1. Introduction
The Yesper P2 JumpBooster is a heavy-duty, portable 12V/24V jump starter and power bank designed for emergency vehicle starting and charging electronic devices. With a peak current of 5000A and a battery capacity of 122500mAh, it is suitable for a wide range of vehicles including cars, pickups, RVs, semi-trucks, and excavators. This manual provides essential information for safe and effective use, maintenance, and troubleshooting.

2. What's in the Box

- Yesper P2 Jump Starter
- Charge Adapter
- User Guide (this manual)
- USB-A to USB-C Cable
3. Product Layout

- Battery Clamp: Connects to vehicle battery terminals.
- LED Flash Light: Provides illumination.
- Indicator: Displays battery status and operational modes.
- DC 29V/5A Input Port: For charging the jump starter.
- USB-C Input Port: For charging the jump starter.
- Warning Light: Indicates potential issues or safety warnings.
- 12V Button: Selects 12V jump-starting mode.
- 24V Button: Selects 24V jump-starting mode.
- 5V/1A Output Port (USB-A): For charging electronic devices.
- LED Switch: Controls the LED flash light.
- 5V/2.4A Output Port (USB-A): For charging electronic devices.
4. Specifications
| Feature | Specification |
|---|---|
| Brand | Yesper |
| Model Number | P2 (Monster Start P2) |
| Start Voltage | 12V/24V |
| Battery Type | LiFePO4 Battery |
| Battery Capacity | 122500mAh |
| Peak Current | 5000A |
| Input | DC 29V/5A, USB-C (PD65W) |
| Output | USB-A (5V/1A), USB-A (5V/2.1A), DC (12V/10A) |
| Total Output | 453Wh |
| Dimensions | 248 x 248 x 96 mm |
| Weight | 7 Kg (11.9 pounds) |
| Operating Temperature | -40℃ ~ +60℃ |
| Cycle Life | 3000x, 3000 Times |
| Charging Time | 4 Hours |
| Certification | CE, FCC, ROHS, MSDS, UN38.3 |
5. Safety Information
Always observe the following safety precautions when using the Yesper P2 JumpBooster:
- Read all instructions before use.
- Do not operate the device if it is damaged.
- Keep out of reach of children.
- Ensure proper ventilation during use.
- Do not short-circuit the battery clamps.
- Do not expose the device to extreme temperatures or moisture.
- The device features multiple protection mechanisms:

- Over Charge Protection
- Over Discharge Protection
- Over Voltage Protection
- Over Current Protection
- Over Temperature Protection
- Reverse Charge Protection
- AI Software Protection
- Reverse Polarity Protection
- Short Circuit Protection
- Low Self-Consumption
6. Setup and Charging
Before first use, fully charge the JumpBooster. It is recommended to recharge the device every 3-6 months to maintain battery health.
6.1 Charging the Jump Starter
Connect the provided charge adapter to the DC 29V/5A input port or use a USB-C PD65W charger with the USB-C input port. The indicator lights will show the charging progress. A full charge takes approximately 4 hours.

7. Operating Instructions
7.1 Jump Starting a Vehicle
Follow these steps to safely jump start your vehicle:
- Remove Negative Battery Cable: Disconnect the negative (-) battery cable from your vehicle's battery.
- Connect Red Clamp: Attach the red (+) clamp of the JumpBooster to the positive (+) terminal of your vehicle's battery.
- Connect Black Clamp: Attach the black (-) clamp of the JumpBooster to the negative (-) terminal of your vehicle's battery.
- Select Voltage: Long press the appropriate voltage button (12V or 24V) on the JumpBooster to match your vehicle's battery system. The indicator lights will confirm the selection.
- Start Vehicle: Attempt to start your vehicle. If it doesn't start immediately, wait a few minutes and try again.
- Disconnect: Once the vehicle starts, disconnect the black (-) clamp first, then the red (+) clamp, and finally reattach your vehicle's negative battery cable.
7.2 Using as a Power Bank
The JumpBooster can charge various electronic devices via its USB-A output ports (5V/1A and 5V/2.1A). Simply connect your device using a compatible USB cable.
7.3 LED Lighting Functions
The built-in LED flash light offers multiple modes for different situations:

- Stable: For general illumination.
- Strobe: For signaling or attracting attention.
- SOS: For emergency signaling.
Use the LED switch to cycle through the modes.
8. Maintenance
- Clean the device with a dry, soft cloth. Do not use harsh chemicals or abrasives.
- Store the JumpBooster in a cool, dry place away from direct sunlight and extreme temperatures.
- Recharge the device every 3-6 months to prevent deep discharge and prolong battery life.
- Inspect the clamps and cables for any damage before each use.
9. Troubleshooting
- Device does not turn on:
- Ensure the device is charged. If not, connect it to a power source using the provided adapter or USB-C cable.
- Vehicle does not start:
- Check that the clamps are securely connected to the correct battery terminals. Ensure the correct voltage (12V or 24V) is selected. The vehicle battery might be severely discharged or damaged, requiring professional assistance.
- Warning light is active:
- Refer to the safety information section (Section 5) for a list of protection mechanisms. The warning light indicates that one of these protections has been triggered (e.g., reverse polarity, short circuit). Disconnect the clamps, identify and resolve the issue, then reconnect.
10. User Tips
- For optimal performance, ensure the JumpBooster is fully charged before attempting to jump start a vehicle.
- Always connect the clamps firmly to ensure good contact with the battery terminals.
- In extremely cold weather, keep the JumpBooster indoors until just before use to maximize its efficiency.
11. Warranty and Support
For warranty information, technical support, or service inquiries, please contact the manufacturer or your point of purchase. Keep your purchase receipt as proof of purchase.