1. Introduction
The PORTXVNSA NanoVNA-H4 Plus is an upgraded Vector Network Analyzer (VNA) designed for a wide range of RF and antenna analysis tasks. With an extended measurement range of 50KHz to 2.7GHz and an increased number of scanning points to 401, it offers enhanced precision and versatility. Its ergonomic design, 4-inch IPS LCD resistive touch screen, and built-in 5000mAh battery make it a portable and powerful tool for HAM radio enthusiasts and RF electronics hobbyists.
2. Key Features
- Wide Frequency Range: 50KHz to 2.7GHz for comprehensive analysis.
- High-Resolution Display: 4-inch IPS LCD with resistive touch screen, wide viewing angle, accurate color reproduction, and high contrast.
- Enhanced Scanning: Increased to 401 scanning points for detailed measurements.
- Ergonomic Design: Comfortable and practical for handheld use.
- Long Battery Life: Built-in 5000mAh large capacity battery for extended operation.
- PC Control: Compatible with Nano Saver software for advanced data analysis and saving Touchstone files.
- Versatile Measurements: Capable of scanning antenna systems and cables, SWR and impedance matching, measuring dual-band and triple-band duplexers, port isolation by frequency band, and measuring insertion loss of filters.
3. Package Contents
Ensure all items are present upon unboxing:
- 1x NanoVNA-H4 Plus Unit
- 1x USB Type-C Cable
- 2x SMA Male to Male RG316 RF Cables
- 1x SMA Calibration Kit (OPEN/SHORT/LOAD)
- 1x SMA Female to Female Connector
- 1x SMA Male to Female Right Angle Connector
- 1x Stylus
- 1x 32GB MicroSD Card

Image: NanoVNA-H4 Plus unit and its accessories, including cables, connectors, stylus, and SD card.
4. Setup
4.1 Initial Power On
- Ensure the device is charged using the provided USB Type-C cable. The device has a 5000mAh rechargeable battery.
- Press the power button located on the top of the device to turn it on.
4.2 Connecting to PC (Optional)
The NanoVNA-H4 Plus can be controlled via PC using the Nano Saver software. Connect the device to your computer using the USB Type-C cable. The Nano Saver software allows you to save Touchstone files, sweep frequency spans in segments, and display/analyze resulting data.

Image: NanoVNA-H4 Plus connected to a laptop via its Type-C port for PC control using Nano Saver software.
4.3 Connecting Antennas/Cables
Use the SMA connectors (CH0 and CH1) on the left side of the device to connect your antenna or cable under test. Utilize the provided SMA male to male RG316 RF cables and various connectors as needed for your specific measurement setup.
5. Operating Instructions
The NanoVNA-H4 Plus features a resistive touch screen and a rotary encoder for navigation and parameter adjustment.
5.1 Basic Navigation
- Touch Screen: Tap on menu options or input fields to select them.
- Rotary Encoder: Rotate to scroll through options or adjust values. Press to confirm selection.
Video: Demonstration of NanoVNA-H4 Plus user interface navigation, including menu selection, parameter adjustment, and touch screen functionality.
5.2 Calibration
Before performing accurate measurements, it is crucial to calibrate the VNA. Use the provided SMA calibration kit (OPEN, SHORT, LOAD) for precise calibration across your desired frequency range. Refer to the on-screen menu for calibration steps (typically found under 'CALIBRATE' or 'CONFIG' menu).
5.3 Performing Measurements
The device can perform various measurements, including:
- Antenna System and Cable Scanning: Connect the antenna or cable to CH0 or CH1 and select the appropriate measurement mode.
- SWR and Impedance Matching: Display Smith Chart and SWR graphs to analyze antenna performance.
- Duplexer Measurement: Measure dual-band and triple-band duplexers.
- Filter Analysis: Measure insertion loss of filters.

Image: Examples of measurements, including 2.4 GHz antenna, shortwave antenna, and cable length measurement.
5.4 Setting Parameters
Navigate through the menus to set parameters such as START/STOP frequency, number of sweep points (up to 401), and display format (e.g., Smith Chart, LogMag, SWR, Phase, Delay, Resistance, Reactance).
6. Maintenance
- Cleaning: Use a soft, dry cloth to clean the device. Avoid abrasive cleaners or solvents.
- Storage: Store the device in a cool, dry place away from direct sunlight and extreme temperatures.
- Battery Care: For optimal battery life, avoid fully discharging the battery frequently. Charge the device regularly, even if not in use for extended periods.
- Firmware Updates: Periodically check the manufacturer's website or community forums for firmware updates to ensure optimal performance and access to new features.
7. Troubleshooting
- Device not powering on: Ensure the battery is charged. Connect to a power source using the USB Type-C cable.
- Inaccurate measurements: Perform a full calibration with the provided calibration kit. Check all cable connections for tightness and proper contact.
- Touch screen unresponsive: Try restarting the device. If issues persist, perform a touch screen test (usually found in the 'CONFIG' or 'EXPERT SETTINGS' menu).
- PC software not connecting: Ensure the correct drivers are installed and the USB Type-C cable is securely connected. Refer to the Nano Saver software documentation for specific connection instructions.
8. Specifications
| Feature | Specification |
|---|---|
| Frequency Range | 50KHz-2.7GHz |
| Display | 4-inch IPS LCD (Resistive Touch Screen) |
| Scanning Points | 401 |
| Sweep Speed | 100 points/second |
| Battery | 5000mAh Rechargeable |
| Interface | USB Type-C |
| Control | Touch screen + Rotary encoder |
| PC Software | Nano Saver |
| Origin | Mainland China |
| Certification | CE |
9. User Tips
- Always perform a calibration for the specific frequency range you intend to measure to ensure the most accurate results.
- When measuring sensitive circuits, ensure proper shielding and grounding to minimize external interference.
- Utilize the PC software (Nano Saver) for more in-depth analysis and data logging, especially for complex projects or long-term monitoring.
- Keep the firmware updated to benefit from performance improvements and new features.
10. Support
For further assistance, technical support, or detailed documentation, please refer to the official product page or contact the manufacturer directly. Community forums dedicated to NanoVNA devices can also be a valuable resource for tips and troubleshooting.