1. Product Overview
The ANDELI MIG-250ME LED is a versatile 3-in-1 multiprocess welder, designed for Flux MIG, Lift TIG, and Stick welding. Featuring IGBT inverter technology, it offers efficiency, reliability, and a real 120AMP output current. Its portable design and user-friendly interface make it suitable for various applications, from plants to construction sites.

2. Safety Precautions
Always prioritize safety when operating welding equipment. Failure to follow safety guidelines can result in serious injury or death.
- Electric Shock: Welding current can cause fatal electric shock. Ensure proper grounding and insulation. Do not touch live electrical parts.
- Fumes and Gases: Welding produces fumes and gases that can be hazardous to health. Work in a well-ventilated area or use local exhaust ventilation.
- Arc Rays: Arc rays can injure eyes and burn skin. Wear a welding helmet with appropriate shade lenses and protective clothing.
- Fire and Explosion: Welding sparks can cause fire or explosion. Keep flammable materials away from the welding area. Have a fire extinguisher readily available.
- Burns: Hot metal and sparks can cause burns. Wear protective gloves and clothing.
- Noise: High noise levels can damage hearing. Wear ear protection.
3. Setup Instructions
3.1 Unpacking and Inspection
Carefully unpack the welder and all accessories. Inspect for any damage that may have occurred during transit. If any damage is found, contact your supplier immediately.
3.2 Included Accessories
The standard package includes:
- 1 PC MIG Welder (MIG-250ME LED)
- 1 PC Electrode Holder
- 1 PC Ground Clamp
- 2 PC Flux Cored Wire (0.5kg each)
- 2 pcs Nozzles
- 5 pcs Contact Tips
- 1 pc Hammer
- 1 3m MIG Gun

3.3 Power Connection
Connect the welder to a 220V AC power supply (50/60Hz). Ensure the power switch on the rear of the unit is in the 'OFF' position before connecting. The welder is designed for a rated input voltage of AC220V ±15%.

3.4 Welding Cable Installation
Properly install the welding cables for your chosen welding process (MIG, Lift TIG, or Stick). Refer to the diagram below for correct jack installations.
- MIG Jack Installation: Connect the MIG gun to the designated MIG jack.
- AW Jack Installation: Connect the ground clamp to the AW jack.
- TIG Jack Installation: Connect the TIG torch to the TIG jack.

3.5 Wire Feeding (for MIG)
The welder supports 1KG welding wire spools. Ensure the wire is correctly threaded through the wire feeder mechanism for smooth operation.

4. Operating Instructions
4.1 Control Panel Overview
The MIG-250ME LED features a digital display screen and an MCU intelligent precision chip for easier use. The control panel allows for adjustment of welding parameters.

4.2 Welding Modes
This welder supports three primary welding processes:
- Flux MIG: Gasless MIG welding, ideal for outdoor use or when gas cylinders are impractical.
- Lift TIG: For precise welding of thinner materials, requiring a TIG torch (not included in standard package).
- Stick (MMA): Manual Metal Arc welding, suitable for various metals and conditions.

4.3 Synergic Adjustment
The welder features a synergic design where voltage and wire feed speed are automatically matched. The current is also automatically adjusted based on the plate thickness, making it suitable for beginners.

4.4 Manual Mode (Pro Type)
For experienced users, the 'Pro Type' mode allows fine adjustment of wire feeder speed, welding current, and voltage. To activate manual mode, long-press the designated button for approximately 5 seconds.

4.5 Welding Thickness
The welder is designed for welding materials with a thickness range of 1-4mm. The synergic system can assist in setting parameters for common thicknesses like 0.5mm and 0.8mm.
5. Maintenance
Regular maintenance ensures the longevity and optimal performance of your welder.
- Cleaning: Periodically clean the exterior of the machine and ensure the cooling fan and vents are free from dust and debris. Use compressed air to clear internal dust if necessary, ensuring the machine is unplugged.
- Torch Maintenance: The split torch design allows for easy repair and replacement. Regularly check the MIG gun for wear on the nozzle, contact tips, and liner. Replace worn parts to ensure smooth wire feeding and consistent arc.
- Cable Inspection: Inspect all welding cables, electrode holders, and ground clamps for damage, cuts, or loose connections before each use. Replace any damaged components.
- Storage: Store the welder in a dry, clean environment, away from excessive dust, moisture, and corrosive materials.
6. Troubleshooting
This section provides general troubleshooting tips. For specific issues not covered here, please contact customer support.
- No Power: Check the power cable connection, the ON/OFF switch, and the circuit breaker. Ensure the input voltage is 220V.
- No Arc: Verify all welding cable connections (electrode holder, ground clamp, MIG gun). Check if the welding mode is correctly selected and parameters are set. Ensure the workpiece is clean and free of rust or paint.
- Poor Weld Quality: Adjust welding current/voltage, wire feed speed (for MIG), and ensure proper technique. Check for worn contact tips or nozzles in MIG welding.
- Overheating: If the machine stops due to overheating, allow it to cool down. Ensure adequate ventilation around the machine and that the cooling fan is operating correctly.
7. Specifications
| Attribute | Value |
|---|---|
| Brand Name | ANDELI |
| Model | MIG-250ME LED |
| Origin | Mainland China (Zhejiang) |
| Material / Metal Processed | Stainless Steel |
| Rated Input Voltage (V) | AC220±15%, 50/60Hz |
| Rated Input Current (A) | MIG: 18.7A / MMA: 23.2A |
| Output Current (A) | MIG: 40-120A / MMA: 20-120A |
| No-load Voltage (V) | 60V |
| Rated Cycle (%) | 60 |
| Efficiency (%) | 85 |
| Power Factor (cosφ) | 0.73 |
| Protection Class | IP21S |
| Insulation Class | F |
| Welding Thickness | 1-4mm |
| Wire Melting Type | Globular Transfer |
| Max. Load Power Capacity | 5.9 |
| Rated Output Voltage | 17.9 V |
| Welding Current/Voltage Range | 20-120 |
| Wire Feeding Speed | 12 |
| Dimensions | 370*155*290mm |
| Weight (kg) | 5 |
| Engine Power | electric (AC) |
| MIG Solid Wire Diameter (mm) | 0.8 mm, 1.0 mm |
| Key Selling Points | PORTABLE |
8. User Tips
While specific user reviews or Q&A were not provided, here are some general tips for optimizing your welding experience with the ANDELI MIG-250ME LED:
- Practice Makes Perfect: If you are new to welding, start with scrap pieces of metal to get a feel for the machine and different welding techniques.
- Cleanliness is Key: Always ensure your workpiece is clean, free of rust, paint, or oil. Contaminants can lead to poor weld quality and porosity.
- Proper Wire Stick-Out: For MIG welding, maintain a consistent wire stick-out (the length of wire extending from the contact tip) for stable arc and good penetration.
- Ventilation: Always work in a well-ventilated area to disperse welding fumes.
- Check Consumables: Regularly inspect and replace worn contact tips, nozzles, and electrode holders to ensure optimal performance and safety.
9. Warranty and Support
9.1 Warranty Information
The ANDELI MIG-250ME LED Welder comes with a 1 Year Warranty from the date of purchase. This warranty covers manufacturing defects and malfunctions under normal use. Please retain your proof of purchase for warranty claims.
9.2 Customer Support
For technical assistance, warranty claims, or any questions regarding your product, please contact the seller or manufacturer directly. Refer to your purchase documentation for contact details.