1. Introduction
The SpeedyBee Mario Mini25 is a high-performance FPV drone designed for freestyle racing and DIY enthusiasts. It features an innovative modular design that allows for quick assembly and disassembly without tools, enhancing maintenance efficiency. The drone integrates a powerful AIO flight controller, robust motors, and offers compatibility with advanced image transmission systems like the DJI O4 Air Unit Pro.
Key Features:
- Innovative snap-on modular design for tool-free assembly/disassembly.
- Highly integrated AT32F435 AIO Flight Controller with built-in ELRS 2.4G receiver.
- Powerful Bee Storm 1303.5 6660KV brushless motors.
- 25A 4-in-1 32bit (OX32) ESC.
- Speedybee APP for convenient wireless tuning via Bluetooth.
- Compatibility with DJI O4 Air Unit Pro / O4 Air Unit image transmission systems.
- Optional propeller guards for enhanced protection, especially for beginners.
2. Safety Information
⚠ Disclaimer: For recreation use only. Illegal modification of drones/planes is prohibited. Please also pay attention to the relevant laws and regulations on the use of drones/planes in your country/area to ensure legal use.
Always operate the drone in a safe environment, away from people, animals, and obstacles. Ensure all components are securely fastened before flight. Do not operate in adverse weather conditions. Always maintain visual line of sight with your drone.
3. Package Contents
The Mario Mini25 is available in various kits. Please refer to your specific kit for exact contents. Common components and kit-specific items are listed below:
Common Components:
- Mario mini25 Battery strap x2
- H1.5 Hex Screwdriver x1
- Mario mini25 Outer Shell Buckle x2
- HQProp RT2.5X2.1X3 Propellers (2 positive, 2 reverse) x1 set
Kit-Specific Components:
Mario Mini25 Power Kit:
- 5.8G Antenna x2
- Custom M2*4 Hex Screw x10
- Custom M2*6 Hex Screw x10
- Custom M2*9 Hex Screw x4
- O4 Air Unit Pro Antenna Bracket x2

Figure 3.1: Mario Mini25 Power Kit Components
Mario Mini25 O4 Air Unit Kit:
- GPS SH1.0 6P Single-Head Cable x1
- Custom M2*6 Hex Screw x10
- 12*12 GPS Fixed Double-Sided Tape x2

Figure 3.2: Mario Mini25 O4 Air Unit Kit Components
Mario Mini25 O4 Air Unit Pro Kit:
- GPS SH1.0 6P Single-Head Cable x1
- Custom M2*6 Hex Screw x10
- 12*12 GPS Fixed Double-Sided Tape x2

Figure 3.3: Mario Mini25 O4 Air Unit Pro Kit Components
Mario Mini25 Beginner Protection Ring Kit:
- Mario mini25 Protection Ring x2
- Mario mini25 Protection Ring Buckle x2
- Custom M2*7 Hex Screw x10

Figure 3.4: Mario Mini25 Beginner Protection Ring Kit Components
Mario Mini25 O4 Air Unit CNC Kit:
- O4 Air Unit CNC x1
- O4 Air Unit Lens Protector x1
- O4 Air Unit Antenna Bracket x1
- Thermal Pad 20*12mm x2
- Custom M2*3 Flat Head Hex Screw x5
- Custom M2*6 Hex Screw x4

Figure 3.5: Mario Mini25 O4 Air Unit CNC Kit Components
Optional RGB LED Strip:

Figure 3.6: RGB LED Strip (125*12mm)
4. Specifications
General Specifications:
| Component | Specification |
|---|---|
| Frame | Mario Mini25 (L115mm*W120mm*H45mm) / Diagonal: 125mm |
| AIO Flight Controller | AT32F435 |
| ESC | 25A 4-in-1 32bit (OX32) |
| Motor | Bee Storm 1303.5 6660KV |
| Gyro | ICM-42688-P |
| Receiver | Built-in ELRS2.4G |
| Bluetooth | Speedybee APP tuning |
| OSD (Analog) | No (AIO does not support OSD chip) |
| Black Box | 8MB |
| Propeller | HQProp RT2.5X2.1X3 (2 positive, 2 reverse) |
| Power Input Port | Custom XT30PW-M |
| Input Voltage | 3S LiPo/LiHV |
| Recommended Battery Port | Amass XT30ULW-F A-type |
| Recommended Battery Size | ≤ L60mm * W30mm * H20mm (Battery cable length > 45mm) |
| Recommended Battery Capacity | Li-po 3S 550mAh-650mAh (<60g) |
| GPS Support Size | 12mm*12mm (Ceramic antenna) |
| Connector | SH1.0 (6P DJI, 6P GPS, 3P BF LED & 3P S LED) |
| Camera Angle Adjustable | O4 Air Unit Pro 10-30 degrees adjustable |
| Camera Installation Size | ≤20mm |
| Image Transmission Compatibility | O4 Air Unit Pro / O4 Air Unit |

Figure 4.1: Mario Mini25 Product Configuration Parameters
Dimensions:
- Width: 120mm
- Diagonal: 125mm
- Height: 45mm (frame)
- Length: 113mm
- Motor Spacing: 75mm

Figure 4.2: Mario Mini25 Product Hardware Dimensions
Model Configuration Comparison:
| Feature | Mario Mini25 Power Kit | Mario Mini25 O4 Air Unit | Mario Mini25 O4 Air Unit Pro |
|---|---|---|---|
| Shell Color | Pure White | Rainbow | Rainbow |
| Flight Controller | Speedybee F435 AIO | ||
| ESC | Speedybee 25A OX32bit | ||
| Motor | Bee Storm 1303.5 6660KV | ||
| Propeller | HQProp RT2.5X2.1X3 | ||
| Bluetooth Tuning | Speedybee APP | ||
| Receiver | Built-in ELRS 2.4G | ||
| Image Transmission | None | O4 Air Unit | O4 Air Unit Pro |
| O4 CNC Heat Sink | Optional | Yes | None |
| Weight | 95g ±3g | 115g ±3g | 127g ±3g |
| Propeller Guard | Optional | ||
| GPS | Optional (G12 GPS module) | ||
| LED Strip | Optional (RGB LED 10 lights direct plug) | ||
| Battery | Optional (Alliance 3S 150C 650mAh LiPo battery) | ||
| Endurance | 8.5 minutes (with 100g battery) | 8 minutes (with 170g battery) | |
| Range | 135KM/h (no battery weight) | ||
| Analog OSD | Not supported | ||
Note: The power kit only supports O4 Air Unit Pro. When using O4 Air Unit, you need to purchase a heat sink and CNC module. For O4 Air Unit, please refer to the manual for installation. Endurance and range values are theoretical and may vary based on environmental conditions and flight style.

Figure 4.3: Mario Mini25 Model Configuration Comparison
5. Setup and Assembly
Modular Design Assembly:
The Mario Mini25 features an innovative snap-on modular design, allowing for tool-free quick assembly and disassembly of the fuselage and power frame. This simplifies maintenance and component replacement.
Video 5.1: Demonstration of the snap-on modular design for quick assembly/disassembly.

Figure 5.1: Innovative Minimalist Modular Design

Figure 5.2: Integrated Molded Parts for Easy Assembly
Flight Controller and ESC:
The drone comes with a highly integrated F435 AIO flight controller and a 25A 4-in-1 32bit ESC. These components are pre-installed and feature a full plug-in design for ease of use.

Figure 5.3: Highly Integrated AIO Flight Controller
Image Transmission Unit Installation:
The Mario Mini25 features a semi-open space for installing DJI O4 Air Unit Pro or O4 Air Unit. Ensure proper alignment and secure fastening. If using the O4 Air Unit, an optional CNC heat sink is recommended for optimal performance.

Figure 5.4: Top Semi-Open Image Transmission Space
Battery Connection:
Connect your 3S LiPo/LiHV battery to the custom XT30PW-M power input port. Ensure the connection is firm and secure to prevent power loss during flight. The recommended battery port is Amass XT30ULW-F A-type.

Figure 5.5: Rear View with Battery Connector
Propeller Installation:
Attach the HQProp RT2.5X2.1X3 propellers to the motors. Pay close attention to the rotation direction; ensure the two positive and two reverse propellers are installed on the correct motors as indicated in the motor diagram or flight controller software.
Optional Components:
- GPS Module: If using a G12 GPS module, install it in the designated 12x12mm space.
- RGB LED Strip: Connect the optional RGB LED strip (125*12mm) to the appropriate connector on the flight controller.
- Propeller Guards: For added protection, especially during initial flights or in confined spaces, attach the optional beginner protection rings.
6. Operating Instructions
Power On/Off:
To power on, connect a fully charged 3S LiPo/LiHV battery to the XT30PW-M port. The drone will perform a self-check. To power off, disconnect the battery.
Flight Controller Tuning:
The SpeedyBee Mario Mini25 supports wireless tuning via the Speedybee APP using Bluetooth. Download the official Speedybee APP on your smartphone and connect to the drone's Bluetooth module to adjust flight parameters, PID settings, and other configurations.
Receiver:
The drone has a built-in ELRS 2.4G receiver. Ensure your ELRS compatible radio transmitter is properly bound to the drone before attempting flight. The front-mounted ELRS T antenna helps reduce interference and improve signal quality.
OSD (On-Screen Display):
Please note that the AIO flight controller does not support an analog OSD chip. Flight data will not be displayed directly on an analog FPV feed.
Camera and Image Transmission:
The drone supports DJI O4 Air Unit Pro / O4 Air Unit for high-quality image transmission. The camera offers 4K/120fps maximum video specifications, 1080P/100fps maximum real-time quality, and a 155° ultra-wide field of view. The camera angle is adjustable from 10-30 degrees when using the O4 Air Unit Pro.

Figure 6.1: Camera Specifications and O4 Air Unit Support
Stabilization:
When equipped with the O4 Air Unit, the drone supports in-machine stabilization and Gyroflow offline stabilization for smoother footage.
7. Maintenance
General Care:
- Keep the drone clean and free from dust, dirt, and moisture.
- Avoid exposing the drone to extreme temperatures or direct sunlight for prolonged periods.
- Store the drone in a safe place to prevent physical damage.
Modular Design for Easy Maintenance:
The snap-on modular design significantly simplifies maintenance. You can quickly detach the fuselage and other components to access the internal electronics for inspection, cleaning, or replacement without needing specialized tools.
Propeller Inspection:
Regularly inspect propellers for any signs of damage, such as cracks, bends, or chips. Damaged propellers can lead to unstable flight and reduced performance. Replace them immediately if any damage is found.
Firmware Updates:
Periodically check the official SpeedyBee website or the Speedybee APP for any available firmware updates for the AIO flight controller. Keeping your firmware up-to-date ensures optimal performance and access to new features.
8. Troubleshooting
No Power:
- Ensure the battery is fully charged.
- Verify that the XT30PW-M battery connector is securely plugged into the drone.
- Check for any visible damage to the battery cable or drone's power input.
No Signal/Control:
- Confirm your ELRS compatible radio transmitter is powered on and properly bound to the drone.
- Check the integrity of the ELRS T antenna on the drone.
- Ensure there are no major obstructions between the transmitter and the drone.
Unstable Flight:
- Inspect all propellers for damage and ensure they are correctly installed (correct rotation direction).
- Check for any loose components or screws on the frame or motors.
- Connect to the Speedybee APP via Bluetooth to review flight controller settings and calibration.
Image Transmission Issues:
- Verify the DJI O4 Air Unit or O4 Air Unit Pro is correctly installed and connected.
- Ensure there are no physical obstructions blocking the image transmission signal.
- If using the O4 Air Unit, confirm the optional CNC heat sink is installed for proper heat dissipation, especially during intensive use.
9. User Tips
- Battery Selection: For optimal performance and flight time, use 3S LiPo/LiHV batteries with a capacity between 550mAh and 650mAh, ensuring the battery weight is under 60g.
- Personalization: The integrated molded fuselage is designed to be customizable. Feel free to unleash your creativity and personalize your drone with your preferred paint job.
- Beginner Protection: If you are new to FPV flying or practicing in challenging environments, consider installing the optional propeller guards to protect your drone from impacts.
- Battery Center of Gravity: The frame is designed with an optimized battery center of gravity layout to reduce rotational inertia and improve Roll/Pitch response speed. Ensure your battery is placed correctly to benefit from this design.

Figure 9.1: Optimized Battery Center of Gravity Layout
10. Warranty and Support
For warranty claims, technical support, or further assistance, please contact your retailer or visit the official SpeedyBee website. Keep your proof of purchase for warranty validation.
⚠ Disclaimer: For recreation use only. Illegal modification of drones/planes is prohibited. Please also pay attention to the relevant laws and regulations on the use of drones/planes in your country/area to ensure legal use.