ANDELI DB

Contents

ANDELI Auto Darkening Welding Helmet User Manual

Model: DB

Introduction

Thank you for choosing the ANDELI Auto Darkening Welding Helmet. This manual provides essential information for the safe and effective operation, maintenance, and troubleshooting of your welding helmet. Please read this manual thoroughly before use and keep it for future reference.

For a detailed PDF version of this manual, please refer to the official document: User Manual (PDF).

Package Contents

Upon unpacking, please ensure all items listed below are present and undamaged:

  • 1 x ANDELI Auto Darkening Welding Helmet
  • 1 x External Protective Lens
  • 1 x Internal Protective Lens
  • 2 x Replaceable Lithium Battery (Built-in)
  • 1 x Convenient Bag
ANDELI Welding Helmet and Package Contents
Image: Welding Helmet and included accessories: External Protective Lens, Internal Protective Lens, Replaceable Lithium Batteries, and a Convenient Bag.

Safety Information

WARNING: Read and understand all safety precautions before operating this equipment. Failure to do so may result in serious personal injury or loss of life.

General Safety

  • Always inspect the helmet and filter lens for proper fit and condition before welding.
  • Ensure the clear lens is clean and securely attached.
  • Always wear safety glasses or goggles under the welding helmet.
  • Wear appropriate protective clothing to shield skin from radiation, burns, and spatter.
  • Ensure optical radiation from other arcs does not enter from behind the helmet.
  • Auto-darkening filters protect against harmful UV/IR rays in both dark and light states.
UV/IR Protection DIN16
Image: The helmet provides UV/IR protection up to DIN16, effectively blocking harmful ultraviolet and infrared radiation.
Good Eye Protection blocking blue light
Image: Diagram illustrating how the helmet blocks harmful blue light, providing good eye protection.

Fumes and Gases

  • Avoid breathing welding fumes and gases. Keep your head out of the fume plume.
  • Use sufficient ventilation or exhaust at the arc to keep fumes away from your breathing zone.
  • Special ventilation may be required for certain electrodes (e.g., stainless steel, hard facing) or materials (e.g., lead, cadmium plated steel, galvanized steel) that produce highly toxic fumes.
  • Do not weld in areas with chlorinated hydrocarbon vapors (e.g., from degreasing/spraying operations) as they can react with arc heat to form toxic gases.
  • Shielding gases can displace air; ensure adequate ventilation in confined spaces.

Arc Rays and Electric Shock

  • Arc rays can injure eyes and burn skin. Use a shield with proper filter and cover plates conforming to ANSI Z87.1 standards.
  • Electric shock can kill. Do not touch "hot" electrical parts with bare skin or wet clothing. Wear dry, hole-free gloves.
  • Insulate yourself from work and ground using dry insulation.
  • Ensure work cable has a good electrical connection to the metal being welded, as close to the welding area as possible.
  • Maintain electrode holder, work clamp, and welding cable in good, safe condition. Replace damaged insulation.

Fire and Explosion Hazards

  • Remove all fire hazards from the welding area or cover them to prevent sparks from igniting a fire.
  • Have a fire extinguisher readily available.
  • Do not weld or cut tanks, drums, or containers that have held hazardous substances unless properly cleaned and vented.
  • Vent hollow castings or containers before heating, cutting, or welding to prevent explosions.
  • Wear oil-free protective garments to protect against sparks and spatter.

Compressed Gas Cylinders

  • Use only compressed gas cylinders with the correct shielding gas and properly operating regulators.
  • Keep cylinders upright and securely chained.
  • Locate cylinders away from heat, sparks, flame, and physical damage.
  • Never allow electrical parts to touch a cylinder.
  • Keep your head away from the cylinder valve outlet when opening the valve.
  • Valve protection caps should always be in place and hand tight when not in use.

Regulatory Statements

This device complies with FCC Part 15 rules and Innovation, Science, and Economic Development Canada license-exempt RSS standard(s). Operation is subject to the following conditions:

  1. This device may not cause harmful interference.
  2. This device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment. This equipment complies with radiation exposure limits for an uncontrolled environment and can be installed and operated at a distance equal to or less than 5mm between the radiator and your body.

CALIFORNIA PROPOSITION 65 WARNINGS:

  • Breathing diesel engine exhaust exposes you to chemicals known to the State of California to cause cancer and birth defects, or other reproductive harm. Always start and operate the engine in a well-ventilated area. If in an exposed area, vent the exhaust to the outside. Do not modify or tamper with the exhaust system. Do not idle the engine except as necessary. For more information goto www.P65warnings.ca.gov/diesel
  • This product, when used for welding or cutting, produces fumes or gases which contain chemicals known to the State of California to cause birth defects and, in some cases, cancer. (California Health & Safety Code § 25249.5 et seq.) For more information goto www.P65warnings.ca.gov

Specifications

FeatureSpecification
Brand NameANDELI
Model NumberDB
Optical Class1/1/1/2
LCD Viewing Area100 x 95 mm (3.94 x 3.74 in.)
Cartridge Size114 x 133 mm (4.50 x 5.25 in.)
UV/IR ProtectionUV/IR protection up to DIN16
Arc Sensors4
Variable Welding ShadesWELD Model: DIN9-13 (LightState: DIN4)
CUT Model: DIN5-9 (LightState: DIN4)
GRIND Model: LightState: DIN4
Shade ControlVariable, adjust by external knob
Sensitivity ControlVariable, adjust by external knob
Power SupplySolar cells with battery assist (2x CR2032 Lithium, built-in)
Low Battery WarningRed Light Indicator
Power On/OffFully automatic
Light to Dark Switching Time1/25,000 sec.
Dark to Light Switching Time0.3 sec. - 0.9 sec. (adjustable)
TIG RatingDC ≥ 5 amps; AC ≥ 5 amps
Operating Temperature-5°C to 55°C (23°F to 131°F)
Storage Temperature-20°C to 70°C (-4°F to 158°F)
Total Weight610g
MaterialPP (Helmet Material), Plastic
Is Smart DeviceNo
180 degree large viewing area of welding helmet
Image: The helmet features a 180° large viewing area with dimensions of 3.94" x 3.74" for enhanced visibility.
True Color Technology and ADF dimensions
Image: True Color Technology for better clarity. The Auto-Darkening Filter (ADF) measures 13.8 cm (5.43 inch) in height and 12 cm (4.72 inch) in width, with a solar panel on top.
Auto-darkening speed and arc sensors
Image: The helmet features 1/25000s auto-darkening speed and 4 premium arc sensors for rapid response.

Setup and Adjustment

Headgear Adjustment

Proper adjustment of the headgear is crucial for comfort and safety.

  • Head Size Adjustment: Turn the Ratchet Knob (located at the back of the helmet) right or left to adjust the headgear tightness for your desired head size.
  • Tilt Adjustment: Loosen the right headgear tension knob. Push the top end of the adjustment lever outward until the lever's Stop Tab clears the notches. Rotate the lever forward or back to achieve the desired tilt position. The Stop will automatically engage to lock the helmet in position.
  • Fore/Aft Adjustment: This adjusts the distance between your face and the lens. Slide and hold the spring-loaded caps upward while moving the headgear into one of the four slotted locations. Release the caps once the desired distance is achieved. Ensure both sides are equally positioned.
Comfortable headgear with 130 degree adjustment
Image: The comfortable headgear is sweatproof, adjustable up to 130 degrees, and designed to reduce pressure points.

Initial Check and Battery

  • Self-Test Button: Press the "Self-test button" (No. 6 on the helmet controls diagram, refer to PDF page 12) to check if the lens is working properly. The lens should darken and then return to the clear state. Do not use the helmet if it does not function as described.
  • Low Battery Indicator: A red light indicates low battery. The helmet uses two CR2032 lithium batteries. If the indicator lights up, replace the batteries promptly.
  • Battery Replacement: The batteries are located at the bottom corner of the ADF cartridge. Replace with CR2032 lithium type batteries. Ensure the Positive (+) side of the battery faces up (toward the inside of the helmet).

Operating Instructions

Helmet Controls Overview

The helmet features several external controls for easy adjustment during operation (refer to the diagram on PDF page 12 for visual reference):

  1. Sensitivity control knob
  2. Delay time control knob
  3. Grind-Cut-Weld mode switch
  4. Lithium battery (internal)
  5. Shade control knob
  6. Self-test button
  7. Low voltage indicator
  8. LCD (Auto-Darkening Filter)
  9. Arc sensor (4 sensors)
  10. Solar cell
  11. UV/IR filter

Mode Control (Grind-Cut-Weld Switch)

Three adjustable modes for welding helmet
Image: The helmet offers three adjustable modes: Grind (DIN4), Cut (DIN5-9), and Weld (DIN9-13).
  • Weld Mode (DIN9-13): For most welding applications (MIG, MAG, MMA, TIG). The lens automatically darkens upon sensing a welding arc. Adjust shade, sensitivity, and delay as needed.
  • Cut Mode (DIN5-9): For cutting applications. The lens darkens upon sensing a cutting arc. Adjust shade, sensitivity, and delay as needed.
  • Grind Mode (DIN4): For metal grinding applications. The lens is fixed at shade DIN4. No lens adjustments are possible in this mode.
Welding helmet with wide application modes
Image: The welding helmet is suitable for a wide range of applications including Cut, Grind, MMA, MIG, and TIG welding.

Variable Shade Control

Use the Shade control knob (No. 5) to adjust the lens shade in the darkened state. Refer to the table below for recommended shade settings based on your welding process and current (Amperes).

Welding ProcessArc Current (Amperes)
0.5-12.5-510-1520-3040-6080-100125-150175-200225-250275-300350-400450-500
SMAW91011121314
MIG (heavy)1011121314
MIG (light)101112131415
TIG, GTAW91011121314
MAG/CO2101112131415
SAW101112131415
PAC11121314
PAW89101112131415

Note: SMAW = Shielded Metal Arc Welding, MIG (heavy/light) = MIG on heavy/light metals, TIG/GTAW = Gas Tungsten Arc Welding, MAG/CO2, SAW = Shielded Semi-Automatic Arc Welding, PAC = Plasma Arc Cutting, PAW = Plasma Arc Welding.

Sensitivity Control

The Sensitivity control knob (No. 1) adjusts the lens's responsiveness to the welding arc. The default sensitivity is medium.

  • Minimum Sensitivity: Suitable for high amperage welding or welding in bright ambient light (e.g., near other welders).
  • Maximum Sensitivity: Suitable for low amperage welding, welding in low light conditions (e.g., pipe welding where the arc is partially obscured), or when the welding arc is stable (e.g., TIG welding).
  • Warning: If the LED is on or in a strong light environment, the ADF may mistakenly trigger. Reduce sensitivity to a position below 5 if this occurs.

Lens Delay Control

The Delay time control knob (No. 2) adjusts the time it takes for the lens to switch back to the clear state after welding. This is useful for preventing bright after-rays, especially in high amperage applications where the molten puddle remains bright momentarily. The delay can be adjusted from 0.3 seconds to 0.9 seconds.

Maintenance

Cleaning

  • Front Clear Cover Lens: If dirty, clean with soapy water and a soft cloth. If damaged, replace it. Carefully remove the fixing bolt from the left and right sides, replace the lens, and secure the bolt.
  • Auto-Darkening Cartridge: Clean with soapy water and a soft cloth.

Battery Replacement

When the low battery indicator lights up, replace the two CR2032 lithium batteries. Ensure the Positive (+) side faces up (towards the inside of the helmet).

Lens Replacement

  • Front Clear Cover Lens: If damaged, replace. Remove the fixing bolts on both sides, replace the lens, and re-secure the bolts.
  • Inside Clear Lens: Remove the inside lens cover by pulling the top center from its holding channels. Gently bow the new lens in the center and insert one end at a time into the channels.
  • Shade Cartridge: Remove the ADF holder assembly from the helmet shell. Flex the bottom end of the ADF holder to remove the old cartridge. Install the new ADF cartridge, ensuring it is correctly inserted, then reassemble the holder into the helmet shell.

Installing an Aftermarket Magnifying Lens

To install a magnifying lens, simply slide it into the short rail located on the sides of the ADF holder. The shade cartridge must be removed from the ADF holder to install the magnifying lens.

Troubleshooting

WARNING: If any problems cannot be corrected, stop using the helmet immediately and contact the dealer.

ProblemPossible CauseSolution
Difficult to see through filter.Front cover lens dirty.
Cartridge dirty.
Clean or replace front cover lens.
Clean the Auto-Darkening cartridge with soapy water and soft cloth.
Filter does not darken when arc is struck.Sensitivity set too low.
Front cover lens dirty.
Front cover lens damaged.
Sensors or solar panel blocked.
Grind Mode selected.
Switch on 5-9/9-13 stuck in middle.
Adjust sensitivity to required level.
Clean or replace front cover lens.
Check for cracked or pitted lens, replace if needed.
Ensure sensors/solar panel are not blocked; adjust position.
Ensure proper shade is selected.
Turn switch to correct position.
Filter remains dark after completing a weld.Sensitivity set too high.
Delay time set too high.
Low Battery.
Adjust sensitivity to required level.
Adjust delay time to required level.
Replace battery.
Filter does not darken when TEST button is pushed.Low battery.Replace battery.
LED will not turn on after pressing button.Plug-in jack from filter not completely inserted.Remove plug-in jack and re-insert it.

User Tips

  • Always perform a quick visual inspection of your helmet and lens before each use to ensure no damage or dirt could impair visibility or protection.
  • Adjust the headgear for a snug but comfortable fit to prevent the helmet from slipping during work and to minimize pressure points.
  • Experiment with sensitivity and delay settings in a safe environment to find what works best for your specific welding tasks and ambient lighting conditions.
  • Keep spare CR2032 batteries on hand to avoid interruptions during critical work.
  • Regularly clean the external and internal protective lenses to maintain optimal clarity and extend their lifespan.

Warranty and Support

For any questions, technical support, or warranty claims, please contact ANDELI customer service:

  • Official Website: www.andelitools.com
  • After-sales Email: support@andeligroup.com
  • After-sales Number (USA): +1 949 617 9002
  • After-sales Number (Hong Kong): +852 8480 7265
  • After-sales Address (USA): LIPO INC D-100, 12 Hughes Irvine, CA 92618 US
  • After-sales Address (Hong Kong): Workshop 60, 3/F, Block A, East Sun Industrial Centre, No. 16 Shing Yip Street, Kwun Tong, Hong Kong

Please have your product model (DB) and purchase information ready when contacting support.

© ANDELI. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.