Kyocera DK-8720

Contents

Kyocera DK-8720 Drum Unit

Instruction Manual

1. Introduction

This manual provides essential information for the safe and effective use of your Kyocera DK-8720 Drum Unit. Please read these instructions carefully before installation and operation to ensure optimal performance and to prevent damage to the unit or your printer. The DK-8720 Drum Unit is a critical component responsible for image formation in compatible Kyocera TASKalfa series printers.

2. Safety Information

Always observe the following safety precautions:

  • Keep the drum unit out of reach of children.
  • Do not expose the drum unit to direct sunlight or strong light sources.
  • Avoid touching the surface of the drum unit, as fingerprints or scratches can affect print quality.
  • Handle the unit with care to prevent dropping or impact.
  • Store the drum unit in its original packaging until ready for installation.
  • Dispose of used drum units according to local regulations.

3. Setup and Installation

Follow these general steps to install the DK-8720 Drum Unit. Refer to your printer's specific user manual for detailed instructions, as procedures may vary slightly by model.

  1. Unpack the Drum Unit: Carefully remove the new drum unit from its packaging. Avoid touching the sensitive drum surface.
  2. Power Off the Printer: Ensure the printer is turned off and unplugged from the power outlet before beginning installation.
  3. Open the Printer Cover: Open the front cover or access panel of your Kyocera TASKalfa printer to expose the drum unit compartment.
  4. Remove the Old Drum Unit: Grasp the handle of the old drum unit and pull it out of the printer. Place it in a protective bag for proper disposal.
  5. Install the New Drum Unit: Align the new DK-8720 Drum Unit with the guides in the printer and gently push it in until it clicks into place. Ensure it is securely seated.
  6. Close the Printer Cover: Close the printer's front cover or access panel.
  7. Power On the Printer: Plug the printer back in and turn it on. The printer will typically perform a self-test and recognize the new drum unit.
Packaged DK-8720 Drum Unit box with 'Fragile! Handle with Care!' label.
Figure 1: Packaged DK-8720 Drum Unit, indicating careful handling.

4. Operating the Drum Unit

The DK-8720 Drum Unit operates automatically once correctly installed in your Kyocera TASKalfa printer. Its primary function is to transfer toner to the paper, forming the image. The printer's internal system monitors the drum unit's life and will notify you when replacement is necessary.

  • Ensure the printer's firmware is up to date for optimal compatibility and performance.
  • Always use genuine Kyocera toner cartridges with the drum unit for best results and to prevent damage.

5. Maintenance

Proper maintenance extends the life of your drum unit and ensures consistent print quality.

  • Cleaning: Do not attempt to clean the drum unit's surface with abrasive materials or solvents. If print quality issues arise, consult your printer's manual for specific cleaning procedures, which usually involve internal printer cleaning cycles.
  • Storage: If storing a new drum unit, keep it in its original, sealed packaging in a cool, dry place away from direct light and extreme temperatures.
  • Handling: When handling the drum unit, always hold it by its designated handles and avoid touching the green or blue drum surface.

6. Troubleshooting

If you encounter issues after installing or during the use of your DK-8720 Drum Unit, consider the following:

Problem Possible Cause Solution
Poor print quality (streaks, spots, faded prints)
  • Drum surface contamination
  • Incorrect installation
  • Drum unit nearing end of life
  • Low toner level
  • Perform printer's internal cleaning cycle.
  • Re-install the drum unit, ensuring it's seated correctly.
  • Check toner cartridge level and replace if low.
  • If drum unit is old, consider replacement.
Printer displays "Drum Unit Error"
  • Improper installation
  • Faulty drum unit
  • Remove and re-install the drum unit.
  • Ensure all protective materials were removed.
  • If error persists, contact support.
Printer does not recognize new drum unit
  • Incorrect installation
  • Printer not reset
  • Ensure the unit is fully seated.
  • Power cycle the printer (turn off, unplug, wait 30 seconds, plug in, turn on).

7. Specifications

Feature Detail
Model Number DK-8720
Part Numbers 302NH93061, 302NH93060
Type Drum Unit
Brand Kyocera (Original)
Origin Mainland China
High-concerned chemical None
Compatible Printer Models Kyocera TASKalfa 7052ci, 8052ci, 7053ci, 8053ci, 7353ci, 8353ci
Package Length 52 cm
Package Width 21 cm
Package Height 24 cm
Package Weight 2.0 kg

8. User Tips

  • Regular Cleaning: Periodically run the printer's automatic cleaning cycles to maintain optimal print quality and extend the life of the drum unit.
  • Environmental Factors: Keep your printer in a stable environment, avoiding excessive humidity or temperature fluctuations, which can impact drum unit performance.
  • Genuine Supplies: Always use genuine Kyocera toner and other consumables to ensure compatibility and prevent damage to the drum unit and printer.
  • Proper Disposal: When replacing the drum unit, ensure the old unit is disposed of responsibly according to local environmental regulations. Many manufacturers offer recycling programs.

9. Warranty and Support

For warranty information and technical support, please refer to the documentation provided with your Kyocera printer or contact Kyocera customer service directly. Ensure you have your printer model and the drum unit's part number (DK-8720, 302NH93061/302NH93060) available when seeking support.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.