Lishui LSW90B

Contents

Lishui Ebike Motor Controller LSW90B Instruction Manual

Model: LSW90B

1. Introduction

This manual provides essential information for the proper installation, operation, and maintenance of your Lishui LSW90B Ebike Motor Controller. This high-quality controller is designed for use with electric bikes, electric motorcycles, and electric tricycles, supporting various voltage configurations and featuring sine wave control for smooth motor operation. Please read this manual thoroughly before installation and use to ensure optimal performance and safety.

2. Setup and Installation

The LSW90B controller is designed for brushless motors and requires careful connection to your e-bike system. Ensure all connections are secure and correctly matched to avoid damage to the controller or other components.

2.1. General Connection Overview

The controller features multiple wire harnesses for various functions. While specific wiring diagrams may vary based on your e-bike model and accessories, the general connection types include:

  • Motor Phase Wires: Typically three thick wires (e.g., green, yellow, blue) connecting to the motor's phase windings.
  • Hall Sensor Wires: A set of thinner wires (usually five or six, including power, ground, and three signal wires) connecting to the motor's Hall sensors.
  • Battery Power Wires: Two thick wires (red for positive, black for negative) connecting to the battery.
  • Throttle Connection: Wires for the throttle input, typically three wires (power, signal, ground).
  • Brake Levers: Connections for brake cut-off sensors.
  • Display/Meter: Wires for connecting to an LCD or LED display unit.
  • PAS (Pedal Assist Sensor): Connection for the pedal assist sensor.
  • Other Accessories: May include connections for lights, horn, cruise control, etc.

Refer to the following images for a visual representation of the controller and its various wire connections:

Lishui LSW90B Ebike Controller with multiple colored wires and connectors

Figure 1: Lishui LSW90B Ebike Controller with various wire harnesses.

Close-up of a hand holding a connector from the Lishui LSW90B Ebike Controller

Figure 2: Detail of a connector on the LSW90B controller.

2.2. Important Note for Compatibility

Due to potential variations in controller specifications and firmware, it is crucial to ensure compatibility with your existing e-bike system. When replacing a controller, you may need to provide specific 'Part number' and 'Comments number' details to ensure you receive a compatible unit. Failure to do so may result in the product not functioning correctly with your setup.

Important note regarding part and comments numbers for controller compatibility

Figure 3: Manufacturer's note on providing part and comments numbers for correct specification matching.

3. Operating Instructions

Once the LSW90B controller is correctly installed and connected to your e-bike system, its operation is typically managed through the e-bike's display unit (LCD or LED) and throttle. The controller translates your input into motor commands.

  • Power On/Off: Usually controlled via a button on your e-bike's display unit or battery.
  • Throttle Control: The controller receives signals from the throttle to regulate motor speed and power output.
  • Pedal Assist: If a PAS is connected, the controller will provide motor assistance based on your pedaling input and the selected assist level on your display.
  • Display Interaction: Use your e-bike's display to select assist levels, view speed, battery status, and other parameters.

4. Maintenance

To ensure the longevity and reliable performance of your Lishui LSW90B controller, follow these general maintenance guidelines:

  • Keep Dry: Protect the controller from water and excessive moisture. While designed to be durable, prolonged exposure to water can cause damage.
  • Clean Regularly: Gently wipe the exterior of the controller with a dry or slightly damp cloth to remove dust and dirt. Do not use harsh chemicals or abrasive cleaners.
  • Inspect Connections: Periodically check all wire connections to ensure they are secure and free from corrosion or damage. Loose connections can lead to intermittent operation or component failure.
  • Avoid Physical Impact: Mount the controller in a location where it is protected from physical shocks and impacts.
  • Temperature Management: Ensure the controller has adequate ventilation to prevent overheating, especially during prolonged use or in hot weather.

5. Troubleshooting

If you encounter issues with your LSW90B controller, consider the following troubleshooting steps:

  • No Power:
    • Check battery charge level.
    • Verify battery connections to the controller are secure.
    • Inspect the main power switch (if applicable) and its wiring.
  • Motor Not Responding:
    • Ensure throttle and PAS connections are correct and undamaged.
    • Check motor phase wires and Hall sensor wires for proper connection.
    • Verify that the correct 'Part number' and 'Comments number' were used during purchase to ensure compatibility with your motor. An incompatible controller will not operate the motor.
  • Erratic Operation:
    • Inspect all wiring for loose connections or signs of damage.
    • Ensure no water or debris has entered the controller casing.

If problems persist after performing these checks, contact customer support for further assistance.

6. Specifications

Feature Specification
Model LSW90B
Application E-bike, Electric motorcycle, electric tricycle
Rated Voltage 24V, 36V, 48V, 60V, 72V (Specific unit label shows 36V)
Maximum Current 15A (Specific unit label)
Rated Current 10A, 15A, 20A, 25A (Specific unit label shows 7A)
Low Voltage Protection 31V (Specific unit label)
Control Type Sine wave
Material Stainless steel
Display Type Compatibility LCD, LED
Feature Durable
Package Length 20 cm
Package Width 9 cm
Package Height 7 cm
Package Weight 0.58 kg
Close-up of the Lishui LSW90B controller label showing detailed specifications

Figure 4: Controller label with detailed specifications.

7. User Tips

  • Verify Compatibility: Before purchasing or installing, always confirm the 'Part number' and 'Comments number' of your existing controller or motor to ensure the LSW90B controller is fully compatible with your e-bike system. This is critical for proper function.
  • Professional Installation: If you are unsure about wiring or electronic connections, it is highly recommended to seek professional assistance for installation to prevent damage to the controller or your e-bike.

8. Warranty and Support

For any technical support, inquiries, or assistance with your Lishui LSW90B Ebike Motor Controller, please contact the seller directly using the following information:

  • Whatsapp/Wechat: +86 19350856924
  • Email: zlinshow001@163.com

Please have your product details, including any part numbers or comments numbers, ready when contacting support to facilitate a quicker resolution.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.