Kunray 500W 25A Brushless Controller with LCD Display

Contents

Kunray 500W 25A Electric Bike Brushless Controller and LCD Display User Manual

Model: 500W 25A Brushless Controller with various LCD Display options

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your Kunray 500W 25A Electric Bike Brushless Controller and compatible LCD display. Please read this manual thoroughly before installation and use to ensure proper function and safety.

Kunray 500W 25A Electric Bike Brushless Controller and various LCD displays

Image: Overview of the Kunray 500W 25A Brushless Controller and several compatible LCD display models.

2. Safety Information

Always observe the following safety precautions:

  • Ensure all connections are secure and correctly wired before applying power.
  • Do not attempt to open or modify the controller or display units.
  • Keep the controller and display away from water and extreme temperatures unless specified as waterproof.
  • Always wear appropriate safety gear when operating an electric bike or scooter.
  • Verify that the motor voltage matches the battery voltage before connecting.

3. Product Overview

The Kunray 500W 25A Brushless Controller is designed for electric bikes and scooters, providing efficient power management for your motor. It is compatible with various LCD displays that offer different functionalities and user interfaces.

Controller

Kunray 500W 25A Brushless Controller

Image: The Kunray 500W 25A Brushless Controller unit.

Compatible LCD Displays

This controller is compatible with a range of LCD displays, each offering unique features. Common display models include S830U, S966, EN06, LED-G20, S800, M5, M9, UKC1, S100, S866, UKS6, S869, S900, GZ3, 124DX, G51, S5, S887, GD02, and S966-NFC. Ensure your chosen display uses the UART 2 Protocol for optimal compatibility.

4. Specifications

4.1 Controller Specifications

Parameter Value
Rated Power 500W
Rated Voltage 24V/36V/48V
Cutoff Voltage 19/29/39V ±0.5V
Current Output 25A ±1A
Dimensions (L*W*H) 125mm * 50mm * 30mm
Weight 350g
Mosfets 9 mosfets
Brake Input Low-level
Controller dimensions

Image: Dimensions of the 500W 25A controller (125mm length, 50mm width, 30mm height).

Controller product parameters

Image: Detailed product parameters for the 500W 25A controller.

4.2 Display Specifications (Examples)

Note: Specifications may vary slightly between different display models. Always refer to the specific display's documentation for precise details.

S830U Display

  • Product Shell: ABS
  • Gear Mode: 1-5
  • Voltage Rating: 24V/36V/48V
  • Waterproof Rating: IP65
  • Net Weight: 210g
  • Dimensions: 90mm (H) x 54mm (W)
  • Handlebar Clamp: 22mm
  • Features: USB Charging Port, UART 2 Protocol compatible.
S830 display specifications and wiring

Image: S830 display specifications including dimensions, voltage rating, and basic wiring (Red: battery positive, Black: negative, Blue: lock wire, Yellow: signal transmission, Green: signal reception).

S830U display with USB charging port

Image: S830U display highlighting the convenient USB charging port for mobile devices. Compatible with UART 2 protocol controllers.

EN06 Display

  • Operating Temperature: -20~60°C
  • Dimensions: 60mm * 46mm * 22.2mm
  • SM Length: 167cm / 65.74in
  • Weight: 87g
  • Wire Specification: SM plug, 5pin
  • Voltage: 24V-48V
  • Color: Black
  • Features: USB Charging Port, UART 2 Protocol compatible.
EN06 display specifications

Image: EN06 display specifications including dimensions, operating temperature, and wiring details.

EN06 display with USB charging port

Image: EN06 display showing its USB charging port. Note: This display uses UART 2 Protocol and is only compatible with UART 2 protocol controllers.

LED-G20 Display

  • IP65 Rated (Not Submersible)
  • Operating Temperature: -20~70°C
  • Dimensions: 48mm * 50mm * 22.2mm
  • SM Length: 164.5cm / 64.8in
  • Weight: 98.8g
  • Wire Specification: SM plug, 5pin+2pin
  • Voltage: 36V/48V
  • Color: Black
  • Features: Battery Level Indicator, Power Assist Level, On/Off Switch.
LED G20 display with controls

Image: LED G20 display showing battery level indicator, power assist level, and on/off switch.

LED G20 display specifications

Image: LED G20 display specifications including dimensions, operating temperature, and wiring details.

LCD M9 Display

  • Operating Temperature: -20~70°C
  • Dimensions: 111mm * 63mm * 22.2mm
  • SM Length: 163.5cm / 64.37in
  • Weight: 268g
  • Wire Specification: SM plug, 5pin+2pin
  • Voltage: 24V-72V
  • Color: Black
  • IP65 Rated (Not Submersible).
LCD M9 display specifications

Image: LCD M9 display specifications including dimensions, operating temperature, and wiring details.

LCD UKC1 Display

  • Voltage: 24-72V
  • Weight: 243g
  • Plug: 5 PIN
  • Features: USB charging port (5V 500MA).
LCD UKC1 display with USB charging port

Image: LCD UKC1 display showing its intelligent features and USB charging port.

LCD S866 Display

  • Type: LCD S866 Display
  • Plug: 5Pin Female SM Plug
  • Material: Plastic
  • Weight: 200g
  • Voltage: 24V, 36V, 48V
  • Holder Diameter: φ22mm
  • SM Length: 1700mm
  • Color: Black
  • Features: Monochrome and Color display options.
LCD S866 display monochrome and color versions

Image: LCD S866 display showing both monochrome and color versions with key specifications.

5. Installation and Setup

Follow these steps to install your brushless controller and LCD display:

5.1 Wiring Diagram

Refer to the diagram below for correct wiring connections. Ensure all connectors are firmly seated and match the corresponding ports.

Controller wiring diagram

Image: Detailed wiring diagram for the 500W brushless DC motor controller. Connections include Battery+-, Self Study, PAS Sensor, Headlight Power (Black: GND, Yellow: Power+), Throttle, Brake, Hall, Display, and Motor Phase. The battery connection uses an XT60 connector.

  • Battery+-: Connect your 24V/36V/48V battery using the XT60 connector.
  • Self Study: Used for initial motor pairing.
  • PAS Sensor: Connect the Pedal Assist System sensor.
  • Headlight Power: Connect your headlight (Black wire for Ground, Yellow wire for Power+).
  • Throttle: Connect the throttle unit.
  • Brake: Connect the brake levers.
  • Hall: Connect the motor's Hall sensor wires.
  • Display: Connect your compatible LCD display.
  • Motor Phase: Connect the motor phase wires.

5.2 Display Mounting

Mount the LCD display securely on your handlebar. Most displays are designed for a 22mm handlebar diameter. Ensure the display is positioned for easy viewing and access to buttons.

6. Operating Instructions

Operating procedures vary slightly depending on your specific LCD display model. Below are general instructions and examples for common display types.

6.1 General Display Functions

Most LCD displays provide the following information and controls:

  • Battery Display: Shows current battery charge level.
  • Speed Display: Current riding speed (km/h or mph).
  • Assist State & Light: Indicates pedal assist level and headlight status.
  • Multifunctional Display: May show trip distance, total mileage, time, etc.
  • Power Assist Status (PAS): Shows the current level of motor assistance.
  • Vehicle Mode Display: Indicates riding mode (e.g., STD, ECO, SPORT).

6.2 Button Operation (Example: S966 Display)

S966 display key interpretation

Image: S966 display showing key interpretation for parameter setting, function selection, and mode changes.

  • '+' Button: Long press for 3 seconds to turn on the light. Short press to change PAS gear.
  • 'M' Button: Long press for 3 seconds to turn on/off the display. Short press to cycle through function modes.
  • '-' Button: Long press for 3 seconds for push forward assist. Short press to change PAS gear.

6.3 NFC Function (Example: S966-NFC Display)

Some advanced displays like the S966-NFC offer keyless start and lock functions.

S966-NFC display open ways

Image: S966-NFC display illustrating three ways to unlock: NFC card, password, and mobile phone NFC.

  • NFC Card: Turn on power, then tap the screen twice with the NFC card to activate.
  • Password: After turning on power, briefly press the up or down key and enter the 2023 password to open.
  • Mobile Phone: After copying the card using NFC on your phone, the display panel can be opened via your phone.

7. Maintenance

  • Regularly check all wiring connections for tightness and signs of wear.
  • Keep the controller and display clean and free from dust and debris. Use a soft, dry cloth for cleaning.
  • Avoid exposing the units to direct sunlight for prolonged periods or extreme weather conditions.
  • If the display has a waterproof rating (e.g., IP65), it can withstand splashes but is generally not submersible.

8. Troubleshooting

If you encounter issues, refer to the following common problems and solutions:

Problem Possible Cause Solution
Display not turning on Loose connection, low battery, power switch off. Check all wiring, charge battery, ensure controller is powered on.
Motor not responding Incorrect wiring, faulty throttle/PAS sensor, motor/controller issue. Verify wiring against diagram, check throttle/PAS sensor functionality.
Inaccurate speed/mileage Incorrect wheel diameter setting in display. Access display settings to adjust wheel diameter.
Display shows 'ERROR' System fault, sensor error. Consult the specific display manual for error codes or contact support.

9. User Tips

  • Compatibility Check: Always ensure your display uses the UART 2 Protocol if your controller is also UART 2 compatible. For optimal performance, it is recommended to purchase the display and controller together.
  • Battery Voltage: If you are using an existing battery, confirm that its voltage (e.g., 36V or 48V) matches the rated voltage of the motor and controller.
  • PDF Manual: For more detailed instructions and specific display model information, refer to the official user manual PDF available at User manual (PDF).

10. Warranty and Support

The motor has a one-year warranty period. Accessories have a three-month warranty for quality problems, with free replacement. If the product is damaged or parts are lost in transit, the seller will take full responsibility.

For any questions or support, please contact Kunray customer service. They will assist you with inquiries and problem resolution.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.