wishiot JC3248W535C

Contents

User Manual

ESP32-S3 3.5 inch Capacitive Touch Display Module

Model: JC3248W535C | Brand: wishiot

1. Introduction

This manual provides detailed instructions for the setup, operation, maintenance, and troubleshooting of your ESP32-S3 3.5 inch Capacitive Touch Display Module (Model: JC3248W535C). This module features an ESP32-S3-WROOM-1 as its main control, integrating Wi-Fi and Bluetooth functionalities, and is designed for various development applications including Arduino IDE, ESP IDE, Micropython, and Guition.

2. Features

  • 3.5-inch color screen supporting 16-bit RGB 65K color display for rich visuals.
  • 320x480 resolution for clear image output.
  • Pre-programmed sample program for immediate plug-and-play functionality.
  • Integrated TF card slot for expanded storage capabilities.
  • Arduino library functions and sample programs provided to facilitate rapid secondary development.
  • Lithium battery charging and discharging circuit with overcharging and discharging protection.
  • Up to 12 available I/O pins for custom applications.
  • Supports one-click program download.
  • Built to military-grade process standards for long-term stable operation.

3. Specifications

ParameterValue
Main ControlESP32-S3-WROOM-1 (Dual-core MCU)
Integrated FeaturesWI-FI, Bluetooth
Main FrequencyUp to 240MHz
SRAM512KB
ROM384KB
PSRAM8MB
Flash Size16MB
Display ColorRGB 65K color
SKUCapacitive touch: JC3248W535C_I_Y
Display Size3.5 inch
Display TypeTFT IPS
Driver ChipAXS15231B
Resolution320x480 pixels
Effective Display Area73.4 x 49.0 mm
Module Size94.5 x 62.0 mm
Operating Temperature-20℃ to 70℃
Storage Temperature-30℃ to 80℃
Operating Voltage5V
Power ConsumptionAbout 150mA
Product WeightAbout 80g
Front view of the ESP32-S3 3.5 inch Capacitive Touch Display with dimensions and example UI icons.

Figure 1: Front view with module dimensions (94.5mm x 62.0mm) and effective display area (73.4mm x 49.0mm).

4. Setup Guide

This section outlines the physical connections and initial software setup for your display module.

4.1 Physical Connections

Refer to Figure 2 for the layout of connectors and buttons on the back of the module.

  • Power Supply: Connect a 5V power source via the Type-C USB port or the JST1.25 4P Power connector.
  • Battery Connection: For portable applications, connect a compatible lithium battery to the JST1.25 2P Battery connector. Ensure the Battery switch button is in the correct position.
  • I/O Expansion: Utilize the JST1.25 8P IO port and HC1.0 4P for connecting external sensors, actuators, or other peripherals. Up to 12 IOs are available.
  • Speaker Output: Connect an external speaker to the "Speak" connector for audio output.
  • TF Card: Insert a TF card into the designated slot for expanded storage.
Back view of the ESP32-S3 module showing labeled connectors: Battery switch button, JST1.25 2P Battery connector, Type-C port, JST1.25 4P Power, Boot button, Reset button, HC1.0 4P, JST1.25 4P, JST1.25 8P IO port, and Speak connector.

Figure 2: Back panel layout with labeled connectors and buttons.

4.2 Software Setup (Arduino IDE Example)

The module supports development with Arduino IDE, ESP IDE, Micropython, and Guition. For Arduino IDE:

  1. Install the Arduino IDE on your computer.
  2. Add the ESP32 board manager URL to your Arduino IDE preferences.
  3. Open the Boards Manager (Tools > Board > Boards Manager...) and search for "ESP32" to install the necessary board definitions.
  4. Select "ESP32S3 Dev Module" from the Tools > Board > ESP32 Arduino menu.
  5. Connect the module to your computer via the Type-C USB port.
  6. Select the correct COM port under Tools > Port.
  7. You can now upload your Arduino sketches to the module. Sample programs and library functions are provided to facilitate development.
Screenshot of Arduino IDE showing the 'ESP32S3 Dev Module' selected under the Tools > Board menu.

Figure 3: Selecting the ESP32S3 Dev Module in Arduino IDE.

5. Operating Instructions

The module comes with a pre-programmed sample program that allows for immediate use upon powering on. This program typically demonstrates basic display and touch functionalities.

  • Power On: Connect the module to a 5V power source. The display should light up and show the pre-programmed interface.
  • Capacitive Touch: Interact with the display using light touches, similar to a smartphone screen. The capacitive touch screen allows for intuitive user input.
  • TF Card Usage: If your application requires additional storage for images, videos, or data, insert a formatted TF card into the slot. Ensure your program is configured to read from or write to the TF card.
  • Custom Programming: For advanced functionalities, develop your own applications using the supported IDEs (Arduino IDE, ESP IDE, Micropython, Guition) and upload them to the module. The "Boot" and "Reset" buttons may be used during the programming process as per the specific development environment's instructions.
The ESP32-S3 display module showing a vibrant image, demonstrating its visual capabilities.

Figure 4: Example of display output.

6. Maintenance

  • Cleaning: Use a soft, dry, lint-free cloth to clean the display surface. Avoid using abrasive cleaners or solvents that could damage the screen or casing.
  • Environmental Conditions: Operate the module within the specified operating temperature range of -20℃ to 70℃. Store it within -30℃ to 80℃. Avoid exposure to extreme humidity, direct sunlight, or corrosive environments.
  • Power Management: If using a lithium battery, ensure proper charging and discharging practices. The module includes built-in overcharging and discharging protection.
  • Physical Handling: Handle the module with care to prevent physical damage to the screen or connectors. Avoid applying excessive force to the display.

7. Troubleshooting

Display not turning on:
  • Ensure the 5V power supply is correctly connected and functional.
  • If using a battery, check its charge level and ensure the battery switch is in the ON position.
  • Verify that the Type-C cable is securely connected to both the module and the power source/computer.
Touch screen unresponsive:
  • Check for any physical obstructions or debris on the screen surface.
  • Ensure your software application is correctly configured to handle touch input.
  • Try resetting the module using the "Reset" button.
Program upload failure:
  • Verify that the correct board ("ESP32S3 Dev Module") and COM port are selected in your IDE.
  • Ensure all necessary drivers for the ESP32-S3 are installed on your computer.
  • Check the USB cable for damage and try a different port.
  • Follow the specific programming instructions for your chosen IDE, which may involve pressing the "Boot" button during upload.
Unexpected behavior or crashes:
  • Review your code for errors or logical issues.
  • Ensure sufficient power supply, as unstable power can lead to erratic behavior.
  • Try uploading a known working sample program to isolate if the issue is hardware or software related.

8. User Tips

  • When developing with Arduino IDE, ensure you have the latest ESP32 board definitions installed for optimal compatibility and features.
  • For projects requiring significant data storage, leverage the TF card slot. Remember to initialize and manage the TF card within your code.
  • Experiment with the 12 available I/O pins to expand the module's functionality with various sensors and actuators.
  • Always double-check wiring, especially for power and battery connections, to prevent damage to the module.

9. Warranty and Support

For technical support, warranty claims, or further assistance, please contact the seller or manufacturer directly. Ensure you have your product model (JC3248W535C) and any relevant purchase information available when seeking support.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.