LHY AUDIO GPSDO Taming Clock UCCM Module

Contents

LHY AUDIO GPSDO Taming Clock User Manual

GPS Timing 10MHz Frequency Reference UCCM Module OCXO Constant Temperature Crystal

1. Introduction

The LHY AUDIO GPSDO Taming Clock is a high-precision GPS Disciplined Oscillator (GPSDO) module designed to provide an extremely accurate 10MHz frequency reference. It integrates a Samsung UCCM (Universal Center Clock Module) with a built-in STP2878 OCXO (Oven Controlled Crystal Oscillator) and a uBlox LEA-6T GPS receiver module. This combination ensures fast locking, high sensitivity, strong frequency stability, and low phase noise, making it ideal for demanding applications such as HiFi audio systems and laboratory frequency references.

LHY AUDIO GPSDO Taming Clock front view
Figure 1: LHY AUDIO GPSDO Taming Clock (UCCM GPS Disciplined Oscillator)
LHY AUDIO GPSDO Taming Clock with included accessories
Figure 2: GPSDO Taming Clock with power adapter and GPS antenna.

2. Key Features and Performance

The UCCM module, originally designed for high-end communication equipment, provides exceptional performance:

  • Fast Locking: Quickly acquires and locks onto GPS signals.
  • High Sensitivity: Ensures reliable GPS signal reception.
  • Strong Frequency Stability: Maintains precise frequency output.
  • Low Phase Noise: Better than -100dBc @ 1Hz offset, crucial for high-fidelity audio and precise measurements.
  • High Accuracy: 24-hour average accuracy after GPS lock is 1x10-12, equivalent to 10.000000 00001MHz (0.001ppb).
  • Holdover Capability: Maintains an accuracy of 1x10-10 even when GPS is not connected, ensuring short-term precision stability for hours.
  • Anti-Interference & Fault-Tolerance: Maintains high precision even with short-term GPS signal interruption, adopting filtering algorithms to optimize signals under multipath effects or electromagnetic interference.
  • Cost-Benefit Balance: Offers performance comparable to or exceeding ordinary crystal oscillators at a significantly lower cost than pure atomic clocks.
  • Dual Output Channels: Provides two independent 10MHz outputs (Square Wave and Sine Wave).
Key features of the GPSDO Taming Clock including accuracy, stability, and output channels
Figure 3: Overview of key performance characteristics.

3. Specifications

ParameterValue
Monitoring SoftwareVarious RS232 terminal software, open-source LadyHeather
GPS AntennaSMA connector, DC5V active antenna
Phase Noise<-100dBc @ 1Hz offset (typical)
Allan Variance<1e-12 @ 1S
Power SupplyDC12.0V 1.5A
Product Weight0.6Kg
External Dimensions (W x H x D)115 mm x 65 mm x 155 mm
Clock Output (Square Wave)1.4Vpp @ 50 ohms; 3.3Vpp @ 1M ohms
Clock Output (Sine Wave)1.4Vpp / 7dBm @ 50 ohms
Communication InterfaceDB9, RS232, 57600/8/N/1
Dimensions of the GPSDO Taming Clock: 115mm width, 65mm height, 155mm depth
Figure 4: Product Dimensions.
Phase noise test chart for the GPSDO Taming Clock
Figure 5: Phase Noise Test Chart.
Allan variance test chart for the GPSDO Taming Clock
Figure 6: Allan Variance Test Chart.

4. Setup Instructions

Before connecting the GPSDO Taming Clock, ensure all components are present and undamaged.

4.1. Package Contents

  • GPSDO Timing Clock Host x1
  • DC12.0V 1.5A Power Adapter x1
  • Simple GPS Active Antenna, 3m Length x1

4.2. Connecting the Device

  1. Connect GPS Antenna: Connect the provided GPS active antenna to the "GPS ANT" SMA connector on the back panel. Ensure the antenna is placed in a location with a clear view of the sky for optimal signal reception.
  2. Connect Power: Plug the DC12.0V 1.5A power adapter into the "DC 12V" charging port (5.5x2.1mm) on the back panel, then connect the adapter to a suitable power outlet.
  3. Connect Output: Connect your audio device or frequency reference equipment to the desired 10MHz output ports:
    • "10MHz ~" for Sine wave output.
    • "10MHz ⊓" for Square wave output.
  4. (Optional) Connect RS232: For monitoring and configuration, connect a DB9 RS232 serial cable from the "RS232" port on the back panel to your PC.
Front and back panel diagram of the GPSDO Taming Clock with labeled ports and indicators
Figure 7: Front and Back Panel Layout with Port Descriptions.

5. Operation

Once powered on, the GPSDO Taming Clock will begin its initialization and GPS signal acquisition process. Monitor the front panel indicators for status.

5.1. Status Indicators

The front panel features four LED indicators: ACT (Activity), ERR (Error), ANT (Antenna), and ALM (Alarm). Their states indicate the operational status of the device:

StatusACT LightERR LightANT LightALM Light10MHz Square Wave Output10MHz Sine Wave Output
Power-on (cold start)OFFONOFFONOutput AvailableNo output
Starting StatusONOFFOFFOFFOutput AvailableNo output
GPS Satellite SearchingSlow flashOFFOFFOFFOutput AvailableNo output
GPS Satellite LockedFlash.OFFOFFOFFOutput AvailableOutput Available
GPS Antenna Disconnected/UnpluggedFlash.OFFONONOutput AvailableOutput Available
Internal GPS Board FailureOFFONOFFONOutput AvailableNo output
Internal OCXO Crystal FaultSlow flashOFFOFFONOutput AvailableNo output
Table showing GPSDO status indicators and corresponding output states
Figure 8: Panel Light Color Status and Output.

6. Connection & Monitoring

The UCCM module supports RS232 serial connection to a PC. It can be monitored and configured via terminal software or dedicated GPS monitoring software like LadyHeather. Viewable information includes UTC time, satellite signal strength, PPS time quality, frequency quality, and more.

To connect:

  1. Connect the RS232 port on the GPSDO to your computer using a DB9 serial cable (or a USB-to-serial adapter if your computer lacks a serial port).
  2. Open your preferred terminal software (e.g., PuTTY, Tera Term) or LadyHeather.
  3. Configure the serial port settings: 57600 baud rate, 8 data bits, No parity, 1 stop bit (57600/8/N/1).
  4. Once connected, you can observe real-time GPS and oscillator status data.
Screenshot of RS232 monitoring software (LadyHeather) displaying GPSDO data
Figure 9: Example of RS232 Monitoring Software Interface.

7. Applications in Audio Systems

GPSDOs are increasingly important in high-precision time synchronization, especially in high-end audio systems to enhance digital audio performance. The engineering philosophy of "clock = sound quality" is redefined through ultra-precise timing, making GPSDOs a key component for audiophiles and professionals seeking "zero distortion."

7.1. Digital Audio Clock Synchronization

Digital audio devices (such as DACs, ADCs, and digital audio converters) rely on a master clock to control the sampling rate. Clock jitter causes signal distortion, manifesting as a blurred sound field and lost details. The GPSDO provides an ultra-low phase noise 10MHz reference clock, significantly reducing system-level jitter and improving sound quality transparency and dynamic range.

High-end Hi-End DACs (e.g., dCS, Esoteric) can be paired with GPSDO modules for mastering audio production or audiophile systems.

7.2. Multi-device Time Synchronization

In large recording studios or live performances, multiple devices (e.g., mixers, effect processors, recorders) must be strictly synchronized to avoid timing errors. The GPSDO serves as the global clock source, distributing clock signals via WordClock or AES11 standards, ensuring aligned sampling points across all devices.

7.3. Network Audio Transmission Protocol Support

For network audio protocols like AES67 and Dante, IEEE1588 (PTP) implementation is crucial for microsecond-level synchronization. The GPSDO acts as the time source for PTP master clocks, providing a unified time base for large audio networks.

7.4. Spatial Acoustic Treatment

Advanced applications like beamforming or multi-channel immersive audio systems (e.g., Dolby Atmos) rely on precise time differences to locate sound sources. A GPSDO can optimize synchronization accuracy between multi-channel amplifiers and enhance sound image positioning accuracy.

8. Troubleshooting

Refer to the "Status Indicators" table (Section 5.1, Figure 8) for common issues and their corresponding indicator states.

  • No Output / Incorrect Output:
    • Check power connection.
    • Verify indicator lights against the status table. If ERR or ALM lights are ON, consult the table for the specific fault.
    • Ensure correct output port (Sine vs. Square wave) is used for your equipment.
  • No GPS Lock / Slow Locking:
    • Ensure the GPS antenna is securely connected and has a clear, unobstructed view of the sky.
    • Check the ANT light. If it's ON, the antenna might be disconnected or faulty.
    • Allow sufficient time for initial satellite acquisition (cold start can take longer).
  • RS232 Communication Issues:
    • Verify the RS232 cable connection.
    • Confirm serial port settings (baud rate, data bits, parity, stop bits) in your terminal software match the device specifications (57600/8/N/1).
    • Ensure correct COM port is selected.

9. Maintenance

  • Cleaning: Use a soft, dry cloth to clean the exterior of the device. Do not use liquid cleaners or solvents.
  • Ventilation: Ensure the device has adequate ventilation. Do not block the heat sink fins.
  • Environment: Operate the device in a stable environment, away from extreme temperatures, humidity, and strong electromagnetic fields.
  • Firmware Updates: Check the manufacturer's website periodically for any available firmware updates for the UCCM module or the GPSDO unit.

10. User Tips

  • For optimal GPS signal reception, place the GPS antenna outdoors or near a window with a clear view of the sky.
  • When using for HiFi audio, ensure proper grounding of all connected equipment to minimize noise.
  • Consider using high-quality 50-ohm coaxial cables for 10MHz output connections to maintain signal integrity.
  • If experiencing issues, a power cycle (unplugging and replugging the power adapter) can often resolve minor glitches.

11. Warranty and Support

For warranty information, technical support, or service inquiries, please contact your retailer or the manufacturer directly. Keep your purchase receipt as proof of purchase.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.