1. Safety Information
Always prioritize safety when operating welding and cutting equipment. Failure to follow safety precautions can result in serious injury or death.
- Wear appropriate Personal Protective Equipment (PPE) including welding helmet, gloves, protective clothing, and safety shoes.
- Ensure adequate ventilation to avoid inhaling fumes.
- Keep a fire extinguisher nearby.
- Do not operate the machine in wet conditions or near flammable materials.
- Ensure the workpiece is properly grounded.
- Disconnect power before performing any maintenance or changing accessories.
2. Product Overview
The ANDELI MCT-520DPL PRO is a versatile 5-in-1 multi-function welding machine capable of MIG/MAG (Gas/Gasless), Plasma Cutting (CUT), Lift TIG, MMA (Stick) welding, and Cold welding. It also features MIG Pulse for aluminum welding.
2.1 Key Features
- Multi-process capabilities: MIG/MAG, CUT, TIG, Cold, MMA, MIG Pulse for Aluminum.
- Precise stepless adjustment with digital display.
- Advanced IGBT inverter technology for stable performance.
- Suitable for welding aluminum, thin steel, iron, copper, mold repair, carbon steel, stainless steel.
- Compact design with a net weight of 14kg.

Figure 2: Welder dimensions (489mm x 210mm x 327mm) and weight (14kg).
3. Setup and Installation
3.1 Unpacking and Inspection
Upon receiving your welder, carefully unpack all components and inspect for any shipping damage. The standard packing list includes:
- MIG Torch (1 pc)
- TIG Torch (1 pc)
- MMA Torch (1 pc)
- CUT Torch (1 pc)
3.2 Power Connection
Connect the machine to a stable AC 220V-240V, 50/60Hz power supply. Ensure the power outlet is properly grounded and capable of handling the machine's maximum load power capacity of 9.5KW.
3.3 Torch and Ground Clamp Installation
Refer to the diagram below for proper connection of the various torches and the ground clamp for each welding/cutting mode.

Figure 3: Welding Torch Installation Diagram
- MIG/MAG: Connect the MIG torch and ground clamp as shown.
- Flux MIG: Connect the Flux MIG torch and ground clamp as shown.
- MMA: Connect the electrode holder (MMA torch) and ground clamp as shown.
- TIG: Connect the TIG torch and ground clamp as shown.
- Cold: Connect the Cold welding torch and ground clamp as shown.
- CUT: Connect the Plasma CUT torch and ground clamp as shown.
3.4 Wire Feeder Installation (for MIG/MAG/Flux MIG)
Open the side panel of the welder to access the wire feeder mechanism. Install the welding wire spool and thread the wire through the feeder rollers. Ensure the wire tension is correctly adjusted.

Figure 4: Wire Feeder Mechanism
The machine supports various wire sizes: 0.6mm, 0.8mm, 0.9mm, and 1.0mm. Select the appropriate wire size on the control panel.
3.5 Gas Connection (for MIG/TIG)
For MIG welding with gas, connect your CO2 or mixed gas cylinder to the gas inlet on the rear of the machine. For TIG welding, connect the appropriate shielding gas (e.g., Argon) to the TIG torch gas inlet. Ensure all gas connections are secure and leak-free.
4. Operating Instructions
4.1 Control Panel Overview
The front panel provides intuitive controls and a digital display for precise parameter adjustment.

Figure 5: Control Panel Introduction
- Wire Check / Gas Check / Storage Channel (0-9): Functions for checking wire feed, gas flow, and saving/recalling welding parameters.
- Welding Mode Selection: Select between MIG, CUT, TIG, Cold, MMA, and Pulse TIG welding.
- Gas Type Selection: Choose CO2, MIX (Ar+CO2 Mixed), Flux (Flux Wire Welding), or VRD (Voltage Reduction Device).
- Wire Size Selection: Select wire diameter (0.6mm, 0.8mm, 0.9mm, 1.0mm, or SP for separate current/voltage adjustment).
- Operating Mode: Select 2T (Manual Mode) or 4T (Semi-automatic Mode).
4.2 Selecting Welding Mode and Parameters
Turn on the machine. Use the control panel to select your desired welding or cutting mode and adjust parameters according to the material and thickness.
- MIG Function: Capable of welding 0.8-10mm carbon steel. For gasless welding, use flux-cored wire. For gas welding, use ordinary carbon steel wire with CO2 or mixed gas.
- TIG Function: Suitable for welding 0.8-8mm stainless steel and carbon steel. Note: The TIG function of this machine cannot weld aluminum.
- Cold Function: TIG supports cold welding for thin plates of 0.4-3mm stainless steel. This function minimizes distortion and discoloration.
- CUT Function: Contact plasma cutting for quickly cutting steel plates up to 8mm, with a maximum cutting thickness of 12mm.
- MMA Function: Suitable for continuous welding with 2.0-3.2mm electrodes.
- Aluminum Welding: MIG supports pulse function for welding 1-5mm aluminum plate in MIG mode.

Figure 6: MIG Welding in progress

Figure 7: TIG Welding in progress

Figure 8: Cold Welding in progress

Figure 9: Plasma Cutting in progress

Figure 10: MMA Welding in progress

Figure 11: Aluminum Welding in progress
4.3 Product Demonstration Video
Watch this video for a visual demonstration of the ANDELI MCT-520DPL PRO welder's features and operation.
Video 1: Overview of the ANDELI MCT-520DPL PRO Multi-Function Welder.
5. Maintenance
Regular maintenance ensures the longevity and optimal performance of your welding machine.
- Cleaning: Keep the machine's exterior and ventilation openings clean and free of dust and debris. Use compressed air to gently blow out internal dust periodically.
- Cable and Connection Inspection: Regularly check all welding cables, torches, and ground clamps for wear, cuts, or loose connections. Replace damaged components immediately.
- Wire Feeder Maintenance: Clean the wire feeder rollers and guide tubes to prevent wire feeding issues. Ensure the wire spool brake is properly adjusted.
- Gas System Check: Verify that gas hoses are not kinked or leaking. Check gas regulators for proper function.
- Storage: Store the machine in a dry, clean environment when not in use.
6. Troubleshooting
If you encounter issues with your welder, refer to the following common troubleshooting steps:
- No Power:
- Check if the power cord is securely plugged into a functional outlet.
- Verify the main power switch on the machine is in the 'ON' position.
- Check the circuit breaker or fuse in your electrical panel. - Poor Weld Quality:
- Ensure welding parameters (current, voltage, wire speed) are correctly set for the material and thickness.
- Check for proper gas flow (if applicable) and ensure the correct shielding gas is used.
- Clean the workpiece thoroughly; remove rust, paint, or oil.
- Inspect the welding wire/electrode for quality and proper size. - Wire Feeding Issues (MIG):
- Check if the wire spool is installed correctly and not tangled.
- Ensure the wire feeder rollers are clean and the tension is appropriate.
- Inspect the MIG torch liner for blockages or wear. - Machine Overheating:
- Ensure the machine's ventilation openings are not blocked.
- Allow the machine to cool down; the thermal overload protection will reset automatically.
- Reduce the duty cycle or welding current if operating continuously at high settings. - No Arc:
- Check that the ground clamp is securely attached to the workpiece and has good electrical contact.
- For TIG, ensure the tungsten electrode is properly sharpened and extended.
- For MMA, ensure the electrode is dry and suitable for the application.
If the problem persists after following these steps, please contact customer support.
7. Specifications
Detailed technical specifications for the ANDELI MCT-520DPL PRO Multi-Function Welder.
| Attribute | Value |
|---|---|
| Brand Name | ANDELI |
| Model | MCT-520DPL PRO |
| Origin | Mainland China |
| Rated Input Voltage | AC 220V-240V |
| Frequency | 50/60Hz |
| Max. Load Power Capacity | 9.5KW |
| Efficiency | 80%-85% |
| No-Load Voltage | 62V (TIG), 268V (CUT) |
| Output Polarity | DC TIG |
| Rated Output Current | 200A |
| Rated Welding Current Range | MIG: 50-200A, TIG: 10-200A, MMA: 10-200A, CUT: 20-50A |
| Rated Cycle @40°C (TIG) | 60% |
| Rated Output Voltage (TIG) | 70V |
| Pulse Frequency | 50/60Hz (MIG), 0.5-100Hz (TIG) |
| Welding Thickness | MIG: 0.8-10mm, TIG: 0.8-8mm, MMA: 1.5-10mm, CUT: 1-12mm, Cold: 0.4-3mm |
| Material / Metal Processed | Carbon steel, Stainless Steel, Aluminium alloy, Iron, Copper |
| Protection Class | IP21S |
| Insulation Class | H |
| Cooling | Fan |
| Weight (KG) | 14KG |
| Dimensions (MM) | 489 x 210 x 327 |
| Feature | Integrated Digital Display |
| Key Selling Points | High Productivity |
| Applicable Industries | Building Material Shops, Machinery Repair Shops, Manufacturing Plant, Construction works, Other |
Note: Specifications are subject to change without prior notice.
8. Warranty and Support
8.1 Warranty Information
This ANDELI MCT-520DPL PRO Multi-Function Welder comes with a 1-Year Warranty from the date of purchase. The warranty covers manufacturing defects and malfunctions under normal use. It does not cover damage caused by misuse, unauthorized modifications, or improper maintenance.
8.2 Customer Support
For technical assistance, warranty claims, or any questions regarding the operation or maintenance of your welder, please contact the seller or manufacturer's customer service. Keep your purchase receipt and product serial number handy when contacting support.
9. User Tips
Here are some general tips to enhance your welding experience and ensure optimal results:
- Practice Makes Perfect: Before working on critical projects, practice on scrap pieces of the same material and thickness to fine-tune your settings and technique.
- Cleanliness is Key: Always ensure your workpiece is clean and free of rust, paint, oil, or other contaminants. A clean surface leads to stronger, higher-quality welds.
- Match Parameters: Refer to the specification table and your material's requirements to select the correct current, voltage, wire speed, and gas flow for each welding process.
- Proper Grounding: A solid ground connection is crucial for consistent arc stability and safety. Ensure the ground clamp has direct contact with bare metal on the workpiece.
- Ventilation: Always work in a well-ventilated area to disperse welding fumes. If natural ventilation is insufficient, use fume extractors or respirators.
