1. Introduction
The ISDT PC-4860S Safe Parallel Board is an advanced accessory designed for efficient and safe parallel charging of LiPo, Gaoneng, and Tattu batteries. It supports 1-8S battery configurations and features XT60 connectors for robust power connections. Engineered with a focus on safety and performance, this board allows users to charge multiple batteries simultaneously, optimizing charging time while maintaining critical safety standards.

2. Important Safety Information
WARNING: Lipo batteries can be dangerous. Improper handling or charging can lead to fire, explosion, or severe injury. Always follow these safety guidelines:
- Always use a charger compatible with LiPo batteries and the parallel board.
- Never charge batteries unattended.
- Ensure all batteries connected in parallel have the same cell count (e.g., all 3S, all 4S).
- Ensure all batteries connected in parallel have similar voltages (within 0.1V per cell is recommended).
- Do not connect damaged or swollen batteries to the parallel board.
- Always connect the main power leads (XT60) before connecting the balance leads.
- Always disconnect the balance leads before disconnecting the main power leads.
- Place the charging setup on a non-flammable surface, away from combustible materials.
- Keep a fire extinguisher or sand nearby when charging LiPo batteries.
- Do not exceed the maximum input or output current ratings of the board or your charger.

3. Package Contents
Verify that all items are present in your package:
- 1x ISDT PC-4860S Safe Parallel Board
- 1x XT60 Power Line (150mm)
- 1x 6S Balance Line (150mm)

4. Specifications
| Feature | Specification |
|---|---|
| Model Number | PC-4860S |
| Max Input Current | 40A |
| Max Output Current | 30A/Port |
| Max Balance Current | 2A |
| Balance Cells Supported | 1-8S |
| Power Plug Type | XT60 |
| Dimensions (L*W*H) | 88mm * 58mm * 22mm |
| Weight | 205g |
| Material | Metal (Aluminum housing) |
| Fuses | 32pcs Fuse |
| Output Channels | 4 Channels |


5. Setup
Before connecting any batteries, ensure your charger is powered on and configured for LiPo parallel charging with the correct cell count (e.g., 4S for 4S batteries).
- Connect to Charger: Use the provided XT60 power line to connect the ISDT PC-4860S parallel board to your LiPo charger's main output port. Connect the balance cable from the parallel board to your charger's balance port.
- Prepare Batteries: Ensure all batteries you intend to charge in parallel have the same cell count (e.g., all 4S) and are at a similar voltage level (within 0.1V per cell).
- Connect Batteries: For each battery, first connect its main power lead (XT60) to one of the four XT60 ports on the parallel board. Then, connect the battery's balance lead to the corresponding balance port on the side of the parallel board.


6. Operating Instructions
Once all batteries are securely connected to the ISDT PC-4860S parallel board and the board is connected to your charger:
- Verify Charger Settings: Double-check that your charger is set to the correct battery type (LiPo), cell count (e.g., 4S if charging four 4S batteries), and charging current. The total charging current should be distributed among the connected batteries. For example, if charging four 1300mAh 4S batteries, you might set your charger to 4 x 1.3A = 5.2A for a 1C charge rate.
- Start Charging: Initiate the charging process on your LiPo charger. Monitor the charging progress and battery temperatures closely.
- Monitor: Pay attention to any unusual smells, smoke, or excessive heat from the batteries or the parallel board. If any abnormalities occur, immediately disconnect the power and balance leads from the batteries and the charger.
- Completion: Once charging is complete, the charger will typically indicate this. First, disconnect the balance leads from the batteries, then disconnect the main XT60 power leads. Finally, disconnect the parallel board from the charger.
7. Maintenance
- Cleaning: Keep the parallel board clean and free from dust and debris. Use a soft, dry cloth for cleaning. Do not use liquids or solvents.
- Inspection: Regularly inspect the XT60 connectors and balance ports for any signs of wear, corrosion, or damage. Ensure all connections are firm and secure.
- Storage: Store the parallel board in a cool, dry place away from direct sunlight and extreme temperatures.
- Fuse Check: The board features 32 individual fuses for protection. If a charging port stops working, it may indicate a blown fuse. Consult a qualified technician for fuse replacement if necessary.
8. Troubleshooting
- Charger Not Detecting Batteries: Ensure all XT60 and balance leads are securely connected to both the batteries and the parallel board, and the parallel board is correctly connected to the charger. Verify that the charger settings match the battery type and cell count.
- Uneven Cell Voltages: If individual cell voltages are significantly different after charging, ensure all batteries connected in parallel had similar starting voltages. If the issue persists, check the balance leads and ports for damage or poor connection.
- Overheating: If the parallel board or batteries become excessively hot during charging, immediately stop the process. This could indicate a short circuit, damaged battery, or incorrect charger settings. Review all connections and battery conditions.
- Charging Port Not Working: This may indicate a blown fuse for that specific port. Inspect the board for any visible damage or consult the manufacturer for support.
9. Warranty and Support
For warranty claims, technical support, or service inquiries regarding your ISDT PC-4860S Safe Parallel Board, please contact the seller or the official ISDT customer support channel. Keep your proof of purchase for warranty validation.