1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your new YeHua ABS Body Kit designed specifically for the Xpeng G6 models from 2023 to 2025. This kit includes a front shovel, side skirts, and a rear lip spoiler, crafted from durable ABS material to enhance your vehicle's aesthetic and aerodynamic profile.
Please read this manual thoroughly before beginning installation to ensure proper fitment and to maximize the lifespan of your product.
2. Setup and Installation
Professional installation is highly recommended for optimal results and to prevent damage to your vehicle or the body kit components. Ensure you have all necessary tools and a clean, well-lit workspace.
2.1. Pre-Installation Check
- Unpack all components and verify against the packing list that all parts are present and undamaged.
- Carefully test-fit each body kit component to its intended location on the vehicle before permanent attachment. This helps identify any potential fitment issues or necessary adjustments.
2.2. Surface Preparation
Thoroughly clean and dry the areas of your vehicle where the body kit components will be installed. Use an automotive-grade cleaner to remove any wax, grease, or dirt. A clean surface is crucial for proper adhesion.
2.3. Installation Steps
The installation typically involves a combination of drilling and adhesive application. Specific steps may vary slightly depending on the exact component (front shovel, side skirt, or rear lip).
- Front Bumper (Front Shovel): Position the front shovel accurately. Mark drilling points if necessary. Secure the component using screws or clips as provided, ensuring a snug fit.
- Side Skirts: Clean the side rocker panel area. Apply strong automotive-grade double-sided adhesive tape along the top edge of the side skirt. Carefully align and press the side skirt onto the vehicle. Additional screws may be used at the ends or underside for extra security.
- Rear Bumper (Rear Lip Spoiler): Align the rear lip spoiler with the lower section of the rear bumper. Mark and drill pilot holes if required. Attach the spoiler using the provided hardware, ensuring it is flush and securely fastened.
Refer to the following video for a visual guide on the installation process:
Video: Installation overview of the Xpeng G6 body kit components.
2.4. Component Visuals
3. Operation and Driving Considerations
Once installed, your Xpeng G6 body kit requires no special operational procedures. However, be mindful of the following driving considerations:
- Ground Clearance: Body kits can slightly reduce your vehicle's ground clearance. Exercise caution over speed bumps, steep driveways, and uneven terrain to avoid scraping or damaging the components.
- Aerodynamics: While designed to enhance aerodynamics, extreme speeds or strong crosswinds might have a subtle effect on vehicle stability. Drive responsibly and be aware of your vehicle's handling characteristics.
4. Maintenance
Proper maintenance will help preserve the appearance and integrity of your ABS body kit.
- Cleaning: Wash the body kit components regularly with mild automotive soap and water. Avoid abrasive cleaners or harsh chemicals that could damage the ABS material or its finish.
- Protection: Consider applying a UV protectant specifically designed for plastics to prevent fading and cracking over time, especially if the vehicle is frequently exposed to direct sunlight.
- Inspection: Periodically inspect all installed components for any signs of damage, loose fasteners, or compromised adhesive. Address any issues promptly to prevent further damage or detachment.
5. Troubleshooting
While the body kit is designed for precise fitment, minor issues can sometimes occur.
- Poor Fitment: If a component does not fit perfectly, re-check its alignment and ensure all mounting points are correctly positioned. Slight adjustments may be possible, but avoid forcing parts into place. If significant gaps or misalignments persist, consult with a professional installer.
- Loose Components: If any part of the body kit feels loose after installation, immediately re-secure it. Tighten screws, replace old adhesive tape with new, strong automotive-grade tape, or add additional fasteners as needed.
- Scratches/Minor Damage: Small scratches on the ABS material can often be buffed out with plastic polish. For deeper scratches or cracks, professional repair or replacement of the component may be necessary.
6. Specifications
| Feature | Detail |
|---|---|
| Brand | YeHua |
| Material | High-Quality ABS Plastic |
| Compatibility | Xpeng G6 (2023-2025 models) |
| Origin | Mainland China |
| Package Length | 167 cm |
| Package Width | 60 cm |
| Package Height | 35 cm |
| Package Weight | 1.2 kg |
| Color Options | Black Front bumper, Black Rear surround, Black Side skirts, Black three piece, Silver Black Front, Silver Black Rear, Silver Side skirts, Silver three piece |
7. User Tips
- Professional Installation: For the best fit and finish, especially with painted components, consider having the body kit installed by a professional automotive body shop.
- Adhesive Curing: If using adhesive tape, allow sufficient curing time (typically 24-48 hours) before washing the vehicle or driving at high speeds.
- Regular Checks: Periodically check all mounting points and fasteners to ensure they remain tight and secure, especially after driving on rough roads or through car washes.
8. Warranty and Support
For any questions regarding installation, product defects, or general inquiries, please contact the seller directly through the platform where the purchase was made. Keep your order details handy for faster assistance.
