JIKONG JK-B2A8S30PHC

Contents

JIKONG FACTORY BMS JK-B2A8S30PHC Battery Management System User Manual

Model: JK-B2A8S30PHC

1. Introduction

The JIKONG FACTORY BMS JK-B2A8S30PHC is an intelligent Battery Management System designed for large-capacity series lithium battery packs. It supports 4S to 8S configurations for Li-ion, LiFePO4, and LTO battery types. This BMS features a 300A continuous charge/discharge current and a 2A active balancing current, ensuring optimal battery performance and longevity.

Key functionalities include voltage acquisition, high-current active balancing, overcharge and over-discharge protection, overcurrent and over-temperature protection, coulomb meter, Bluetooth communication, and optional GPS remote capabilities. The system is managed via a mobile APP (Android and iOS) or PC software, allowing users to monitor battery status and adjust parameters.

JIKONG BMS JK-B2A8S30PHC with key features highlighted
Figure 1: JIKONG BMS JK-B2A8S30PHC with highlighted features.

2. Setup and Installation

2.1. Packing List

The standard package for the JK-B2A8S30PHC includes the following components:

  • BMS x 1
  • Sampling line x 1 (70cm long)
  • NTC (Temperature Sensor) x 1 (40cm long)
  • Switch key x 1 (50cm long)
Packing list for JIKONG BMS showing BMS unit, sampling line, NTC, and switch key
Figure 2: Included components in the packing list.

2.2. Product Dimensions

The JK-B2A8S-30P series protection board has dimensions of 174.77mm × 127.26mm × 17.6mm. Please ensure adequate space for installation and heat dissipation.

Dimensions of JIKONG BMS JK-B2A8S30P
Figure 3: Dimensions of the JK-B2A8S30P BMS.

2.3. Wiring and Connections

Before installation, gently handle the packaging and the protection board. Inspect for any impact marks or damage. The JK-B2A8S-30P series is suitable for 3-8 series lithium battery packs. The wiring method varies depending on the number of cells in your battery pack. Ensure all balance cables are properly connected and the P- and B- lines are correctly wired before powering on.

General Wiring Steps:

  1. Connect all balance cables to the BMS.
  2. Insert the main power cables (B- and P-) into the BMS.
  3. Connect the B-line to the battery negative terminal and the P-line to the battery positive terminal.
Wiring diagram for a 4-string cell battery with JIKONG BMS
Figure 4: Example wiring diagram for a 4-string cell battery.
Wiring diagram for an 8-string cell battery with JIKONG BMS, showing connections for controller, charger, and temperature probe
Figure 5: Example wiring diagram for an 8-string cell battery, including connections for controller, charger, and temperature probe.

2.4. Interface Definitions

The BMS features various interfaces for communication and control:

Diagram showing rich interfaces of JIKONG BMS including CAN, RS485, BT, NTC, Soft Switch, SOC Indicator, Key Switch, Active Equalizer
Figure 6: Rich interface options on the JIKONG BMS.

P1 (XH-10AW-2.54) - Balance and Acquisition Interface:

PinNameDescription
1B-Total negative battery
2-9B1-B8Positive terminals for battery strings 1-8
10B+Protection board power supply, connected to the battery positive

P2 (A1254WF-7A) - Heating Interface:

PinNameDescription
1-5HT-Heater element negative electrode
6CD+Charge indication input positive terminal
7CD-Charge indication input negative terminal

P3 (A1254WF-6A) - Display Interface:

PinNameDescription
1VCCDisplay power output
2ADisplay RS485 signal positive
3BDisplay RS485 signal negative
4GNDPower negative
5K+Activate signal positive
6K-Activate signal negative electrode

P4 (A1254WF-4A) - Communication Interface:

PinNameDescription
1485 BRS485 signal negative terminal
2485 ARS485 signal positive terminal
3CAN HCAN signal positive terminal
4CAN LCAN signal negative terminal

P5 (1.25T-4PWT) - GPS Interface:

PinNameDescription
1VGPSPower output, voltage close to B+
2TXUART TX, 3.3V
3RXUART RX, 3.3V
4GNDPower/signal ground

P6 (HY2.0-4P) - Temperature Interface 1:

PinNameDescription
1T1AFirst temperature sensor pin A
2T1BFirst temperature sensor pin B
3T2ASecond temperature sensor pin A
4T2BSecond temperature sensor pin B

P7 (HY2.0-4P) - Temperature Interface 2 (Optional 4 external):

PinNameDescription
1T3AThird temperature sensor pin A
2T3BThird temperature sensor pin B
3T4AFourth temperature sensor pin A
4T4BFourth temperature sensor pin B

P8 (A1254WF-3A) - Parallel Interface:

PinNameDescription
1GNDSignal ground
2P-ENParallel module enable signal (low level to enable)
3P-statusParallel module status signal

P9 (A1254WF-2A) - Buzzer Interface:

PinNameDescription
1VCCBuzzer power supply positive
2GNDBuzzer power negative

D1 - Bluetooth Connection Indicator: When Bluetooth is connected, the indicator is steady on. When disconnected, it blinks.

P- (Main Discharge/Charge Negative): Connects to external load or negative terminal of charger.

B- (Main Battery Negative): Connects to the negative battery terminal.

2.5. Device Activation

Before powering on the protection board, double-check all balance cable connections and ensure the P- and B- lines are correctly connected. Verify that the protection board is securely fixed to the battery cells. Incorrect connections can lead to abnormal operation or damage.

The protection board does not have a power-on control switch. It is designed for charging activation: the charger voltage must be 2V higher than the battery voltage. After battery assembly, connect the charger to activate the protection board.

Alternatively, the BMS supports key activation and display activation. If you have an optional display screen and button, simply connect the cable to the display interface and press the button to activate the device.

3. Operating Instructions

3.1. APP Installation and Parameter Setting

The JIKONG BMS can be managed via a mobile APP (Android and iOS) or PC software. To install the mobile APP, scan the QR code provided in the manual. Android devices require version 7 or higher.

Screenshot of JIKONG BMS APP interface on a computer screen
Figure 7: Intelligent interaction and easy operation via PC software.
Screenshot of JIKONG BMS mobile APP interface showing voltage, current, temperature, SOC, alarm, and cycles
Figure 8: Multi-screen display and data connection via mobile APP.

Before using the balancing function, set the basic battery parameters in the APP, including battery type, number of cells, battery capacity, balance trigger voltage difference, and voltage/current calibration. Default parameters are detailed in Section 5.2.

The APP allows you to view battery status, modify working parameters, and control charge/discharge switches. For specific parameter settings, refer to the 'Instructions for Setting Protection Board Parameters' document.

3.2. Active Equalization

The BMS uses energy transfer active balancing technology. Energy is transferred from higher-voltage cells to lower-voltage cells to achieve voltage balance with minimal energy loss. The default balance current is 2A. You can adjust the balance current based on your battery capacity, but it is recommended not to exceed 0.2C of the battery capacity.

Active balancing automatically activates when the voltage difference between any two battery strings exceeds the set value and turns off when the difference falls within the set range. If balancing is not required, you can disable it in the BMS control page of the APP.

Diagram illustrating active balancing (lossless balancing) in a battery pack
Figure 9: Active Balancing (Lossless Balancing) principle.

3.3. Protection Functions

The BMS provides comprehensive protection features:

  • Overcharge Protection and Recovery: Standard feature. Users can set single overcharge protection voltage and recovery voltage via the APP. The BMS will stop charging if any cell exceeds the set voltage and resume when all cells are below the recovery voltage.
  • Discharge Undervoltage Protection and Recovery: Standard feature. Users can set undervoltage protection voltage, recovery voltage, and automatic shutdown voltage. The BMS will stop discharging if any cell falls below the set voltage and resume when all cells are above the recovery voltage.
  • Charge Overcurrent Protection and Recovery: Standard feature. Users can set continuous charging current, overcurrent delay, and release time. The BMS will stop charging if the current exceeds the set value for the specified delay and resume after the release time.
  • Discharge Overcurrent Protection and Recovery: Standard feature. Users can set continuous discharge current, overcurrent delay, and release time. The BMS will stop discharging if the current exceeds the set value for the specified delay and resume after the release time. (Note: Maximum continuous discharge current should not exceed 300A).
  • Over-temperature Protection and Recovery: Standard feature for both charging and discharging. Users can set protection and recovery temperatures via the APP. The BMS will stop operation if temperatures exceed limits and resume when they fall within safe ranges.
  • Low-temperature Protection and Recovery: Standard feature for charging. Users can set protection and recovery temperatures via the APP. The BMS will stop charging if temperatures fall below limits and resume when they rise above recovery temperatures. Heating function is recommended for extremely cold areas.
  • Short-circuit Protection and Recovery: Standard feature. The trigger current is not user-settable, but delay (µs) and recovery time (S) can be adjusted via the APP. If a short circuit occurs, the BMS will stop operation and resume after the recovery time. If charging triggers a short circuit due to high peak current, increase the short circuit protection delay.

3.4. Heating Function (Optional)

The BMS supports an optional heating function to warm the battery in low-temperature conditions, preventing reduced battery activity. The designed heating current is 4A. Users can select this function and match appropriate heating equipment based on their needs. It is recommended to install a temperature control switch (45°C to 65°C normally closed type) in series with the heating circuit as a secondary protection.

3.5. Battery Parallel Function (Optional)

The BMS supports an optional battery parallel function for energy storage applications. This requires a parallel module and enabling the charging current limiting function in the APP.3.6. Discharge Precharge Function (Optional)

The BMS offers an optional discharge precharge function with a default time of 5 seconds. Users can enable or disable this function as needed. Setting the precharge time to 0 disables the function.

3.7. Emergency Switch

The BMS includes a standard emergency switch function. If issues like over-temperature, over-discharge, overcharge, or cell drop occur during normal use, activating the emergency switch in the APP will enable charge and discharge for 30 minutes. This provides an emergency use period. Even if a single cell reaches automatic shutdown voltage during this time, the protection board will continue to operate until the 30-minute cycle ends, preventing critical failures.

3.8. Intelligent Sleep

The BMS features an intelligent sleep function to reduce its own energy consumption when in standby (charging/discharging current less than 1A for 26 consecutive hours). Users can enable or disable this function via the APP. To reactivate the BMS from sleep, press the switch button or connect a charger.

3.9. Communication Function (Optional)

The BMS supports optional CAN/RS485 communication. Users can select CAN or RS485 for multiplexed ports in the APP. When using communication, set the address and protocol according to your requirements. Refer to the Jikong Protection Board communication protocol document for details.

Screenshot of JIKONG BMS APP showing CAN protocol selection for various inverter brands
Figure 10: Protocol docking and convenient setup via mobile APP for various inverter communication protocols.

4. Maintenance

To ensure the longevity and optimal performance of your JIKONG BMS, consider the following maintenance guidelines:

  • Regular Inspection: Periodically check all wiring connections for tightness and signs of wear or corrosion.
  • Cleanliness: Keep the BMS unit clean and free from dust and debris. Use a soft, dry cloth for cleaning.
  • Temperature Management: Ensure the BMS operates within its specified temperature range (-30°C to 70°C). Adequate ventilation is crucial, especially for high-current applications.
  • Firmware Updates: Check the official JIKONG website or APP for any available firmware updates to ensure your BMS has the latest features and bug fixes.
  • Avoid Physical Damage: Protect the BMS from physical shocks, vibrations, and moisture. The aluminum alloy shell provides good protection, but extreme conditions should be avoided.

5. Troubleshooting

If you encounter issues with your JIKONG BMS, consider the following general troubleshooting steps:

  • No Power/Activation Issues: Ensure all wiring is correct and secure. If using charging activation, verify the charger voltage is at least 2V higher than the battery voltage. If using a button, ensure it's properly connected and pressed.
  • Balancing Problems: Check the balance trigger voltage difference setting in the APP. Ensure the balance current is appropriate for your battery capacity.
  • Protection Triggered: If a protection (overcharge, over-discharge, overcurrent, over-temperature, low-temperature, short-circuit) is triggered, check the corresponding parameters in the APP. Review the battery status and environmental conditions that might have caused the trigger.
  • Communication Issues: Verify Bluetooth connection. For RS485/CAN, ensure correct wiring and protocol settings in the APP.
  • Abnormal Readings: If voltage or current readings appear incorrect, check the calibration settings in the APP.

For detailed troubleshooting and parameter adjustments, refer to the 'Instructions for Setting Protection Board Parameters' within the JIKONG APP or the comprehensive PDF manual.

6. Specifications

6.1. Basic Parameters

ParameterValueUnit
Supply Voltage10-36V
Operating Power Consumption<900mW
Operating Temperature-30 to 70°C
Max Number of Collection Strings8Strings
Max Balancing Current2A
Max Charging Current300A
Max Discharge Current300A
Max Instantaneous Current600A
Max Internal Loop Resistance0.3mΩ
Protective Plate Size174.77*127.26*17.6mm
Finished Weight421g

6.2. Default Parameters (for JK-B2A8S30PHC)

ParameterLi-Ion (Default)LiFePO4 (Default)LTO (Default)Unit
Balancing Initial Voltage332V
Max Balancing Current222A
Unit Overcharge Voltage4.23.62.7V
Single Overcharge Protection Recovery4.183.552.65V
Monomer Undervoltage Protection2.822.61.8V
Single Undervoltage Protection Recovery2.852.651.85V
Automatic Shutdown Voltage2.82.51.7V
SOC-0% Voltage2.92.61.85V
SOC-100% Voltage4.183.52.65V
Trigger Balancing Differential Pressure0.010.010.01V
Charging Overcurrent Protection Delay303030S
Charge Overcurrent Protection Release Time606060S
Discharge Overcurrent Protection Delay300300300S
Discharge Overcurrent Protection Release Time606060S
Short-circuit Protection Delay150015001500µS
Short-circuit Protection Release Time606060S
Charging Overtemperature Protection Temperature707070°C
Charge Overtemperature Restore Temperature606060°C
Discharge Overtemperature Protection Temperature707070°C
Discharge Overtemperature Recovery Temperature606060°C
Charging Low Temperature Protection Temperature-20-20-20°C
Charge Low Temperature Restore Temperature-10-10-10°C
MOS Overtemperature Protection Temperature100100100°C
MOS Overtemperature Recovery Temperature808080°C
Device Address000/
Discharge Precharge Time000S

Note: The data tolerance range is ±2mm for dimensions.

Table of JIKONG Product Specifications including battery strings, balance method, currents, and interfaces
Figure 11: JIKONG Product Specifications Table.

7. User Tips

  • APP Customization: Take advantage of the mobile APP to fine-tune protection parameters and balancing settings for your specific battery chemistry and usage patterns.
  • Cold Weather Operation: If operating in extremely cold environments, consider utilizing the optional heating function to maintain battery performance and prevent low-temperature charging issues.
  • Wiring Verification: Always double-check all wiring connections, especially balance leads and main power lines, before initial power-up to prevent damage to the BMS or battery pack.

8. Further Information and Support

For more detailed technical information, wiring diagrams, and advanced parameter settings, please refer to the official JIKONG Lithium Battery Active Balance Protection Board Maintenance Manual (PDF).

A PDF version of the user manual is available for download: JIKONG BMS User Manual (PDF).

For any further assistance or technical support, please contact JIKONG customer service.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.