1. Introduction
1.1 Preface
Thank you for purchasing this product, which is a dual band/dual display/dual watch. This easy-to-use radio will deliver secure, instant, and reliable communications at peak efficiency. Please read this manual carefully before use. The information presented herein will help you to derive maximum performance from your radio.
1.2 Regulations and Safety Warnings
- WARNING! European Users should note that operation of this unit in Transmit mode requires the operator to have a valid Amateur Radio License from their respective Countries Amateur Radio Licensing Authority for the Frequencies and Transmitter Power levels that this Radio transmits on. Failure to comply may be unlawful and liable for prosecution. Refer to the “EU” specification guide 2014/53/EU.
- ATTENTION! When programming the radio, start by reading the factory software data, and then rewrite this data with your frequency etc., to a new saved code plug, otherwise errors may occur. You can use the programming cable with a PC to program the authorized frequency, bandwidth, power, etc. your programming must comply with your FCC (or EU other country) license certification.
- ATTENTION! Before using this product, read the RF Energy Exposure and Product Safety Guide that ship with the radio which contains instructions for safe usage and RF awareness and control for compliance with applicable standards and regulation.
- PMR446, FRS, GMRS, MURS: You may be tempted to use PMR446 (in Europe) or FRS, GMRS, MURS (in the USA) frequencies. Do note however that there are restrictions on these bands that make this transceiver illegal for use.
- FCC RF Exposure: Do not use the radio with a damaged antenna. If a damaged antenna comes into contact with the skin, a minor burn may result. Please contact your local dealer for a replacement antenna. For hand-held operation, the radio should be held 1 inch from the user's face. For body-worn operation, use the supplied belt-clip accessory.
1.3 Main Features
- Scanning receiver frequency range: FM 76-108 MHz; AM 108-136MHz, VHF 136-174MHz, 220-260MHz, UHF350-390MHz, 400-520MHz
- One touch search frequency, easy pairing and grouping (copying channel configuration parameters)
- Frequency step, selectable between 2.5K | 5.0K | 6.25K | 10.0K | 12.5K | 20.0K | 25.0K | 50.0K
- Frequency hopping and scramble functions to keep your call privacy confidential
- 1.77" TFT large screen, full keyboard, fully open menu operation
- Channel scan, frequency scan, and three scan and recovery methods: TO, CO, and SE
- Up to 999 memory channels.
- Power-on password management function
- DTMF encoder and DTMF manual dial
- VOX (voice activated transmit).
- Alarm function.
- High or low power selectable.
- Programmable repeater offset.
- Transmission time-out timer.
- LED flashlight.
- End of transmission tone, aka "Roger Beep"
- Broadcast FM radio receiver 76-108 MHz
- Dual watch / Dual reception/ Dual-band handheld transceiver
- High Capacity Lithium-Ion battery.
- Stopwatch function
- Display illumination programmable via keypad.
- Function beep on the keyboard.
- Battery save function.
- Busy channel lock out.
- Ten (10) levels of Squelch adjustment.
- Two (2) pins for Kenwood accessory port
- Support NOAA weather reception function in the United States and Canada
The M version supports AM108-136 scanning reception, and voice scrambling functions. The L version does not support AM108-136 scanning reception, and voice scrambling functions. There is no voice scrambling option in the function menu.
2. Package Contents
The package should contain the following items:
- 1 x Radio
- 1 x Antenna
- 1 x Li-Ion battery pack
- 1 x Belt clip
- 1 x Hand Strap
- 1 x Type-C Cable
- 1 x Product Manual (this document)
If any item is missing, please verify with your dealer.
3. Setup
3.1 Charging the Battery Pack
The Li-ion battery pack is not charged at the factory; please charge it before use. For best performance, fully charge/discharge the battery two or three times.
Use Caution with the Li-ion Battery
- Do not short the battery terminals or throw the battery into a fire.
- Never attempt to remove the casing from the battery pack.
- Charge the battery between 5℃-40℃ (40°F - 105°F).
- Turn off the radio before inserting it into the charger.
- Do not cut off power or remove the battery during charging until the green light is on.
- Do not recharge a fully charged battery.
- Do not charge the battery or radio if it is damp.
How to Charge
- Plug the AC adaptor into an AC outlet, then plug the cable into the DC jack on the back of the charger. The indicator light blinks orange.
- Plug the battery or radio into the charger. Ensure good contact with charging terminals. The indicator turns red.
- Charging takes approximately 2-5 hours. When the lamp lights green, charging is complete.
LED Indicator Status during Charging
| Status | LED |
|---|---|
| No Battery | Green and red alternately flashing |
| Charge Normally | Red |
| Fully Charged | Green |
| Trouble (battery too warm, short-circuited) | Red blinks fast for a long time |
How to Store the Battery
- Store at 80% discharged.
- Keep in low temperature and dry environment.
- Keep away from hot places and direct sunlight.
Using the Type-C USB Charger
The Type-C USB charger allows convenient charging of your Li-ion battery pack.
- Ensure your radio is turned OFF.
- Plug the Type-C USB cable into the Type-C charging port on your battery. Connect the other end to a wall power outlet.
- An empty battery will be fully charged in 4 hours.
- The battery meter on the LCD will move to indicate charging.
Note: It is recommended to power OFF your radio while charging. For optimal battery life, remove the radio from the charger within 6 hours.
3.2 Installation of Accessories
Before the radio is ready for use, attach the battery pack and charge the battery.
Installing / Removing the Antenna
- Installing: Screw the antenna into the connector on the top of the transceiver by holding the antenna at its base and turning it clockwise until secure.
- Removing: Turn the antenna counter-clockwise to remove it.
Installing the Belt Clip
- Installing: Remove the two parallel screws above the battery on the back of the radio. Thread them through the holes on the belt clip and screw them back into the radio body.
- Removing: Unscrew counter-clockwise to remove the belt clip.
Installing the Battery Pack
Before attaching or removing the battery, ensure your radio is turned off by turning the power/volume knob all the way counter-clockwise.
- Align the battery in parallel with the radio body, with the lower edge of the battery about 1-2cm below the edge of the radio.
- Slide the battery upward along the guide-rails until you hear a click as it locks in place.
Removing the Battery Pack: Press the battery release above the battery pack as you slide the battery downward.
Installing the Additional Speaker/Microphone (Optional)
Pry open the rubber MIC-Headset jack cover and then insert the Speaker / Microphone plug into the double jack. The diagram for this connection shows a 2.5mm jack for the microphone and a 3.5mm jack for the speaker, with a PTT button and a 10uF capacitor and +5V connection for the microphone circuit.
4. Radio Overview
4.1 Buttons and Controls of the Radio

The image above illustrates the various buttons and controls of the radio. For detailed identification, please refer to the numbered list below:
- Power/Volume knob
- SK1- Broadcast FM and Alarm key
- PTT key
- VFO/MR mode key
- Status LED
- SK2-Flashlight and Monitor key
- A / B select key
- Menu Key
- Numeric keypad
- Antenna jack
- LED flashlight
- Color LCD
- Accessory jack
- Speaker and microphone
- One-Touch search key
- Exit Key
- Up/Down navigation keys
- Type-C charging port
- Type-C charging indicator
- Battery release latch
4.2 LCD Display Icons
The LCD display provides various status indications through icons:
| Icon | Description |
|---|---|
| RSSI | Squelch Open/Close Indicator |
| H/L | Transmit power level indicator (High/Low) |
| D | DCS enabled |
| C | CTCSS enabled |
| + | Enables access of repeaters in VFO/Frequency Mode. TX will be shifted higher in frequency than RX. |
| - | Enables access of repeaters in VFO/Frequency Mode. TX will be shifted lower in frequency than RX. |
| D | Dual watch enabled |
| . | Keypad lock enabled |
| VOX icon | VOX enabled |
| N | Narrowband enabled |
| Battery icon | Battery level indicator |
| R | Reverse function enabled |
| Triangle icon | Indicates active band or channel |
| SCR | The voice scramble function has been activated |
Battery Level Indicator
When the battery level indicator shows an empty battery icon, the battery is depleted. The radio will beep periodically, flash the backlight, and announce "Low Voltage" (if voice prompts are enabled), indicating it needs charging.
5. Basic Operations
5.1 Power On/Off
- Turning On: Rotate the Volume/Power knob clockwise until you hear a "click". The display will show a message or flash the LCD, then display a frequency or channel. If voice prompt is enabled, it will announce "frequency mode" or "channel mode".
- Turning Off: Turn the Volume/Power knob counter-clockwise all the way until you hear a "click".
5.2 Adjusting the Volume
Rotate the volume/power knob clockwise to increase volume, and counter-clockwise to decrease. Use the monitor function (press [SK2] below the PTT) to adjust volume to the un-squelched static.
5.3 Main Band/Sub Band Select
In standby mode, press the [A/B] key to switch between A (upper) and B (lower) displays. The selected display's frequency or channel becomes active for listening and transmitting. To save frequencies to channel memory, you must be on the A display.
5.4 VFO/Channel Switch
Press the [VFO/MR] key to switch between Frequency (VFO) mode and Channel (MR) mode.
- In Channel (MR) mode, the channel number is displayed on the right.
- In Frequency (VFO) mode, 'VFO' is displayed on the right.
5.5 Making a Call
Note: Press the [A/B] key to switch the main channel if two channels are shown on the display. In standby mode, press [VFO/MR] to switch between VFO and MR mode.
- Channel Mode Call: After selecting a channel, hold down the [PTT] key to initiate a call. Speak into the microphone with normal tone. The red LED will be on.
- Frequency Mode Call: Press [VFO/MR] to switch to frequency mode, input the working frequency, and hold [PTT] to transmit. The red LED will be on.
- Receive a Call: When you release the [PTT] key, you can answer without action. The green LED will be on when receiving a call.
Note: Keep the microphone 2.5 cm to 5 cm from your mouth during transmission for best reception volume.
5.6 Using the Flashlight
Press the [SK2] key momentarily to turn on the LED flashlight. Another momentary press will flash the LED. Another momentary press turns the flashlight off.
5.7 Emergency Alert
To activate the emergency alert, press and hold the [SK1] key for 3 seconds. The radio will send a loud siren sound and the flashlight will flash. Press [SK1] again to exit. WARNING: Only use this feature in actual emergencies.
5.8 FM Radio (FM)
The radio can listen to FM frequencies from 65-108MHz. The key switches between 65-75 MHz and 76-108 MHz bands.
- In frequency or channel mode, press [SK1] to turn on the radio.
- Select the desired radio frequency with the Up/Down keys or input the frequency. Press the # key to automatically search for a station.
- Press [SK1] to exit FM radio.
Note: While listening to FM, if an A/B receiving signal is detected, the radio will automatically switch to that frequency/channel for normal transmitting/receiving. It will switch back to FM radio mode when the signal disappears.
5.9 Monitor
In standby, press and hold the [SK2] key to enter Monitor. This allows monitoring weak signals. Release [SK2] to turn off speakers and return to standby. If no signal, it will emit noise when [SK2] is pressed.
5.10 Keypad Lock
To enable or disable the keypad lock, press and hold the * key for about two seconds. The keypad can also be set to lock automatically after ten seconds via the menu.
5.11 Frequency Reversal
A short momentary press of the # key enables the reverse function. This reverses your transmit and receive frequencies, useful for listening to a repeater's input frequency. The screen will display "R" in the top row.
5.12 TX Repeaters Tone
Press [PTT] + [SK2] key to send a 1750Hz repeaters tone. This is useful for communications through repeaters. This function works even if the keypad lock is enabled.
5.13 One Touch Frequency Search
- The radio acts as a receiver. Press and hold the # key; the screen will display "SEARCH SEARCH...".
- If a strong, stable signal is received, the frequency will be displayed. If CTCSS or DCS is present, its value will be shown; otherwise, "NONE" is displayed.
- Press the MENU key to save the Search frequency and CTCSS or DCS to a channel.
Note: During frequency Search, press the # key to switch between UHF or VHF bands.
5.14 Weather Radio/Scan Weather Channel
The radio has a NOAA Weather Radio function to receive weather reports and scan NOAA channels.
- To turn on NOAA Weather Scan, press the [0sQL] key for 3 seconds. The NOAA icon appears, and the radio enters Weather band mode.
- Press and hold the # key for 3 seconds to start automatic scanning of all 10 channels. It will stop on active channels. Pressing and holding # again during a scan will stop it.
- After stopping NOAA weather scan, you can manually select the weather channel using the Up/Down keys.
- To exit Weather Radio broadcast mode, press the EXIT key or [PTT] key.
Note: Weather Channels Wx 1 Thru 10 are Receive-only channels for NOAA and Canadian weather broadcasts. You cannot transmit on these channels.
6. Advanced Features
6.1 Working the Menu System
For a complete reference on available menu items and parameters, see Appendix B, Menu definitions. If your radio is set to Memory (MR) mode, certain menu items (STEP, TXP, W/N, CTCSS, DCS, S-CODE, PTT-ID, BCL, SFT-D, OFFSET, MEM-CH) will not take effect.
Basic Use (with Arrow Keys)
- Press the MENU key to enter the menu.
- Use the Up/Down keys to navigate between menu items.
- Once you find the desired menu item, press MENU again to select it.
- Use the Up/Down keys to select the desired parameter.
- To confirm your selection, press MENU. To cancel changes, press EXIT.
- To exit the menu at any time, press the EXIT key.
Using Shortcuts (Numerical Keypad)
Every menu item has a numerical value for direct access. The menu is organized with common functions at the top.
- Press the MENU key to enter the menu.
- Use the numerical keypad to enter the number of the menu item.
- To enter the menu item, press the MENU key.
- For parameters, use arrow keys or numerical keypad for shortcuts.
- To confirm selection, press MENU. To cancel changes, press EXIT.
- To exit the menu at any time, press the EXIT key.
6.2 Scanning
The radio features a built-in scanner for VHF and UHF bands. In VFO mode, it scans in steps according to your set frequency step. In Channel (MR) mode, it scans your channels. To enable the scanner, press and hold the # key for about two seconds. Press and hold # again to exit scanning mode. Dual Watch is inhibited while scanning.
Scanning Modes
The scanner can be configured for Time, Carrier, or Search operation:
- Time Operation (TO): Scanner stops when it detects a signal, then resumes after a factory preset time.
- Carrier Operation (CO): Scanner stops when it detects a signal, then resumes after a preset time with no signal.
- Search Operation (SE): Scanner stops when it detects a signal. To resume, press and hold the # key again.
Frequency Scanning
- In frequency mode, press # for more than 2 seconds to start scanning.
- Change scanning direction with Up/Down keys.
- Press # to stop scanning.
Channel Scanning
- In channel mode, press # for more than 2 seconds to start scanning.
- Change scanning direction with Up/Down keys.
- Press # to stop scanning.
Scan CTCSS
Scans frequencies with CTCSS tone enabled. In standby mode, press MENU then 14. Press MENU again to start scanning. This function cannot be activated in Channel mode and only starts when the receiving band detects a signal.
Scan DCS
Scans frequencies with DCS code enabled. In standby mode, press MENU then 15. Press MENU again to start scanning. This function cannot be activated in Channel mode and only starts when the receiving band detects a signal.
6.3 Manual Programming (Channels Memory)
The radio features 999 memory channels. Each can hold: Receive and transmit frequencies, transmit power, group signaling information, bandwidth, ANI/PTT-ID settings, and a six-character alphanumeric identifier or channel name.
Frequency Mode vs. Channel Mode
In standby mode, press [VFO/MR] key to switch between frequency (VFO) mode and channel (MR) mode.
Programming a Channel Repeater Offset with CTCSS Tone (Example)
To program a new memory in Channel 10 with RX = 432.55000 MHz, TX = 437.55000 MHz (a +5 Offset), and TX CTCSS tone 123.0:
- Press MENU to switch between menus.
- Press [VFO/MR] to set the radio to VFO mode.
- Enter MENU 3110 to delete prior data in channel 10.
- Enter MENU 1230 to select desired TX encode tone.
- Enter RX frequency (e.g., 43255000).
- Enter MENU 3010 to enter the desired channel (10) and add RX.
- Enter TX frequency (e.g., 43755000).
- Enter MENU 3010 to enter the same channel (10) and add TX.
- Press [VFO/MR] to return to MR mode.
Programming a Simplex Channel with CTCSS Tone (Example)
To program a new memory in Channel 10 with RX = 432.6625 MHz and TX CTCSS tone 123.0:
- Press MENU to switch between menus.
- Press [VFO/MR] to set the radio to VFO mode.
- Enter MENU 3110 to delete prior data in channel 10.
- Enter MENU 1230 to select desired TX encode tone.
- Enter RX frequency (e.g., 43266250).
- Enter MENU 3010 to enter the desired channel (10) and add RX.
- Press [VFO/MR] to return to MR mode.
6.4 Repeaters Programming
These instructions assume you know your repeater's transmit and receive frequencies and are authorized to use it.
- Press [VFO/MR] to set the radio to VFO mode.
- Use the numeric keypad to enter the repeater's output (your receiving) frequency.
- Press MENU to enter the menu.
- Enter 29 on the numeric keypad for frequency offset.
- Press MENU to select.
- Use the numerical keypad to enter the specified frequency offset (see "29 OFFSET - Frequency shift amount" for details).
- Press MENU to confirm and save.
- Enter 28 on the numeric keypad for offset direction.
- Use the Up/Down keys to select + (positive) or - (negative) offset.
- Press MENU to confirm and save.
- Optional: Save to memory (see "Manual programming"), set up CTCSS (see "CTCSS" for details).
- Press EXIT to exit the menu. You should now be able to make a test call through the repeater.
Note: If you experience problems, check your settings or contact your dealer.
6.5 VOX (Voice Operated Transmit)
This function allows hands-free conversations. Speak into the microphone to activate transmission. In standby mode, press MENU then 7. The screen displays "VOX". Press MENU to enter the function. Use Up/Down keys to turn off VOX or select level (1-10). Press MENU to confirm. Press EXIT to return to standby mode. Level 1 is least sensitive, 9 is most sensitive. VOX is not enabled in Scan or FM Radio mode.
6.6 Dual Watch
The radio features Dual Watch functionality (single receiver) to monitor two channels at once. The transmit frequency can be locked to one of the two monitored channels.
Enabling or Disabling Dual Watch Mode
- Press MENU to enter the menu.
- Enter 7 on the numerical keypad for Dual Watch.
- Press MENU to select.
- Use Up/Down keys to enable or disable.
- Press MENU to confirm.
- Press EXIT to exit the menu.
6.7 Stopwatch Timer
In standby mode, press MENU then 44. The screen displays "STOP WATCH". Press MENU to enter the function. Use Up/Down keys to enable (ON) the function, then press MENU for confirmation. To return to standby mode, press EXIT. When ON, press MENU to start/pause counting. To exit, stop counting first, then press EXIT.
6.8 Scrambler
The scrambler protects communications by voice inversion. In standby mode, press MENU then 45. The screen displays "SCRAMBLE". Press MENU to enter the function. Use Up/Down keys to select scramble mode (MODE1 to MODE3) to activate. The "SCR" icon will appear on the display.
6.9 DTMF (Dual-Tone Multi-Frequency)
DTMF is an in-band signaling method using dual sinusoidal signals. It's used for automation systems and remote control, such as activating repeaters. The numerical keys, *, and # correspond to DTMF codes. A, B, C, and D codes are located on the Up, Down, MENU, and EXIT keys respectively. To send DTMF codes, press the key(s) while holding down the PTT key. This works even with keypad lock enabled.
6.10 Customization
The radio allows customization of visual and audible features.
Display Backlight (ABR) - Menu 7
In standby mode, press MENU then 7. The screen displays "ABR". Press MENU to enter. Use Up/Down keys to select always on/required delay time (ON/5sec/10sec/15sec/20sec). Press MENU to confirm. Press EXIT to return to standby.
Beep Prompt (BEEP) - Menu 8
If enabled, you hear a beep tone every time a key is pressed. In standby mode, press MENU then 8. The screen displays "BEEP PROMPT". Press MENU to enter. Use Up/Down keys to turn ON/OFF. Press MENU to confirm.
Voice Function (VOICE) - Menu 17
In standby mode, press MENU then 17. The screen displays "VOICE". Press MENU to enter. Use Up/Down keys to select OFF/ON. Press MENU to confirm. Press EXIT to return to standby.
Language of the Menu (LANGUAGE) - Menu 18
This section shows the language of the MENU (English). In standby mode, press MENU then 18. The display shows "LANGUAGE".
Working Mode (MDF-A) - Menu 24
The radio has four working modes: Frequency (FREQ), Channel (CH), Channel name (NAME). To switch, in standby mode, press MENU then 24. Select desired mode with Up/Down keys. Press MENU to confirm.
Roger Beep, End Transmission Tone (ROGER) - Menu 36
Roger Beep can be enabled/disabled (OFF/ON). In standby mode, press MENU then 36. The screen displays "ROGER". Press MENU to enter. Use Up/Down keys to select OFF/ON. Press MENU to confirm. Press EXIT to return to standby.
Power On Message (POWER ON MSG) - Menu 40
Customize the welcome message displayed when the radio is switched on. Options include: VOLTAGE, MESSAGE, LOGO, MODEL NAME. In standby mode, press MENU then 40. The display shows "POWER ON MSG". Press MENU to enter. Use Up/Down keys to select option. Press MENU to confirm. Press EXIT to return to standby.
Power On Password (POWER ON PWD) - Menu 43
Enable a password to be entered when the radio is turned on. In standby mode, press MENU then 43. The display shows "POWER ON PWD". Press MENU to enter. Use Up/Down keys to enable/disable (ON/OFF). Press MENU to confirm. Press EXIT to return to standby. If enabled, the radio will display "Input Password" at startup.
Reset - Menu 42
Two reset modes: VFO (resets all settings except channels) and ALL (resets all settings). In standby mode, press MENU then 42. The screen displays "RESET". Press MENU to enter. Use Up/Down keys to select VFO or ALL. Press MENU to confirm. The display shows "Sure to reset?". Press MENU again to confirm. The transceiver will turn off and reboot.
7. Technical Specifications
| Feature | Specification |
|---|---|
| Receiver Frequency | FM 76-108 MHz; AM 108-136MHz, VHF 136-174MHz, 220-260MHz, UHF 350-390MHz, 400-520MHz |
| Transmission Frequency | 144-148 & 420-450MHz (America version) 144-148 & 430-450MHz (Canadian version) |
| Channel Spacing | 25.0KHz(Wide)/12.5KHz(Narr) |
| Memory Channel | 999 Groups |
| Operation Voltage | DC 7.4 V ±10% |
| Transmission current | ≤2800mA |
| Receive Sensitivity | 0.25μV (12dB SINAD) |
| Rated Audio Power Output | 1W @16 ohms |
| Receive current | ≤380mA |
| Connection for accessories | 2 pin Kenwood jack |
| Antenna impedance | 50 Ohm |
Note: All specifications may be modified without prior notice or liability. The M version supports AM108-136, Police350-390MHz scanning reception, and voice scrambling functions. The L version does not support AM108-136, Police350-390MHz scanning reception, and voice scrambling functions.
8. Troubleshooting Guide
This section provides solutions for common issues you might encounter.
| Phenomena | Analysis | Solution |
|---|---|---|
| You cannot turn on the radio. | Battery improperly installed, power run out, or dirty/damaged contacts. | Remove and reattach battery. Recharge or replace battery. Clean battery contacts. |
| During receiving, voice is weak or intermittent. | Low battery voltage, low volume, loose antenna, or blocked speaker. | Recharge battery. Increase volume. Turn off radio, remove/reattach antenna. Clean speaker surface. |
| You cannot communicate with other group members. | Inconsistent TX/RX frequency/signaling type, or too far from others. | Verify TX/RX frequency/signaling type. Move towards other members. |
| You hear unknown voices or noise. | Interference from other radios, or radio in analog mode without signaling. | Change frequency or adjust squelch level. Request dealer to set signaling. |
| You are unable to hear anyone because of too much noise and hiss. | Too far from others, unfavorable position (blocked by buildings/underground), or external disturbance. | Move towards other members. Move to open/flat area, restart radio. Stay away from interfering equipment. |
| The radio keeps transmitting. | VOX may be turned on or headset not installed. | Turn off VOX function. Check headset is in place. |
Note: If these solutions do not fix your problems, please contact your dealer for technical support.
9. User Tips
No specific user tips were available from reviews or Q&A content for this product.
10. Warranty and Support
For tutorials, support, and more information, please visit the official Baofeng website: www.baofengradio.com.
A detailed User Manual in PDF format is also available for download: User Manual (PDF).
11. Disclaimer
The Company endeavors to achieve the accuracy and completeness of this manual, but no warranty of accuracy or reliability is given. All the specifications and designs are subject to change without notice due to continuous technological development. No part of this manual may be copied, modified, translated, or distributed in any manner without the prior written consent of the Company. We do not guarantee, for any particular purpose, the accuracy, validity, timeliness, legitimacy or completeness of the third-party products and contents involved in this manual.