Introduction
This manual provides comprehensive instructions for the safe and efficient operation, assembly, and maintenance of your LASER TREE K1Max Plus Laser Engraver. Please read this manual thoroughly before initial use to ensure proper setup and to maximize the performance and longevity of your device.
Video: Overview of the LASER TREE K1Max Plus Laser Engraver in operation, demonstrating its cutting capabilities.
1. Safety Statement
Before using the laser engraving machine, please peruse this safety manual attentively to comprehend the operating protocols and potential hazards associated with the laser engraving machine.
- Sharp edges may cut your hands when assembling the stand, gloves are recommended.
- Laser beam has high energy and heat; direct contact with eyes or skin may cause serious injury. When the laser is working, always pay attention to the position and direction of laser beam movement.
- Children or teenagers are strictly prohibited from using the laser engraving machine alone.
- The laser engraver should be placed on a stable tabletop. Before use, please clean the work area to ensure that the surrounding environment is safe and free of debris, flammable and explosive items, etc., to prevent potential safety hazards.
- Before using the laser, carefully check the power connection of the laser engraver. Make sure that the power cord is intact and the plug is firmly connected to avoid accidents caused by power problems.
- When the laser is working, you must wear professional protective glasses to protect your eyes from laser damage. Protective glasses can block the laser light and avoid direct exposure to the eyes.
- When the laser is working, the engraving area should be paved with metal or non-combustible mats to prevent the laser from burning the workbench or causing fire and other safety hazards.
- When the laser is working, please do not leave the equipment during operation. Stay focused and pay close attention to the operation of your equipment, to prevent the engraving or cutting material from catching fire.
- When the laser is working, some materials produce smoke during laser cutting. Please keep the room well ventilated.
- Residue and debris can accumulate during the cutting and engraving process. Please clean up the work area promptly.
- Please ensure that a fire extinguisher is located near the laser engraving machine and that regular maintenance and inspections are conducted to promptly respond to any accidents that may occur.
2. Specification Parameters
The LASER TREE K1Max Plus is a versatile laser engraving and cutting machine designed for both hobbyists and professionals, featuring a large working area and adjustable laser power.
| Parameter | Value | Parameter | Value |
|---|---|---|---|
| Brand | LASERTREE | Support Software | LightBurn & LaserGRBL |
| Model | K1 MAX PLUS | Air Assistance | Yes |
| Engraving Area | 1000*1500 mm | Rotation Axis Output | Yes |
| Engraving Speed | 20000 mm/min | Offline Engraving | Yes |
| Wavelength | 450nm (±10nm) | Emergency Stop | Yes |
| Focus length | 40mm | Tilt Protection | Yes |
| Optical Power | 60W+ | Status Indicator | Yes |
| Input | DC24V 10A | Operating Temperature | 0-40°C |
| Certification | CE, FCC, RoHS, WEEE | Origin | Mainland China |

Image: Demonstrates the cutting capability of the 60W optical power output, showing cuts through 20mm Plywood, 30mm Black Acrylic, and 40mm Pine Wood.

Image: Illustration of the switchable power modes (20W, 40W, 60W) for the laser module, allowing free selection of light power.

Image: K60 Series cutting depth chart for three power options (20W, 40W, 60W) on various materials like Plywood, Pine Wood, MDF, and Acrylic, showing speed and cutting depth for a single pass at 100% power.
3. About Laser Engraving Machine
3.1 Laser Engraving Machine Components

Image: Highlights the quick assembly feature with a modular design and neat cable organization using drag chains for protection and smooth operation.

Image: Diagram of the K1 Max Plus Laser Engraving Machine, labeling key components such as Main Control Box, Front Frame, Rear Frame, Y-Axis Assembly, X-Axis Assembly, and Laser Module.
3.2 Laser Module

Image: Detailed diagram of the Laser Module, showing Input port, Air assistance port, Optical power indicator, Signal indicator, Fixed focus lever, Laser view window, Red cross line locating, Laser output aperture, Power indicator, Working temperature display, and Switch.
Laser Module Features:
- Power indicator: Red when power supply is connected.
- Signal indicator: Green when signal is received.
- Working temperature display: Shows real-time working temperature. An alarm sounds if temperature exceeds 55°C. Recommended operating temperature is below 55°C for stability.
- Switch:
- Function 1: Turns off buzzer alarm for over-temperature.
- Function 2: Switches optical power between 60W, 40W, and 20W. Long press for 5 seconds to enter switching mode, then short press to cycle.

Image: Illustrates the machine's tilt detection and protection system, which triggers an alarm if the machine is tilted during operation.
4. Packing List
Please verify that all components listed below are present in your package. If any items are missing or damaged, please contact customer support.
Main Components:
- X-Axis A x1
- X-Axis B x1
- Y-Axis A x2
- Y-Axis B x2
- Front Frame x2
- Rear Frame x2
- Linear Guide Rail A x1
- Linear Guide Rail B x1
- Coupling Shaft A x1
- Coupling Shaft B x1
- X-axis Drag Chain Guide x2
- Y-axis Drag Chain Guide x2
- X-axis Transmission Unit x1
- X-axis Motor Mounting Plate x1
- Y-axis Motor Mounting Plate x1
- Y-axis Pulley Mounting Plate x1
- Y-axis Drag Chain Fixing Plate x1
- Y-Axis Drag Chain Carrier Link Plate x1
- Y-axis Drag Chain Support Foot x2
- X-axis Cable x1
- Y-axis Cable x1
- Distribution Box x1
- Main Control Box x1
- Support Foot x3
- Power Adapter x1
- AC Cable x1
- USB Cable x1
- 60W Laser Module x1
- Air Pump x1
- Protective Glasses x1
- Material Pack x1
Splicing Kit:
- Linear Splicing Connector A x10
- Linear Splicing Connector B x10
- Flat Screw M5*16 x41
Tool Kit:
- Cleaning Brush x1
- 8-10 Open Spanner x1
- 4.5 Open Spanner x1
- L-Allen wrench x1
- Cable Ties x3
- Timing Belt x2
- Sleeve Coupling x1
- TF Card x1
- Card Reader x1
- Spare Laser Protective Lens x2
- Air Pump Filter Sponge x2
Screws and Fasteners:
- Round Screw M4*18 x1 (Screw E)
- Round Screw M5*10 x4 (Screw C)
- Round Screw M5*16 x8 (Screw F)
- Round Screw M5*20 x21 (Screw A)
- Flat Screw M2.5*4 x2 (Screw B)
- Flat Screw M3*6 x7 (Screw I)
- Flat Screw M3*12 x20 (Screw H)
- Flat Screw M5*20 x1 (Screw G)
- Flat Screw M5*25 x1 (Screw G)
- Thin Flat Screws M4*6 x28 (Screw D)
- Limiting Column Sleeve 5*8*8 x1 (Screw G)
- Limiting Column Sleeve 5*8*12 x1 (Screw G)
- Fasten Screw M4*5 x5 (Screw G)
- T-Nut x5 (Screw G)
- Adjusting Screw M4*30 x2 (Screw G)
- Hexagonal Copper Column M3*13+3 x3 (Screw J)

Image: The K1 Max Plus laser engraver shown with its full set of accessories, including Power Adapter, AC Cable, Protective Glasses, Material Pack, and Air Pump.
5. Installation Guide
5.1 Assembly of Main Frame
- Assemble the front/rear frames and X/Y-axis frames using linear splicing connectors.

Image: Diagram illustrating the assembly of the main frame components, including X-Axis Beam, Front Frame, Rear Frame, and Y-Axis parts, using linear splice connectors and flat screws.
5.2 Assembly of X-axis
- Assembly of X-axis linear guide rail:
- Installation: Install linear guides A and B into the designated holes on the X-axis, and tighten the front and rear screws on the outermost side of each guide. Note: None of the screws should be fully tightened at this stage; they are only for temporary positioning.
- Adjust the Gap and Height: Focus on adjusting the gap and height at the junction between the rails A and B. Ensure a smooth transition and consistent surface level between the two, with no visible gap or misalignment. Once properly adjusted, securely tighten the two key screws in the center to lock the relative position in place.
- Test sliding and fixing: After completing the above steps, perform a manual sliding test to ensure smooth movement without any binding. If there is any binding, fine-tune the screws until it is smooth. Once the test passes, tighten all the fixing screws in sequence to complete the process.
- Assembly of X-axis transmission unit:
- Flatten the belt to avoid twisting; correctly insert the belt into the guide groove of the motor fixing plate, align the fixing plate with the left rear hole, and tighten the screws.
- Align the drive unit slider with the linear guide groove and secure.
- Align the mounting plate with the right rear hole of the X-axis and tighten the screws.
5.3 Assembly of Engraving Machine
- Push the X-axis into the Y-axis grooves on both sides. Use M5*20 screws to fix the front frame and rear frame.
- Make the timing belt face downward. Pass the timing belt through the X-axis pulley by hand or using the appropriate tool so that it fits snugly and ensures a smooth motion of the timing belt over the pulley. (Same operation for both left and right sides)
- Ensure a T-nut is inserted into the groove at each of the four corners of the Y-axis frame.
- Fix the drag chain support foot to the left Y-axis support angle and the control box, and lock the support angle to the engraving machine frame.
- Adjust the fastening timing belt:
- Fix the rear frame and timing belt: Use the M4x5 setscrew to secure the rear end of the timing belt to the rear frame.
- Position the X-axis: Push the X-axis backward to ensure that the X-axis is in close contact with the rear frame without any gap.
- Fix the front frame and timing belt: Pull the Y-axis timing belt forward to the correct tension and secure with the M4*5 set screws. Press the middle span of the timing pulley with your finger to make sure the belt is flexible. If the belt is too loose or too tight, it needs to be adjusted.
5.4 Assembly of Distribution Box
- Use M3*13+3 hexagonal copper column to secure the junction box driver to the Y-axis motor pulley.
- Assemble the distribution box housing and the Y-axis drag chain fixing plate.
- Connect the distribution box cables.
5.5 Assembly of X-axis and Y-axis Drag Chain and Cable
Install the Thin Flat Screws M4*6 in four locations. Each location needs 3 screws.
5.6 Connection Cable
Connect all necessary cables as per the diagrams provided in the PDF manual (page 22).

Image: Diagram showing the connection points for the laser cable, air tube, main cable, and electrostatic conductor cable.
6. Interface Description
6.1 Main Control Box Interface Description

Image: Diagram of the Main Control Box, detailing the various ports and their functions.
- Power input: Aviation 4P plug, voltage DC 24V, current 10A.
- Device main cable interface: PHB2.0-2*10PIN buckle terminal, connected to the distribution box.
- Air assistance output: DC5.5*2.1mm socket, output DC 24V.
- USB-PC interface: Port type USB-B, Connect with PC and burn program.
- Power switch: Self-locking switch, controls the current on and off of the whole machine, with red indicator light.
- TF card slot: Stores offline engraving files. Recommended TF card type is Class 10, 4~16G, Fat32 format. Supported offline engraving file format is .nc .gc.
- Emergency stop switch: Stops the device action and PWM signal output and disconnects the device from the PC.
Status Indicator:
| Indicator | Description |
|---|---|
| Red always on | No TF card is inserted and the PC is not connected to the engraving machine. |
| Red flashing | No TF card inserted. |
| Green always on | The TF card inserted with .gc.nc file. The PC is connected or not connected to the engraving machine. |
| Yellow always on | TF card inserted without .gc.nc file. The PC is not connected to the engraving machine. |
| Yellow stays on for 2s | TF card without .gc.nc file. |
| Blue always on | Engraving machine at work. |
Note: After successfully connecting to the computer, the connection status (green light is always on) will not change until the hardware is reset or the power is turned on again.
6.2 Distribution Box Port Description

Image: Diagram of the Distribution Box, showing ports for Rotary axis switching, Y-axis motor output, X-axis motor output, Laser module output, Device main cable, and Rotary axis output.
- Rotary axis switching: Y-axis motor and rotary axis motor control switching.
- Y-axis motor output and limit signal input.
- X-axis motor output and limit signal input.
- Laser module output interface: MR30 port (DC 24V, GND, PWM).
- Device main cable interface: Connect to the main control box.
- Rotary axis output: PH2.0-4PIN terminal, connected to the rotary table motor.
7. Software Connection Guide
The K1 MAX PLUS supports both LaserGRBL and LightBurn engraving software.
7.1 LaserGRBL
LaserGRBL download address: https://lasergrbl.com/download/
- Connect one end of the USB data cable to the engraving machine and the other end to the USB port of the computer with LaserGRBL software installed.
- Connect the power port of the engraving machine through the DC24V adapter and turn on the power switch.
- Open the LaserGRBL software on the computer, select the correct COM port and click connect. If the status bar displays "SimpleLaser 1.1h", the connection is successful.

Image: Screenshot of the LaserGRBL interface showing the COM port selection and connection button.
7.2 LightBurn
LightBurn download address: https://lightburnsoftware.com/pages/download-trial
- Connect one end of the USB data cable to the engraving machine and the other end to the USB port of the computer with LightBurn software installed.
- Connect the power port of the engraving machine through the DC24V adapter and turn on the power switch.
- Open the LightBurn software, select “Start Your Free Trial” or “Activate License".
- Create a new device, select "GRBL".
- Select USB connection.
- Set the engraving size to 1000*1500mm and modify the device name "K1 MAX PLUS".
- Set the origin position of the machine and turn off automatic reset on power-on. (If you need to automatically reset every time you turn on the computer, please tick step 2 of the attached diagram.)
- Complete software setup.
- Select the "K1 MAX PLUS" device and the correct COM port. When the status bar displays Ready, the device is successfully connected.

Image: Screenshots of LightBurn setup process, including license page, new device wizard for selecting GRBL, setting work area dimensions, and origin position.
8. Machine Test Guide
8.1 LaserGRBL Test
- Engraving machine reset test: Find the reset button on the default interface of LaserGRBL and click it. Under correct operation, the laser module should be moved to the side of the control box and stopped moving when it hits the limit column.
- Engraving machine movement test:
- Find the direction button on the default interface of LaserGRBL and set the moving distance and speed. (The recommended moving distance is 10mm.)
- Click in any direction. Under correct operation, the laser module should move in the direction shown by the arrow.
- Engraving machine laser module light test: Find the light button on the LaserGRBL default interface and press and hold it. Under correct operation, the laser module should emit blue light normally.

Image: Screenshots of the LaserGRBL interface showing the reset button, movement controls with distance/speed settings, and the light button for laser module test.
8.2 LightBurn Test
- Engraving machine reset test: Find "Home" in the lower right corner of LightBurn default interface and click on it. Under correct operation, the laser module should be moved to the side of the control box and stopped moving when it hits the limit column.
- Engraving machine movement test:
- Find "Move" in the lower right corner of LightBurn default interface and open it.
- Set the moving distance and speed. (The recommended moving distance is 50mm.)
- Click in any direction. Under correct operation, the laser module should move in the direction indicated by the arrow.
- Engraving machine laser module light test:
- Open the device settings, turn on the laser ignition option and set air assist to M7.
- Find "Move" in the lower right corner of the LightBurn default interface, set the optical power to 0.5% and click "Fire". Under correct operation, the laser module should emit blue light.

Image: Screenshots of the LightBurn interface showing the "Home" button for reset, the "Move" panel for movement tests with distance/speed settings, and the laser module light test controls (power and "Fire" button).
9. Laser Module Focus Guide
The K1 MAX PLUS laser module has a working focal length of 40mm.
Focusing for Cutting:
When cutting, you only need to make the focus locate a bit lower than the surface of materials. For example, if you want to cut 12mm material, the focus should be 6mm lower than the material surface. Please adjust the fixed focus lever to 6mm.
| Material thickness | < 5mm | 5mm | 8mm | 10mm | 12mm | 15mm | > 30mm |
|---|---|---|---|---|---|---|---|
| Fixed focus lever | 0mm | 2mm | 4mm | 5mm | 6mm | 7mm | 7mm |

Image: Diagram illustrating the fixed focus lever adjustment for cutting, showing how to set the focus below the material surface.
Focusing for Engraving:
When engraving, please ensure that the focus is located on the material surface. Just adjust the fixed focus lever to 0mm.
| Parameter | Fixed focus lever (mm) | Speed (mm/min) | Max Power | Line Interval | ||||
|---|---|---|---|---|---|---|---|---|
| Material | 20W | 40W | 60W | 20W | 40W | 60W | ||
| Basswood Plywood | 0 | 12000 | 15000 | 18000 | 50% | 45% | 30% | 0.05 |
| Pine Board | 0 | 10000 | 12000 | 15000 | 55% | 50% | 40% | 0.05 |
| Stainless Steel | 0 | 9000 | 10000 | 13000 | 60% | 70% | 80% | 0.01 |

Image: Diagram illustrating the fixed focus lever adjustment for engraving, showing how to set the focus on the material surface.
10. Maintenance
Lens Cleaning:
- When the laser module is used for a long time, you need to use an alcohol swab to wipe the laser protective lens to ensure the best cutting and engraving performance.
- Caution for lens cleaning:
- Before wiping the lens, make sure the power is turned off and the laser module is disconnected from the engraving machine.
- After wiping, allow the lenses to dry naturally for 3 to 5 minutes before use.
- When the laser module is not used for a long time, please ensure that the lens is not polluted by dust.

Image: Visual guide for cleaning the laser protective lens, showing examples of dust and fingerprints, and how to access the protective lens for cleaning or replacement.
For more information about maintenance, please contact us at lasertree@micost-optotech.com.
11. Troubleshooting
- Machine not powering on: Check power cable connection to the machine and power outlet. Ensure the power switch on the main control box is in the ON position.
- Laser module not moving: Perform the "Engraving machine reset test" and "Engraving machine movement test" as described in Section 8. If the module still doesn't move, check cable connections to the motors and main control box.
- Laser not firing or weak: Perform the "Laser module light test" as described in Section 8. Ensure the optical power is set correctly in your software (e.g., 0.5% for test fire in LightBurn). Check the laser protective lens for cleanliness (refer to Section 10).
- Software connection issues: Ensure the correct COM port is selected in LaserGRBL or LightBurn. Verify USB cable connection. Restart the software and the machine.
- Engraving/Cutting quality issues: Check laser focus (refer to Section 9). Ensure material parameters (speed, power, line interval) are appropriate for your material and desired outcome (refer to tables in Section 9). Clean the laser lens if necessary.
- Machine making unusual noises: Check for any obstructions in the movement path of the X and Y axes. Ensure timing belts are properly tensioned (not too loose or too tight).
- Over-temperature alarm: If the laser module temperature exceeds 55°C, the buzzer will sound. Press the switch on the laser module to turn off the alarm. Allow the module to cool down. Ensure adequate ventilation in your workspace.
12. User Tips
- Assembly Guidance: While a dedicated step-by-step video for assembly is not provided, this manual offers detailed textual instructions accompanied by clear diagrams for each assembly step. Pay close attention to these visuals and descriptions for a smooth setup.
- Software Familiarization: Both LaserGRBL and LightBurn are supported. If you are new to laser engraving software, consider exploring online tutorials specific to these programs in conjunction with this manual's connection and test guides.
- Material Testing: Always perform small test engravings or cuts on scrap material before starting a large project. This helps in fine-tuning speed, power, and focus settings for optimal results on your specific material.
- Workspace Ventilation: Laser engraving and cutting can produce smoke and fumes. Always ensure your workspace is well-ventilated, as mentioned in the safety guidelines.
- Regular Cleaning: Keep the laser protective lens clean and free of dust and debris to maintain consistent engraving and cutting quality.
13. Warranty & Support
LASER TREE products typically come with a 1-year warranty from the date of purchase. For specific warranty details, claims, or technical support, please refer to the following:
- Warranty Period: 1 year from purchase date.
- Support Contact: For maintenance inquiries and technical assistance, please contact lasertree@micost-optotech.com.
- Item Guides & Documents: A PDF version of the user manual is available for download. Download User Manual (PDF)
All emails will be answered within 24 hours.