ROBORE SF20

Contents

ROBORE SF20 Foldable Home Treadmill User Manual

Model: SF20

Introduction

Thank you for purchasing the ROBORE SF20 Foldable Home Treadmill. This manual provides essential information for the safe assembly, operation, maintenance, and troubleshooting of your treadmill. Please read these instructions carefully before use and retain them for future reference.

For a comprehensive guide, you may also refer to the official user manual PDF: User Manual (PDF).

Safety Precautions and Warning Instructions

1. Caution

To avoid any injuries, please read this manual carefully before using the treadmill.

2. Safety Notice

  • Place the machine on a flat, stable ground. It is unsuitable for the following locations:
    1. Outdoors (The machine is specifically designed for indoor use only).
    2. Slanted ground or slanted places on a balcony.
    3. Areas exposed to direct sunlight or near heaters.
    4. Noisy environments.
  • Errors may occur if the power supply is unstable.
  • Do not use the same electrical socket with other high-power appliances like computers or air conditioners.
  • It is recommended to wear sports shoes when using the machine.
  • Increase or decrease speed gradually.
  • Exercise caution with children or other objects when folding and unfolding the machine.
  • Do not place the machine near wet objects. Water drops may cause malfunctions.

3. Caution During Use

  • If you feel unwell before using, consult with your doctor or coach. The manufacturer is not responsible for injuries caused by improper use.
  • Switch off all functions and unplug the machine after use.
  • Unplug the machine before moving it or changing any parts.
  • Children, elderly individuals, and pregnant women are prohibited from using the machine.
  • Patients should consult a doctor before use.
  • Prevent water from entering the machine, especially the motor, power line, and plug.
  • Wearing long dresses or other unsuitable clothing during use may cause danger.
  • Avoid using the machine in enclosed spaces, areas with poor air circulation, or places with flammable materials.
  • Do not place any objects on the machine.
  • Keep the plug away from heated surfaces or fire sources.
  • Do not stand directly on the belt when starting the machine.
  • Do not disassemble the machine without professional guidance.
  • Ensure the running belt is securely fastened before use.

Assembly Instructions

The ROBORE SF20 treadmill is designed for minimal assembly. It comes ready to use right out of the box. However, some minor adjustments or securing steps may be required.

Packing List

  • Treadmill machine: 1
  • Allen wrench 5mm: 1
  • Safety lock: 1
  • User manual: 1
  • Knob M8*50: 2
  • Knob M8*37: 2

General Assembly Steps

  1. Step 1: Unpacking and Initial Setup

    Open the package and carefully remove all assembly materials. Lay the main part of the treadmill on the ground to expand the fixed column.

    Treadmill in folded position (Figure 1)Treadmill in unfolded position (Figure 2)

    Figure 1: Treadmill in folded position. Figure 2: Treadmill in unfolded position.

  2. Step 2: Securing the Column and Display Window

    • Screw the lower part of the column with Knob M8*50 to fix the column.
    • Screw the upper part of the column with Knob M8*37 to fix the display window.
    Diagram showing where to screw knobs M8*50 and M8*37 (Figure 3)

    Figure 3: Securing the column and display with M8*50 and M8*37 knobs.

  3. Step 3: Safety Lock and Stability Check

    • Attach the red safety lock switch. Failure to do so will result in an E7 error.
    • During exercise, attach the safety clip to your clothing near the waistline. In case of complications, a strong tug on the safety lanyard will immediately stop the running belt.
    Close-up of the treadmill console with safety lock in place (Figure 4)

    Figure 4: Safety lock placement on the console.

    Attention: If the treadmill wobbles, adjust the two adjustable knobs located under the treadmill base.

    Diagram showing the adjustable knob under the treadmill base (Figure 5)

    Figure 5: Location of adjustable knobs for stability.

Operating Instructions

1. Window Display

The treadmill features a triple-screen display that shows the following information:

  • Time: Displays running time in manual mode or countdown in program mode.
  • Speed: Shows the current running speed.
  • Distance: Displays cumulative distance in manual mode or countdown in program mode.
  • Calorie: Shows total calories burned in manual mode or countdown in program mode.

2. Keypress Functions

  • ▶: The machine will start at 1 KM/H after 3 seconds.
  • ■: The speed will slow down until it stops.
  • +: Speed up.
  • -: Speed down.
  • 3/6: When the machine starts, press to switch speed to 3 KM/H or 6 KM/H.
  • P/M: In standby mode, press this button to cycle between manual mode and automatic programs P1-P12. Manual mode is the default operation mode.

3. Countdown Function (Time, Distance, Calorie)

In standby mode, press the P/M button again to enter the three countdown modes: Time, Distance, and Calorie. The indicator light for the current mode will be on. Use the + and - keys to adjust the countdown value. After setting, press ▶ to start.

4. Pre-set Programs (P1-P12)

The treadmill includes 12 pre-set programs (P1-P12), each with varying speed profiles over 20 time periods. The table below outlines the speed (km/h) for each program and time period.

Set the time/20 time periods - upper and lower running time (Speed: km/h)
Time Periods
Program1234567891011121314151617181920
P01 Speed23345345534544423353
P02 Speed24456466645644422541
P03 Speed24466477747744424532
P04 Speed35567757788595566443
P05 Speed24456775678854336542
P06 Speed24345487578364425432
P07 Speed23334534534533366533
P08 Speed23367746746744423442
P09 Speed24477478489944456332
P10 Speed24567546886654424433
P11 Speed34595955595555998763
P12 Speed2581077101077101066995543

5. Exercise Suggestions and Guidelines

  • Warm-up: Perform 5 to 10 minutes of warm-up before each use.
  • Breathing: Maintain coordinated breathing during exercise. If breathing becomes too fast, stop immediately.
  • Frequency: Allow 48 hours of rest for the same muscle group between workouts.
  • Load: Adjust training intensity based on individual physical fitness. Muscle ache is normal initially and will subside with continued training.
  • Diet: Exercise one hour after meals. Eat at least half an hour after training. Drink less water during exercise, especially avoiding large quantities to prevent burden on heart and kidneys.
  • Stretching Exercise: Always stretch before and after your workout. Warm muscles are easier to stretch. Perform the following stretches for 10 seconds or more per leg, repeating at the end of the workout:
    1. Downward Stretching: Slightly bend knees, slowly bend down, relax back and shoulders, touch toes. Hold for 10-15 seconds, repeat 3 times.
    2. Hamstring Stretching: Sit on a cushion, straighten one leg, place the other leg close to the inner thigh of the stretched leg, and try to touch the toes. Hold for 10-15 seconds, repeat 3 times per leg.
    3. Calf and Heel Tendon Stretching: Stand with hands on a wall or table, one foot behind. Keep back leg upright and heel down, lean towards the wall or table. Hold for 10-15 seconds, repeat 3 times per leg.
    4. Head Muscle Stretching: Hold balance with your right hand on a wall or table, extend left hand backward, grasp left ankle, and slowly pull it up to your hip until you feel tension in the front of your thigh. Hold for 10-15 seconds, repeat 3 times per leg.
    5. Sartorius Muscle (Inner Thigh) Stretching: Sit with feet facing each other, knees out, grasp feet with both hands, and pull them towards the ventral groove. Hold for 10-15 seconds, repeat 3 times.
    Diagrams illustrating various stretching exercises (Figure 1-5 for stretching)

    Figure 1-5: Visual guide for stretching exercises.

Daily Maintenance

1. Elastic Adjustment of Running Belt

Treadmills are factory-adjusted for running belt tension. However, after some use, the belt may loosen, leading to slipping during normal operation. To adjust, use the provided hex key to turn the running belt adjusting bolts (left and right) synchronously in a clockwise direction, half a circle at a time.

Note: Do not overtighten the running belt. Excessive tightness accelerates belt aging, increases motor load, and shortens bearing service life. The belt should be tight enough for normal use without slipping.

2. Deviation Adjustment of Running Belt

Running belt deviation can occur due to:

  • Unstable placement of the treadmill.
  • User's feet not being centered on the running belt during exercise.
  • Uneven force applied by the user's feet.

Minor deviations caused by human factors usually self-correct after several minutes of no-load operation. For persistent deviations, adjust the belt using the following steps:

To determine left and right, stand at the rear of the treadmill, facing the display. Make all adjustments on the rear bolt using the hex key.

  • If the belt is off-center to the LEFT: Turn the left adjusting bolt ¼ turn clockwise OR the right adjusting bolt ¼ turn counterclockwise. This moves the running belt to the right.
  • If the belt is off-center to the RIGHT: Turn the left adjusting bolt ¼ turn counterclockwise OR the right adjusting bolt ¼ turn clockwise. This moves the running belt to the left.
Diagram showing how to adjust the running belt when it's off-center to the left or right

Diagram: Running belt deviation adjustment.

Important:

  • Do not turn the adjusting bolt more than ¼ turn at a time. Overtightening can damage the treadmill.
  • Recheck the alignment by repeating the steps.
  • Running belt deviation is not covered by warranty and is user-maintained. Timely adjustment is crucial to prevent serious damage and extend service life.

Troubleshooting

This section provides solutions for common issues you might encounter with your treadmill.

Serial NumberError CodeDescriptionOverhaul/Solution
1E02Hall detection error reported.1. Detect Hall wire terminals; 2. Change the motor; 3. Change the control.
2E03Overstream error reported.1. Replace the control.
3E04Overvoltage error reported.1. Detect external input mains; 2. Replace the down control.
4E05Undervoltage error reported.1. Detect external input mains; 2. Replace the down control.
5E06Overload error reported.1. Detect whether the running resistance is abnormal; 2. Change the motor; 3. Change the control.
6E08Downcontrol overheat error.1. Detect whether the running belt resistance is abnormal; 2. Change down control.
7E09Lift motor detection error reported.1. Detect whether the ascension motor is abnormal.
8E11Uvw three wire simultaneously open circuit error.1. Detect whether the motor wire is abnormal; 2. Change the motor; 3. Change the control.
9E12The lower control cannot receive the relay signal error.1. Change the control.
10E13Relay cannot receive digital watch signal error.1. Detect whether the communication line is abnormal; 2. Change down control; 3. Replace the watch.
11E07Error reported when safety lock comes off.1. Detect whether the communication line is abnormal; 2. Change down control; 3. Change the table.

Specifications

The following table details the technical specifications of the ROBORE SF20 Treadmill.

CategoryDetail
General
  • Brand: ROBORE
  • Type: Treadmill
  • Model: SF20
  • Color: Black
Electrical
  • Rated Voltage: 220V-240V
  • Rated Frequency: 50Hz
  • Power Consumption: < 0.5 kWh
  • Power Supply Requirement: Not 50Vac or 75Vdc or Higher
Performance
  • Rated Peak Value: 3.0HP Brushless Motor
  • Noise Level: < 45 dB
  • Motor Service Life: 3500 Hours (8-10 Years)
  • Speed Range: 1-12 KM/H (Walking: 1-3 km/h, Jogging: 3-6 km/h, Running: 6-12 km/h)
  • Incline: 15% Manual Incline
Running Belt
  • Type: 7-Layer Non-Slip Diamond Texture Running Belt
  • Dimensions: 97 × 40 cm
  • Running Belt Length: 80-120cm (General category)
  • Running Belt Width: 30-50cm (General category)
Features
  • Shock Absorption System: 8 Built-in Shock Absorbers + 2 External Shock-Absorbing Mats (Triple Shock Absorption)
  • Maximum Load Capacity: 136 kg / 265 lbs
  • Fold: Yes
  • Folded Thickness: 10.5 cm
  • Mobility: Built-in Transport Wheels
  • Control Method: Button Control
  • Display: Triple-Screens Display
  • Tablet Holder Angle: 135° Golden Elevation
  • Screen: No (dedicated screen beyond the display)
  • With Speakers: No
  • Bluetooth Connection: No
  • Adjustable Slope: Yes (15% Manual Incline)
  • Training Site: Legs, Muscle Relex Apparatus, Foot
  • Type of Sports: Cardio Training
Dimensions & Weight
  • Product Weight: 18.5 kg
  • Package Weight: 21.3 kg
  • Product Size (L x W x H): 113 × 55.3 × 100 cm
  • Package Size (L x W x H): 118 × 58 × 11.5 cm
Origin
  • Mainland China

User Tips

  • Check Dimensions: While the treadmill is compact, always verify the running belt dimensions (97x40 cm) against your stride length, especially if you are tall or plan to run at higher speeds.
  • Quiet Operation: Users report the motor is quiet, making it suitable for home use without excessive noise disruption.
  • Tablet Holder Stability: Ensure the tablet holder is securely fastened and stable before placing your device to prevent it from falling during exercise.
  • Assembly Check: During assembly, double-check all bolt threads and connections to ensure they are properly aligned and secured.
  • Folding and Storage: The treadmill folds easily and takes up minimal space (10.5 cm thick when folded), making it convenient for storage in small areas.

Frequently Asked Questions (FAQ)

Q: Is the tablet stand stable?
A: The tablet stand is designed for stability. Ensure it is properly set at the 135° Golden Elevation angle for optimal support. If you experience wobbling, check the adjustable knobs under the treadmill base for stability.
Q: What should I do if a bolt thread is missing or damaged during assembly?
A: If you encounter a missing or damaged bolt thread, do not force the assembly. Contact customer support for assistance or replacement parts. Ensure all components are in good condition before proceeding with assembly.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.