1. Safety Precautions and Warnings
To prevent personal injury or damage to vehicles and/or the tool, read this user manual carefully and observe the following safety precautions at a minimum whenever working on a vehicle:
- Never use this tool for any application other than for which it was designed.
- Never alter or modify this tool in any way. Improper operation and/or maintenance of the tool, or modification of the tool could result in serious injury or death.
- There are no user serviceable parts. Have the device serviced by a qualified repair person using only identical replacement parts. This will ensure the safety of the device is maintained. Disassembling the device will void the warranty right.
- Caution: This tool contains an internal Lithium Polymer battery. The battery can burst or explode, releasing hazardous chemicals. To reduce the risk of fire or burns, do not disassemble, crush, pierce or dispose of the battery in fire or water.
- This product is not a toy. Do not allow children to play with or near this item.
- Do not expose the device to rain or wet conditions.
- Do not place the device on any unstable surface.
- Never leave the device unattended during charging process. The device must be placed on a non-flammable surface during charging.
- Handle the device with care. If the device is dropped, check for breakage and any other conditions that may affect its operation.
- Do not operate the tool in explosive atmospheres, such as in the presence of flammable liquids, gases, or heavy dust.
- Keep the tool dry, clean, and free of oil, water or grease. Use a mild detergent on a clean cloth to clean the enclosure of the device when necessary.
- People with pacemakers should consult their physician(s) before use. Electromagnetic fields in close proximity to heart pacemaker could cause pacemaker interference or pacemaker failure.
- Always perform automotive testing in a safe environment.
- Do not attempt to operate or observe the tool while driving a vehicle. Operating or observing the tool will cause driver distraction and could cause a fatal accident.
- Wear safety eye protection that meets ANSI standards.
- Keep clothing, hair, hands, tools, test equipment, and other objects away from all moving or hot engine parts.
- Operate the vehicle in a well-ventilated work area. Exhaust gases are poisonous.
- Chock the drive wheels and never leave the vehicle unattended while running tests.
- Use extreme caution when working around the ignition coil, distributor cap, ignition wires and spark plugs. These components create hazardous voltages when the engine is running.
- Put the transmission in P (for A/T) or N (for M/T) and make sure the parking brake is engaged.
- Keep a fire extinguisher suitable for gasoline, chemical, and electrical fires within the work area.
- Don't connect or disconnect any test equipment while the ignition is on or the engine is running.
RF Exposure Information and Statement
The SAR limit is 1.6 W/kg averaged over one gram of tissue. This device has also been tested against this SAR limit. This device was tested for typical body-worn operations 0mm from the body. To maintain compliance with RF exposure requirements, use accessories that maintain a 0mm separation distance between the user's body.
Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 0mm must be maintained between the user's body, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.
2. Setup
2.1 Unboxing
The package includes the main unit, an OBD diagnostic cable, a charging cable, a user manual, and a quick start guide.
Video: Unboxing and initial overview of the LAUNCH Creader Elite V2.0 (similar to V3.0) contents, including the main unit, diagnostic cable, and documentation.
2.2 Charging the Tool
There are two charging methods available:
- Via Charging Cable: Plug one end of the included charging cable into the Type-C charging port of the tool, and the other end to an external power supply device.
- Via Diagnostic Cable: Insert one end of the diagnostic cable into the DB-15 connector of the tool, and the other end to the vehicle's DLC.
Once the charging LED illuminates solid green, it indicates that the battery is fully charged.
2.3 Getting Started (Initial System Settings)
If this is the first time you have used this tool, you need to make some system settings:
- Press the power button to power it on.
- The screen displays a welcome page. Tap Start to go to the next step.
- Choose the desired system language, and tap Next step.
- Choose the desired time zone, and tap Next step to enter the WLAN setup screen.
- Slide the switch to ON. The system starts searching for all available wireless LANs. Choose the desired WLAN access point/network.
- If the selected network is open, you can connect it directly.
- If the selected network is encrypted, you have to enter the right security key (network password).
- After the network connection is done, tap Next step to configure workshop information. Input the required information, and tap Next step to go to the next step.
- Carefully read all terms and conditions of the user agreement, check the box before Agree to all the above terms, and tap OK to finish the sign-up process and navigate to the Main Menu.
2.4 Connection to Vehicle
- Turn the ignition off.
- Locate the vehicle's 16-pin Data Link Connector (DLC). Refer to Section 2.5 for typical locations.
- Plug one end of the diagnostic cable into the vehicle's DLC, and the other end to the DB-15 diagnostic connector of the tool, then tighten the captive screws.
- Turn the ignition on. The engine can be off or running.
- Press the power button for several seconds to turn the tool on and enter the Main Menu.
Notes:
- A plastic DLC cover may be found for some vehicles and you need to remove it before plugging the diagnostic cable.
- The cable connector is keyed and will only fit one way. If you have problems connecting the cable connector to the DLC, rotate the connector 180° and try again.
- Caution: Don't connect or disconnect any test equipment while the ignition is on or engine running.
2.5 Data Link Connector (DLC) Location
The DLC is typically a 16-pin connector where diagnostic code readers interface with the vehicle's on-board computer. It is usually located 12 inches from the center of the instrument panel, under or around the driver's side for most vehicles. For some vehicles with special designs, the DLC location may vary.
If the DLC cannot be found, refer to the vehicle's service manual for the location.
3. Operating Instructions
3.1 Main Menu Overview
The main menu screen includes the following function modules:
- Local Diagnose: Configure the tool to operate as a professional diagnostic tool.
- OBD II: Quick way to check for DTCs, isolate MIL cause, check monitor status, verify repairs, and perform emission-related services.
- Service Function: Offers coding, reset, relearn, and other service functions.
- Software Update: Update vehicle diagnostic software and APK.
- Mall: Subscribe to extra vehicle diagnostic software or service software not included in the tool.
- More: Includes LAUNCH Academy, Online Service, Know Your Customer, Toolbox (diagnostic software clear, firmware fix, DTC library, diagnostic record, DLC lookup, image), and Mine (saved reports, order info, system settings).
3.2 Vehicle Diagnostics
This function is specifically designed to diagnose electronic control systems of a single vehicle model. It provides comprehensive full-system code coverage and special test functions.
3.2.1 Smart Diagnostics (Auto-Detect)
This function allows you to quickly access the electronic control systems of the vehicle via decoding the Vehicle Identification Number (VIN), without manual step-by-step menu selection.
- After connection, turn the ignition key on and the system enters auto-detect mode.
- Once the system successfully obtains the VIN information of the currently identified vehicle, confirm the VIN information and tap OK to start diagnosing all available systems.
- After the diagnosis is completed, a diagnostic report will be automatically generated.
Notes:
- Ensure that the Automatic detection on connect in Settings is set as ON. Alternatively, you can also tap Local Diagnose -> AutoDetect to start the smart diagnostics manually if the Automatic detection on connect is OFF.
- A highly stable and solid network connection is recommended for successful VIN access.
3.2.2 Manual Diagnostics
If the tool cannot obtain or analyze the VIN information, you can perform vehicle diagnosis manually. In this mode, you need to execute the menu-driven command and then follow the on-screen instructions to proceed.
Flowchart for Manual Diagnostics:
- Select Local Diagnose
- Select Vehicle Manufacturer
- Select Vehicle Model
- Select Scan Mode (Automatic System Detection or Manual System Selection)
- Select Test Function (Read Version Information, Read Fault Code, Clear Fault Code, Read Data Stream, Special Function)
Notes:
- Before vehicle diagnostics, make sure the corresponding vehicle manufacturer software has been installed in your tool.
- The diagnostic menu may vary by the vehicle's make, model, and year.
3.2.3 Health Report (Quick Test)
This function enables you to quickly access all the electronic control units of the vehicle and generate a detailed report about vehicle health. Tap Health Report on the test item selection screen, the system starts scanning the ECUs. Once the scanning is complete, the report will appear, showing fault codes (marked with a cross) and normally working systems (marked with a tick).
On-Screen Buttons:
- Report: Tap to save the diagnostic result as a diagnostic report. All diagnostic reports can be accessed from More -> Mine -> My Report.
- Clear Code: Tap to clear the existing diagnostic trouble codes.
3.2.4 System Scan
This option allows you to quickly scan which systems are installed on the vehicle. After the scanning is completed, tap the system to be tested, and the test function screen is displayed.
3.2.5 System Selection
This option allows you to manually select the test system and function step by step. Tap System Selection on the test item selection screen, and tap the desired system (e.g., Engine) to enter the test function selection screen.
- Version Information: Reads vehicle module information (name, type, ECU info).
- Read Fault Code: Displays detailed information of DTC records.
- Clear Fault Code: Erases DTCs from the vehicle. Ensure ignition is ON and engine is OFF before performing.
- Read Data Stream: Retrieves and displays live data and parameters from the vehicle's ECU. Supports 3 types of display modes (Value, Graph, Combine) and recording/playback.
- Actuation Test: Accesses vehicle-specific subsystem and component tests to check actuator working status.
- Special Function: Offers coding, reset, relearn, and other service functions.
3.3 OBDII Diagnostics
This option provides a quick way to check for DTCs and perform emission-related services.
- After connecting the tool to the vehicle's DLC, tap OBD II on the main menu.
- The tool will automatically start a check of the vehicle's computer to determine the communication protocol.
- Once a communication link is established, the screen will display the Monitor Status. Tap OK to view the function list.
OBDII Function List:
- Read I/M Readiness: Checks if emissions-related systems are operating properly and ready for Inspection and Maintenance testing.
- Read Live Data: Retrieves and displays live data and parameters from the vehicle's ECU.
- Read Freeze Frame: Takes a snapshot of operating conditions when an emission-related fault occurs.
- Read Fault Code: Identifies the section of the emission control system that has malfunctioned.
- Clear Fault Code: Erases codes from the vehicle.
- Test Results: On-Board Monitoring Test: Retrieves test results for emission-related powertrain components and systems not continuously monitored.
- Control Operation of On-Board Component/System: Used to access vehicle-specific subsystem and component tests.
- Read Vehicle Information: Retrieves VIN, Calibration ID (CID), and Calibration Verification Number (CVN).
- EU OBFCM: Displays On-Board Fuel Consumption Monitoring data.
3.4 Service Functions (31+ Reset Functions)
The tool offers a wide range of service functions to help vehicles return to functional status after repair or replacement. Available tests vary by vehicle manufacturer, year, and model.
To perform a reset operation, follow these steps:
- Select Service Function
- Choose the desired service function
- Select the desired vehicle brand
- Select the reset mode (available modes vary by vehicle)
- Follow the on-screen instructions to proceed
Some key service functions include:
- Oil Reset Service: Resets the engine oil life system after oil change.
- Electronic Parking Brake Reset: Resets the brake pad after replacement.
- Steering Angle Calibration: Resets the steering angle after sensor or mechanical part replacement.
- ABS Bleeding: Performs bi-directional tests for the Anti-lock Braking System.
- Gear Learning: Performs tooth learning for the car to turn off the MIL.
- IMMO Service: Performs anti-theft key matching.
- Injector Coding: Writes or rewrites injector codes to the ECU.
- Battery Maintenance System Reset: Resets the vehicle battery monitoring unit.
- Diesel Particulate Filter (DPF) Regeneration: Clears PM from the DPF filter.
- Electronic Throttle Position Reset: Makes initial settings to throttle actuators.
- Gearbox Matching: Completes gearbox self-learning.
- AFS (Adaptive Front-lighting System) Reset: Initializes the adaptive headlamp system.
- Sunroof Initialization: Sets sunroof lock off, closed when it rains, sliding/tilting sunroof memory function, etc.
- Suspension Calibration: Adjusts the height of the body.
- EGR Adaption: Used to learn the EGR valve after cleaning or replacement.
- Seats Calibration: Applied to match seats with memory function.
- Tyre Reset: Sets size parameters of modified or replaced tires.
- Coolant Bleed: Activates the electronic water pump before venting the cooling system.
- AdBlue Reset (Diesel Engine Exhaust Gas Filter): Required after AdBlue replacement or refill.
- NOx Sensor Reset: Resets the catalytic converter learned value.
- AC System Initialization: Performed when the vehicle AC ECU or actuator is replaced.
- High Voltage Battery Detection: Used for high voltage battery diagnosis.
- Windows Calibration: Performs door window matching.
- Language Change: Changes system language of vehicle center console.
- AF Reset: Applied to set or learn air/fuel rate parameters.
- Transport Mode: Deactivates transport mode to recover normal vehicle functions.
- Stop/Start Reset: Opens or closes the automatic Start/Stop function via ECU settings.
- Intelligent Cruise Control System Reset: Matches the intelligent cruise control module after replacement or repair.
- Engine Power Balance Monitoring: Monitors crankshaft acceleration to determine relative power of each cylinder.
- Gas Particulate Filter (GPF) Regeneration: Performs GPF replacement or regeneration.
- Motor Angle Calibration: Performs motor angle calibration.
3.5 ECU Coding Function
The LAUNCH Creader Elite V3.0 supports online and offline ECU Coding functions to customize your car and make your work easier.
- Component Matching: Write adaptive data to match various on-board modules after replacement.
- Retrofit and Modification: Recode replacement parts to the car, perform transmission quick relearn, program VIN into replacement PCM.
- Personalization: Adapt codes to achieve personalized settings and improve vehicle comfort.
- Disable Annoying Functions: Such as locking seat-belt warning sounds, injector buzz sounds, daytime running light, auto start/stop, etc.
- Unlock Hidden Functions: Such as activate mirrors folding function, remove change speed limit, remote window control unlocking, adjust ambient lighting brightness, etc.
- Customize Car OE-Settings: Such as retrofit head-lamp, change tire size, retrofit battery with different type, customize dash kits, etc.
3.6 Battery Registration
The tool supports battery registration for both same and different type battery replacements.
Steps for Battery Registration:
- Replace and install a new battery.
- Switch on the ignition.
- Enter the 12-digit battery code.
- Complete the registration.
Registration Flow:
- For the Same Type & Capacity: Diagnostic > Car Brand > Car System > Special Function
- For the Different Type & Capacity: Diagnostic > Car Brand > Coding > Retrofit
4. Maintenance
4.1 Software Update
This function allows you to update the diagnostic software. All software is updated periodically. It is recommended to update and install the latest software version for the best service, functions, and experience.
- Use and update of the pre-installed diagnostic software is free of charge forever.
- The software subscribed in Mall can be free to use and update for one year. After it expires, you need to go to Mall to subscribe to the target software again.
Update Procedure:
- Tap Software Update on the main menu to enter the update center.
- Select the target software, and tap Update to start downloading. It may take several minutes to finish.
- Once downloading is finished, the software packages will be installed automatically.
Note: Software upgrades require a stable network connection.
4.2 Firmware Fix
Use this module to upgrade and fix diagnostic firmware. During fixing, do not cut power or switch to other interfaces.
4.3 Clean Up
This option allows you to clear some cache files and free up storage space on the device.
5. Troubleshooting
5.1 Diagnostic Trouble Code (DTC) Library
This option allows you to retrieve detailed descriptions of specific DTCs from the DTC database. Swipe upwards/downwards to alter the value, then press OK button, the screen will display the definition of the DTC.
5.2 General Troubleshooting Tips
- If you plan to take the vehicle to a Service Center for repair, DO NOT erase the codes from the vehicle's computer. If data is erased, valuable information that might help the technician troubleshoot the problem will also be erased.
- Clearing DTCs does not solve the underlying problems that triggered the codes. If appropriate repairs are not made to fix the problems, the codes will reappear, triggering the check engine light as soon as the problems causing the DTCs manifest themselves.
- If the tool fails to access VIN information automatically, you can manually input the VIN.
- For vehicles manufactured in 2020 or later, especially GM models, an additional CAN FD adapter may be required for full diagnostic functions. If you encounter connection issues, verify if your car uses the CAN FD protocol.
6. Specifications
| Feature | Specification |
|---|---|
| Screen | 4-inch touch screen, 480x800 pixels |
| CPU | 4-core 1.5GHz processor |
| RAM | 2GB |
| Storage | 64GB |
| OBDII Input Voltage Range | 9~18V |
| Charging | DC 5V 1.5A charging cable or via diagnostic cable |
| Operating Temperature | 0°C to 50°C (32°F to 122°F) |
| Storage Temperature | -20°C to 70°C (-4°F to 158°F) |
| Communication Interface | OBD-II |
| Software Update | Lifetime Free Update |
| Wireless Connectivity | Wi-Fi (2.4 GHz, 5 GHz) for updates and network functions. (Note: 'Wireless Support: No' likely refers to cellular/mobile data.) |
| Certification | CE |
| Origin | Mainland China |
| Material | Plastics |
| Package Dimensions (approx.) | 20cm (L) x 20cm (W) x 5cm (H) |
| Package Weight (approx.) | 0.7kg |
7. Warranty and Support
7.1 Warranty Information
This warranty is expressly limited to persons who purchase LAUNCH products for purposes of resale or use in the ordinary course of the buyer's business.
LAUNCH electronic product is warranted against defects in materials and workmanship for one year (12 months) from the date of delivery to the user.
This warranty does not cover any part that has been abused, altered, used for a purpose other than for which it was intended, or used in a manner inconsistent with instructions regarding use. The exclusive remedy for any automotive meter found to be defective is repair or replacement, and LAUNCH shall not be liable for any consequential or incidental damages.
Final determination of defects shall be made by LAUNCH in accordance with procedures established by LAUNCH. No agent, employee, or representative of LAUNCH has any authority to bind LAUNCH to any affirmation, representation, or warranty concerning LAUNCH automotive meters, except as stated herein.
7.2 Customer Service
If you have any questions on the operation of the unit, contact the seller, or contact LAUNCH TECH Service Center:
- Website: https://en.cnlaunch.com
- Phone: +86 755 8455 7891
- Email: overseas.service@cnlaunch.com
To resolve your problems quickly and efficiently, clearly indicate the Serial Number of your product when giving issue feedback.
7.3 Online Service
In the tool's 'More' module, you can contact our service staff for immediate technical support online.
7.4 User Manual (PDF Reference)
A detailed operation manual is integrated into the tool for quick reference. For a comprehensive PDF version, please refer to the official documentation available at LAUNCH Creader Elite V3.0 User Manual (PDF).
8. User Tips
- VIN Compatibility: For newer GM vehicles (2020+), always check if your car uses the CAN FD protocol. If so, an additional CAN FD adapter will be required for full diagnostic functions. You can send your vehicle's VIN to customer service for verification before purchasing an adapter.
- Regular Updates: Keep your diagnostic software updated frequently via Wi-Fi to ensure you have the latest features, bug fixes, and vehicle compatibility.
- Diagnostic Reports: Utilize the 'Health Report' and 'Live Data Stream Record & Playback' features to thoroughly document vehicle conditions before and after repairs. These reports can be invaluable for troubleshooting and sharing information.
- Language Settings: The tool supports multiple languages. Ensure you set your preferred language in the settings for ease of use.