Introduction
The DOMRAEM WLED Digital LED Controller series (ESP8266/ESP32 USB-C) offers advanced control for addressable LED strips. Utilizing open-source WLED firmware and a companion app, these controllers enable users to create custom lighting effects with over 16 million colors. Compatible with both iOS and Android devices, they support a wide range of LED strip types and offer features like music synchronization, voice control, and DIY programming.
Safety Information
- 16A Replaceable Fuse: Provides overload protection for enhanced safety.
- Reverse Polarity Protection: Prevents damage to the device from incorrect wiring.
Important: After any reset or OTA update, you must configure GPIO12. If LEDs stay off: Check GPIO12 config. If abnormal: reconfigure & reboot. If normal: inspect power supply circuit.
Product Overview
Model Differences
- DOM-WLE-S: ESP8266 chip, basic model, cost-effective.
- DOM-WLE-A: ESP32 chip, no microphone, no download port, pro-grade performance.
- DOM-WLE-AM: ESP32 chip, with microphone, no download port, music-reactive lighting.
- DOM-WLE-ADM: ESP32 chip, with microphone, with download port, fully programmable.
- DOM-WLE-RC005 (WLED WiFi Remote): ESP-NOW High-Speed, 4 presets, 50m range. Note: This remote cannot be used alone and requires a WLED series controller.
Unified Features
- Wide Compatibility: Supports WS2811, WS2812B, SK6812, and other DIMMER/RGB/RGBW/RGBCCT LED strips.
- Powerful Performance: 5-24V wide voltage input, 12A max per channel (16A total output).
- Dual-Purpose USB-C: Provides 5V/5A power supply and serves as a firmware update port.
- Smart Control: Over 100 lighting effects, segment control, voice control (Alexa/Google).
- Energy Efficient: Approximately 0.5W standby power consumption.
- DIY Friendly: Custom programming (ADM model), music sync (AM/ADM models).
Key Advantages
- Quad-mode smart control: WiFi/voice/sound/app comprehensive management.
- 16A high-current capacity supports extended LED strip runs.
- Open-source architecture enables continuous evolution.
- Visual programming for stunning effects.
- Energy-efficient long-term operation.
- Developer ecosystem supports secondary development.
Product Highlights
- Industrial-grade circuit protection design.
- Professional open-source lighting control system.
- One-touch smart scene switching.
- Minimalist aesthetic exterior design.
Specifications
| Parameter | Value |
|---|---|
| Product Name | WLED LED Strip Light Controller |
| Model No. | DOM-WLE-S / DOM-WLE-A / DOM-WLE-AM / DOM-WLE-ADM / DOM-WLE-RC005 |
| Brand Name | SAGE LU MEI |
| Item Type | RGB controller |
| Features | Addressable/DIY programmable |
| Voltage | DC 5-24V |
| Power Source | DC |
| Wattage | 384W |
| Max. Load Power | 384W |
| Output Current/Channel | 12A Max |
| Total Output Current | 16A Max |
| IC Quantity | 800 Max |
| Material | ABS |
| Oscillation Frequency | 50-60HZ |
| Connection Mode | WIFI |
| Remote Distance | 30M (for remote) |
| Applicable Lights | Pixel LED Strip/Addressable LED Light |
| Controlled Method | WLED WIFI APP / WLED remote control |
| Operating Temperature | -20-45°C |
| Size | 109.5*46*17.5mm |
| Supported Strip Types | WS2811, WS2812, WS2812B, WS2813, WS2814, WS2805, SK6812, SM16703P, FL1903B, etc. |
| Certification | CE, ROHS |
| High-concerned chemical | None |
| Warranty | No specific warranty information provided. |
Product Comparison Table
Refer to the table below for a detailed comparison of the different controller models:
This table details the input voltage, chip types (ESP32 or ESP8266), output current, IC quantity, presence of microphone, UART download capability, working temperature, material, net weight, and gross weight for each model.
Supported LED Strip Types
The controller supports a wide range of addressable LED strip types, including:
Setup Instructions
Wiring
The group of 'D' for GPIO16 is the default output; use this group first. The pins are labeled V=VCC, D=DATA, G=GND. The other group of 'D' is GPIO2, which can be used after configuration on the WLED app.
Quick Connect Port Design
- Open the connector upwards.
- Press down after inserting the wire.
- Wiring is complete, and the product is ready for use.
Power Supply
The controller supports three power supply methods:
- 1. 5.5x2.1mm DC Socket
- 2. V+, V- power interface
- 3. USB-C power supply (5V/5A)
For USB-C power, ensure it provides 5V/5A.
App Download
To download the WLED app:
- For iOS devices: Search and download 'WLED' or 'WLED Native' from the App Store.
- For Android devices: Download from the official GitHub repository: https://github.com/Aircoooke/WLED-App/releases.
App Configuration Steps
Follow these steps to configure your WLED controller via the app:
- Power on the WLED controller.
- Open your phone settings and find the Wi-Fi network 'WLED-AP' and connect to it with the password 'wled1234'.
- Open a browser and navigate to
4.3.2.1to display the account. - Enter the password, then click 'save' at the top of the screen. Be sure to choose a 2.4GHz Wi-Fi network, otherwise it will not work.
- Connect your phone and WLED controller to the same Wi-Fi network.
- Open the WLED app.
- Enter 'blank space' to enter the WLED page.
- Enter the WLED page for configuration.
Firmware Update (UART Download)
For advanced users, firmware can be updated via UART:
- Open the controller case.
- Remove the jumper cap (used to connect the motherboard power).
- Insert the USB-C data cable to download.
- After downloading, reinstall the jumper cap.
Note: When using the USB-C port for programming, the jumper cap needs to be removed. After downloading, reinstall the jumper cap.
Operating Instructions
App Control
The WLED app provides comprehensive control over your LED strips, offering 16 million colors and over 100 dynamic effects. You can easily select colors, effects, and segments from the intuitive interface.
Remote Control (Optional)
If you have purchased the DOM-WLE-RC005 WLED WiFi Remote, you can use it to control your LED strips. The remote allows you to set four favorite modes and offers a control distance of up to 50 meters. Please note that the remote is sold separately and requires a WLED series controller to function.
Dynamic Modes
For ESP32 models with a built-in microphone (DOM-WLE-AM, DOM-WLE-ADM), the controller supports Music Dynamic Mode. This allows lighting effects to synchronize with music, offering features like Built-in Microphone, Music Rhythm Sync Mode, ESP32 Inside processing, Lighting Effects Based on Melody, and DIY/Macros.
Segment Control
The WLED app allows you to divide your LED strip into multiple segments and apply unique colors and effects to each segment independently.
Sync Effects
When connected to the same Wi-Fi network, the lighting effects of LED strips connected to multiple WLED controllers can be synchronized.
Button Functions
The controller features a reset button and optional push buttons for control:
- Reset Button: Pressing the reset button briefly will power cycle the controller. Holding it for more than 10 seconds will reset the device to factory settings and activate the WLED-AP hotspot. Use this function only in emergencies, as it requires re-configuration.
- Push Buttons (GPIO33/GPIO0 - if available):
- Button 0 (GPIO33): Short press for On/Off. Long press for 1 second to adjust color. Long press for 10 seconds to enter Wi-Fi AP mode.
- Button 1 (GPIO0): Short press to adjust mode. Double-tap to adjust color within the current mode. Long press to adjust brightness.
Alexa Integration
To connect your WLED controller with Amazon Alexa:
- Go to the control page of the WLED controller in the app, click on the 'Config' button (top right corner) to enter settings, then click on 'Sync Interfaces'.
- Scroll up to find 'Alexa Voice Assistant', check the box next to 'Emulate Alexa device', and then save.
- After successfully saving, power cycle the WLED controller (turn it off and on).
- Open the 'Amazon Alexa' app, click on the 'Devices' page (top right corner) on the '+' sign, and then click 'Add Device'.
- Scroll up and click on 'Other' to enter, select 'Wi-Fi', and then click 'Discover Devices' to search for lights.
Maintenance
To ensure the longevity and optimal performance of your WLED Digital LED Controller:
- Keep the controller in a dry environment. Avoid exposure to moisture or extreme temperatures.
- Clean the device gently with a dry cloth; do not use liquid cleaners or abrasive materials.
- Ensure proper ventilation around the controller to prevent overheating, especially during prolonged use with high current loads.
Troubleshooting
- LEDs do not light up: After any reset or OTA update, you must configure GPIO12. If LEDs remain off, check the GPIO12 configuration. If abnormal, reconfigure and reboot the controller. If normal, inspect the power supply circuit for proper connection and adequate power.
- Incorrect Firmware: Always select the firmware that matches your controller's chip model (ESP8266 or ESP32). Using incorrect firmware can damage the device.
- Controller Unresponsive / Factory Reset: If the controller becomes unresponsive, a factory reset can be performed by holding the reset button for more than 10 seconds. This will activate the WLED-AP hotspot, and the device will need to be re-configured.
- Wi-Fi Connection Issues: Ensure you are connecting to a 2.4GHz Wi-Fi network during initial setup, as 5GHz networks are not supported. Verify the Wi-Fi password is correct.
User Tips
- Home Assistant Integration: This controller is compatible with Home Assistant, allowing for advanced home automation and integration with other smart devices.
- Power Supply Sizing: Always ensure your power supply provides sufficient voltage (5-24V) and current for the total length and type of your LED strip. Inadequate power can lead to dimming or flickering.
- LED IC Quantity: The controller supports up to 800 ICs. When planning your LED strip installation, ensure the total number of ICs does not exceed this limit to maintain optimal performance.
- Remote Control: If using the DOM-WLE-RC005 remote, remember it must be paired with a compatible WLED controller and cannot function independently.
Warranty and Support
No specific warranty information is provided with this product. For technical support, firmware updates, and detailed manuals, please refer to the WLED open-source community resources or scan the QR code provided on the product packaging for manufacturer support.