ZIBOO FT-1000W, FT-2000W

Contents

ZIBOO Solar MPPT Meter User Manual

Models: FT-1000W, FT-2000W

Brand: ZIBOO

1. Introduction

The ZIBOO Solar MPPT Meter (models FT-1000W and FT-2000W) is a professional tool designed for testing solar photovoltaic panels. It provides accurate measurements of maximum power point (Pmax), maximum power point voltage (Vmp), maximum power point current (Imp), open circuit voltage (Voc), and short circuit current (Isc). This meter is essential for solar panel installation, maintenance, and troubleshooting, offering high precision, performance, and safety features.

This manual provides detailed instructions for the safe and effective use of your ZIBOO Solar MPPT Meter.

ZIBOO FT-2000W Solar MPPT Meter and accessories

Figure 1: ZIBOO FT-2000W Solar MPPT Meter and included accessories.

2. Safety Precautions

WARNING: Please read all safety instructions carefully before use to prevent electric shock, injury, or damage to the meter.

  • This product adheres to safety standards for solar energy industry in China and Europe.
  • Always operate the instrument strictly in accordance with the prescribed safety regulations.
  • Measure only within the specified safety range of the product to avoid damage.
  • Do not touch conductors with a voltage exceeding 30V during measurement. Exercise caution to avoid electric shock.
  • If the measurement exceeds the range, a high-voltage lightning symbol and a buzzer alarm will be displayed. Pay attention to measurement safety.
  • Do not use in flammable, explosive, or other special environments.
  • Replace batteries promptly when the low battery symbol is displayed to avoid measurement errors.
  • Before measurement, inspect test leads for damage or leaks. Do not use if damaged.
  • Correctly connect the standard MC4 connectors and verify positive and negative polarity of the test leads.
  • Pay close attention to all safety symbols and warnings on the device and in this manual.
Solar panel connection warning diagram

Figure 2: Correct and incorrect wiring for solar panel testing. Always connect in parallel, not series.

3. Package Contents

Please check the contents of your package upon receipt. The following items are typically included:

FT-1000W Model:

  • 1 x ZIBOO Solar MPPT Meter (FT-1000W)
  • 1 x Special Test Lead
  • 3 x AAA Batteries
  • 1 x User Manual & Gift Box
  • 1 x Strap
  • 2 x Special Interface Wrench Tools
FT-1000W Product List

Figure 3: FT-1000W included accessories.

FT-2000W Model:

  • 1 x ZIBOO Solar MPPT Meter (FT-2000W)
  • 1 x Alligator Clip Test Lead (exclusive to FT-2000W)
  • 1 x Special Test Lead
  • 3 x AAA Batteries
  • 1 x User Manual & Gift Box
  • 1 x Strap
  • 2 x Special Interface Wrench Tools
FT-2000W Product List

Figure 4: FT-2000W included accessories.

Standard MC head disassembly tool

Figure 5: Standard MC head disassembly tools for photovoltaic connector interfaces.

Standard MC4 test leads included

Figure 6: Standard MC4 test leads for convenient and reliable measurement. Alligator clip test lead is included only with FT-2000W.

4. Setup and Connection

Before operating the meter, ensure proper connection to the solar panel.

  1. Insert Batteries: Open the battery compartment on the back of the meter and insert 3 AAA 1.5V batteries, observing polarity. Securely close the compartment.
  2. Connect Test Leads:
    • Insert the red test lead into the positive (+) input port on the meter.
    • Insert the black test lead into the negative (-) input port on the meter.
    • Connect the other end of the red test lead to the positive terminal of the solar panel.
    • Connect the other end of the black test lead to the negative terminal of the solar panel.
  3. MC4 Connection: For standard MC4 connectors, ensure a secure and correct connection. The video below demonstrates the standard MC4 test line connection.
  4. Power On: Press and hold the power button (Power button icon) for 3 seconds to turn on the device.

Video 1: Demonstration of standard MC4 test line connection and basic operation.

5. Operating Instructions

The ZIBOO Solar MPPT Meter offers both automatic and manual measurement modes, along with data hold and backlight functions.

ZIBOO FT-2000W showing display and buttons with labels

Figure 7: Overview of the meter's display and control buttons.

5.1 Power On/Off

  • Power On: Press and hold the power button (Power button icon) for approximately 3 seconds.
  • Power Off: Press and hold the power button for approximately 2 seconds. The device will also auto power off after about 10 minutes of inactivity.

5.2 Automatic Measurement (AUTO Mode)

This mode provides continuous, cyclic measurements, refreshing data every few seconds.

  1. Ensure the meter is connected correctly to the solar panel.
  2. Press the AUTO button. The meter will automatically begin measuring and display updated data approximately every three seconds.
  3. To stop automatic measurement, press the AUTO button again or switch to Manual mode.

5.3 Manual Measurement (MANUAL Mode)

For single, on-demand measurements.

  1. Ensure the meter is connected correctly to the solar panel.
  2. Press the MANUAL button. The meter will wait for 3 seconds and then start the test, displaying the measurement results.
  3. To perform another manual measurement, press the MANUAL button again.

5.4 Data Hold

To freeze the current readings on the display:

  • During any measurement, press the HOLD button. The displayed data will remain unchanged.
  • Press the HOLD button again to release the data and resume live readings.

5.5 Backlight Control

To activate or deactivate the display backlight:

  • Press and hold the HOLD button for approximately 3 seconds to turn the backlight on or off.

6. Display Symbol Explanation

SymbolExplanation
PmaxMaximum power point (W), the power at which the maximum electricity generation occurs under strong light conditions.
VmpMaximum power point voltage (V).
ImpMaximum power point current (A).
VocOpen-circuit voltage (V), the voltage measured when the solar panel is not connected to a load.
IscShort-circuit current (A), the current measured when the positive and negative poles of the solar panel are short-circuited.
MANUALManual measurement mode indicator.
AUTOAutomatic loop measurement mode indicator.
HOLDData hold symbol, indicating data is frozen on screen.
Power iconPower on/off indicator.
OLOverload display.
Battery SymbolLow voltage symbol, prompting battery replacement.
Temperature SymbolIndicates excessive internal temperature (over 60°C), leading to test stoppage.

7. Technical Specifications

ParameterFT-1000WFT-2000WResolutionAccuracy
Maximum Power (Pmax)1000W2000W0.1W±(1.0%+5)
Maximum Voltage (Vmp)80V120V0.1V±(1.0%+5)
Maximum Current (Imp)35A35A0.1A±(1.0%+5)
Open Circuit Voltage (Voc)80V120V0.1V±(1.5%+5)
Short Circuit Current (Isc)35A35A0.1A±(1.5%+5)

General Specifications:

  • Input Protection: Anti-mistake input, positive and negative reverse protection.
  • Sampling Rate: 3 times/second.
  • Auto Power Off: Approximately 10 minutes of inactivity.
  • Operating Temperature: 0°C to 40°C.
  • Storage Temperature: -10°C to 60°C; Humidity ≤80%.
  • Pollution Grade: 2.
  • Altitude: 0 to 2000m.
  • Battery: 3 x AAA 1.5V batteries.
  • Dimensions: 142.5mm (H) x 76mm (W) x 32mm (D).
  • Weight: 198g (standard battery included, weight varies for different models).
  • Certificates: CE/EMC/ROHS.
  • High-concerned chemical: None.
  • Battery Included: No (referring to initial purchase, user must install).
ZIBOO FT-2000W dimensions and specifications table

Figure 8: Detailed specifications for FT-1000W and FT-2000W models.

8. Application Scenarios

The ZIBOO Solar MPPT Meter is widely applicable in various fields related to photovoltaic systems:

  • Power Station Construction Units: For design, acceptance testing, and maintenance of solar power plants.
  • Quality Control Departments: To ensure the performance and quality of solar panels.
  • Manufacturers: For production testing and quality assurance of photovoltaic modules.
  • Research Units: For experimental and developmental purposes in solar energy technology.
Wide range of applications for the meter

Figure 9: Visual representation of various application areas for the solar MPPT meter.

9. Maintenance

9.1 Battery Replacement

When the low battery symbol appears on the display, it's time to replace the batteries.

  1. Ensure the meter is powered off and disconnected from all solar panels and test leads.
  2. Locate the battery compartment on the back of the device.
  3. Unscrew the battery cover screws.
  4. Remove the old AAA 1.5V batteries and insert three new ones, ensuring correct polarity.
  5. Securely close the battery compartment and tighten the screws before resuming use.

9.2 General Care

  • Clean the device with a soft, dry cloth. Do not use abrasive cleaners or solvents.
  • Store the meter in a cool, dry place away from direct sunlight and extreme temperatures.
  • If the device will not be used for an extended period, remove the batteries to prevent leakage.
  • Only authorized and professionally experienced technicians should open the machine casing for repair. Contact official after-sales service if the product malfunctions.

10. Troubleshooting

ProblemPossible CauseSolution
Meter does not power on.Dead or incorrectly installed batteries.Replace batteries with new AAA 1.5V batteries, ensuring correct polarity.
"OL" displayed on screen.Measurement exceeds the meter's range (e.g., voltage, current, or power too high).Disconnect immediately. Ensure the solar panel's specifications are within the meter's limits (FT-1000W: Max 1000W/80V/35A; FT-2000W: Max 2000W/120V/35A).
High-voltage lightning symbol and buzzer alarm.Voltage exceeding safe limits.Disconnect immediately. Verify connections and ensure panel voltage is within safe operating range.
Temperature symbol displayed, testing stops.Internal temperature exceeds 60°C.Allow the meter to cool down in a shaded area before resuming operation.
Inaccurate readings.Low battery, faulty test leads, or incorrect connection.Replace batteries, inspect test leads for damage, and re-check all connections for correct polarity.

11. User Tips

  • Optimize Panel Placement: Use the meter to test different angles and positions of your solar panels to find the optimal orientation for maximum power output, especially when dealing with shading.
  • Troubleshoot Cables: The meter is effective for identifying issues with solar cables, such as faulty MC4 connectors or internal cable damage.
  • Assess Used Panels: When purchasing used solar panels, this tester can quickly verify their performance and ensure they meet your expectations.
  • Versatile Connections: The included alligator clip test leads (with FT-2000W) are very useful for testing panels that do not have standard MC4 connectors or use other patterns.
  • Ease of Use: The meter is designed for straightforward operation; simply connect and press a button to get your readings.

12. Frequently Asked Questions (FAQ)

Q: Can this item measure DC Voltage of 300V or more?
A: No, the ZIBOO Solar MPPT Meter has a maximum voltage measurement capacity of 80V for the FT-1000W model and 120V for the FT-2000W model. It cannot measure voltages of 300V or higher. Attempting to do so may damage the device and pose a safety risk.

13. Warranty and Support

For product support, technical assistance, or warranty inquiries, please contact ZIBOO customer service:

  • Email: sales-support@ziboo.online
  • Telephone: +86-532-88900998

Please note that opening the device casing for repair should only be done by authorized and professionally experienced technicians. Improper repair attempts may cause damage and electric shock hazards.

14. Additional Resources

A detailed user manual in PDF format is available for download. For comprehensive information, please refer to the official PDF manual: View User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.