • Turn on the device before starting calibration.
  • The high-pressure hose must not be connected to anything during calibration, or it will fail.
  • Sufficient power or an external source is needed for calibration.
  • No memory for new calibration settings. Once powered off, it resets to sea level (0 ft/m).
  • Above 5000 ft / 1524 m, manual calibration is needed each time the pump is turned on.

7. Maintenance

  • Store the product within the temperature range of -4°F to 140°F (-20°C to 60°C). Extremely hot or cold environments can damage the battery and shorten the pump's lifespan.
  • For long-term storage, charge the pump at least once every three months to maintain good performance and battery efficiency.
  • Keep the product away from heat sources and do not leave it in a hot car for long periods to prevent overheating.
  • Use this product in a dry, clean environment. Dust intrusion may damage the product.
  • Do not clean the product with water.
  • To reduce the risk of electric shock, do not expose the device to rain; store it indoors.

8. Troubleshooting

ProblemSolution
Inflation is slowCheck for leaks in the hose; ensure battery is charged.
Pump is on but not inflatingCheck if target pressure exceeds preset value.
Battery indicator doesn't show after chargingUse certified PD charger and try again.
Pump stopped due to extreme temperatureWhile charging, temperature must be 0°C-45°C (32°F-113°F). While inflating/deflating, temperature must be -20°C–74°C (-4°F–165°F).
Safety alert symbol lights up if abnormal pressure or motor errorTurn off the unit and restart after 10 minutes.
Pump is working but pressure reads zeroIf pressure <3 PSI, display shows 0 due to sensor limits.
Battery indicator varies from standby during useLithium battery voltage drops under load, causing this; it's normal.
Safety symbol shows E08If issue persists after reboot, contact factory for repair.
Displays error code E10Motor failure warning. May recover after blinking 30 sec. If not, send for repair.
Displays error code E11Low-temp charge icon: charging temp too low. Warm to above 0°C before charging.
Displays error code E12High-temp charge icon: let temp drop below 45°C before charging.
Displays error code E13Low-temp discharge icon: warm to >-20°C before use or charging others.
Displays error code E14High-temp discharge icon: cool below 58°C before use or output charging.
Display error code E15The air pump has exceeded the working time, the warning icon flashes for 30 seconds then returns to normal. Check if the inflated item is leaking.
Display error code E16Overpressure protection icon, returns to normal after releasing pressure.
Display error code E17High-pressure operation has exceeded working time, warning icon flashes for 30 seconds then returns to normal. Check if the inflated parts are functioning abnormally.
Display error code E18Battery damage warning icon and battery level indicator icon flash. After 30 seconds, the device will shut down. It is necessary to send the device to the factory.

9. Specifications

FeatureDetail
NameBicycle Pump
ModelS0
Size94.8 x 75.2 x 40.2 mm
Inflation pressure range3.0-150.0 PSI / 0.20-10.34 bar
Operating temperatureCharging: 32°F~113°F (0°C~45°C), Discharging: -4°F~165°F (-20°C~74°C)
Storage temperature-4°F~140°F (-20°C~60°C)
High-pressure hose length88 mm
Battery capacity2400 mAh (8.88 Wh)
Operating noisebelow 85 dB within 1 meter range
InputType-C: 5V 2A
Working durationAbout 15 minutes at 25°C ambient temperature, within 20-50 PSI inflation pressure range
Charging time1-2 Hours
Sensor accuracy±1 psi
Recommended pressure ranges for different items
Recommended pressure ranges: Bicycles (25-100 psi), Motorcycles (28-42 psi), Basketballs (4-13 psi).

10. Safety Instructions

  • This product is not a toy and is not suitable for children. Users must be at least 16 years old. Keep children at a safe distance from the pump during inflation.
  • The product contains a built-in lithium battery. Do not throw the product into fire or dispose of the battery improperly.
  • Overheating damage or water ingress may increase the risk of fire or explosion. It is best to keep the product away from heat sources and not leave it in a hot car for long periods. If the pump becomes very hot, it may explode.
  • Please store the product within the temperature range of -4°F to 140°F (-20°C to 60°C). Extremely hot or cold environments can damage the battery and shorten the pump's lifespan. Long-term storage can reduce battery efficiency. Charge the pump at least once every three months to maintain good performance.
  • This product contains a built-in DC motor, which may produce sparks during use. Do not use in environments with explosive dust or gas.
  • If there is unusual noise or the temperature becomes very high during inflation, please turn off the pump immediately.
  • Before setting the inflation pressure, please ensure the correct pressure unit is selected. Mixing PSI and BAR may cause over-inflation and explosion.
  • Unit conversion: 1 bar = 14.5 psi, 1 bar = 100 kPa.
  • Do not leave the pump unattended while operating.
  • Use this product in a dry, clean environment. Dust intrusion may damage the product. Do not clean the product with water.
  • Always use a certified PD charger and the included charging cable to charge this product.
  • To reduce the risk of electric shock, do not expose the device to rain; store it indoors. Failures caused by not following these requirements are not covered by the warranty.
ETENWOLF S0 pump with safety protection icons
The pump includes multiple safety protections: low voltage, overcharge, overcurrent, short circuit, and temperature protection.

11. User Tips

  • The brushless motor design contributes to a quieter operation compared to other mini pumps.
  • Its very small and compact size makes it ideal for carrying on a bike or in a small bag.

12. Frequently Asked Questions (FAQ)

Q: How long does it take to fully charge the pump?
A: It takes approximately 1-2 hours to fully charge the pump from 0% to 100% using a certified PD charger and the included cable.
Q: Can I use the pump while it is charging?
A: No, the pump cannot be used while charging.
Q: What should I do if the pump stops due to extreme temperature?
A: If the pump stops due to high temperature during inflation/deflation, let it cool down to below 74°C (165°F). If it stops due to low temperature, warm it up to above -20°C (-4°F) before use. For charging, ensure the temperature is between 0°C and 45°C.

13. Warranty and Support

13.1. Warranty Information

Within two years of purchase, we provide timely and effective online after-sales service. We will repair or replace any defective product (due to manufacturing faults) within the warranty period. Failures caused by not following the safety and usage requirements are not covered by the warranty.

13.2. Manufacturer and Brand Owner

Manufacturer: Guangdong Bestek Technology Co., Ltd
Address: No.1, North Gaopu 8th Road, Yuancheng Industrial Park, Heyuan City, Guangdong, P.R.China

Brand owner: Mozhen Technology (Shenzhen) Co., LTD
Address: CN-503, Floor 5, Building 4, Tianan Yungu Industrial Park Phase II, Gangtou Community, Bantian Street, Longgang District, Shenzhen, Guangdong, CN

13.3. Contact Support

For any questions, comments, or after-sales inquiries, please contact us:

We are committed to providing you with professional and efficient service!

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.