1. Safety Warnings and Regulations
1.1 FCC Regulatory Conformance
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. Verification of harmful interference by this equipment to radio or television reception can be determined by turning it off and then on. The user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference.
WARNING! MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW.
1.2 RF Exposure Compliance and Control
The radio complies with the following RF energy exposure standards and guidelines:
- United States Federal Communications Commission, Code of Federal Regulations; 47 CFR § 1.1307, 1.1310 and 2.1093
- American National Standards Institute (ANSI) / Institute of Electrical and Electronic Engineers (IEEE) C95.1:2005; Canada RSS102 Issue 5 March 2015
- Institute of Electrical and Electronic Engineers (IEEE) C95.1:2005 Edition
Guidelines and Operating Instructions: To control your exposure and ensure compliance with the occupational/controlled environmental exposure limits, always adhere to the following procedures:
- Do not remove the RF Exposure Label from the device.
- User awareness instructions should accompany device when transferred to other users.
- Do not use this device if the operational requirements described herein are not met.
- Transmit no more than the rated duty factor of 50% of the time. To transmit (talk), press the Push-to-Talk (PTT) key. To receive calls, release the [PTT] key. Transmitting 50% of the time, or less, is important because the radio generates measurable RF energy only when transmitting (in terms of measuring for standards compliance).
- Keep the radio unit at least 2.5cm away from the face. Keeping the radio at the proper distance is important as RF exposure decreases with distance from the antenna. The antenna should be kept away from the face and eyes.
- When worn on the body, always place the radio in an approved holder, holster, case, or body harness or by use of the correct clip for this product. Use of non-approved accessories may result in exposure levels which exceed the FCC's occupational/controlled environmental RF exposure limits.
- Use of non-approved antennas, batteries, and accessories causes the radio to exceed the FCC RF exposure guidelines.
- Contact your local dealer for the product's optional accessories.
1.3 Precautions for Portable Terminals
Operating Prohibitions: To protect you against any property loss, bodily injury or even death, be sure to observe the following safety instructions:
- Do not operate the product in a location containing fuels, chemicals, explosive atmospheres and other flammable or explosive materials. In such location, only an approved Ex-protection model is allowed for use, but any attempt to assemble or disassemble it is strictly prohibited.
- Do not operate the product near or in any blasting area.
- Do not operate the product near any medical or electronic equipment that is vulnerable to RF signals.
- Do not hold the product while driving.
- Do not operate the product in any area where use of wireless communication equipment is completely prohibited.
Important Tips: To help you make better use of the product, be sure to observe the following instructions:
- Do not use any unauthorized or damaged accessory.
- Keep the product at least 2.5 centimeters away from your body during transmission.
- Do not keep the product receiving at high volume for a long time.
- For vehicles with an air bag, do not place the product in the area over the air bag or in the air bag deployment area.
- Keep the product and its accessories out of reach of children and pets.
- Please operate the product within the specified temperature range.
- Continuous transmission for a long time may lead to heat accumulation within the product. In this case, please keep it at a proper location for cooling.
- Handle the product with care.
- Do not disassemble, modify or repair the product and its accessories without authorization.
1.4 Precautions for Batteries
Charging Prohibitions: To protect you against any property loss, bodily injury or even death, be sure to observe the following safety instructions:
- Do not charge or replace your battery in a location containing fuels, chemicals, explosive atmospheres and other flammable or explosive materials.
- Do not charge your battery that is wet. Please dry it with a soft and clean cloth prior to charge.
- Do not charge your battery suffering deformation, leakage and overheat.
- Do not charge your battery with an unauthorized charger.
- Do not charge your battery in a location where strong radiation is present.
- Overcharge shall always be prohibited for it may shorten the life of your battery.
Maintenance Instructions: To help your battery work normally or prolong its life, be sure to observe the following instructions:
- Accumulated dust on charging connector may affect normal charging. Please use a clean and dry cloth to wipe it on a regular basis.
- It is recommended to charge the battery under 5°C~40°C. Violation of the said limit may cause battery life reduction or even battery leakage.
- To charge a battery attached to the product, turn it off to ensure a full charge.
- Do not remove the battery or unplug the power cord during charging to ensure a smooth charging process.
- Do not dispose of the battery in fire.
- Do not expose the battery to direct sunlight for a long time nor place it close to other heating sources.
- Do not squeeze and penetrate the battery, nor remove its housing.
1.5 Transportation Instructions
- Damaged batteries must not be transported.
- To avoid short circuit, separate the battery from metal parts or from each other if two or more batteries are transported in one packaging.
- The radio must be switched off and secured against switch-on, if the battery is attached.
The content of the shipment must be declared in the shipping documents and by a Battery Shipping Label on the packaging. Contact your hauler for the local regulations and further information.
2. Setup
2.1 Content of the Packaging
This transceiver comes shipped with the following items in the box:
- 1 Radio body
- 1 Lithium-Ion battery pack
- 1 Instruction Manual
- 1 Belt Clip
- 1 Desk charger (With wall-wart)
- 1 Antenna
- 1 Wrist Belt
*If any item is missing, please notify your Baofeng / Pofung dealer.
Image: Package contents of the Baofeng UV18 Pro Max.
2.2 Installing / Removing the Battery
Installing the Battery Pack:
- Position the battery pack over the back of the radio.
- Engage the battery pack into the radio until battery pack is fully seated into the radio housing.
- Tighten the screws using a coin or at object to secure the battery pack to the radio. Do not overtighten.
To Remove Battery Pack from Radio:
- Loosen the screws on the back of the battery pack.
- Lift the bottom of the battery pack slightly to remove it from the radio housing.
- Pull the battery pack out of the radio housing.
NOTE: The Li-ON battery pack can also be charged in the battery charger.
2.3 Installing / Removing the Antenna
- Installing the Antenna: Screw the antenna into the connector on the top of the transceiver by holding the antenna at its base and turning it clockwise until secure.
- Removing the Antenna: Turn the antenna counter-clockwise to remove it.
2.4 Installing / Removing the Belt Clip
- Installing the Belt Clip: Place the belt clip above the corresponding holes on the back of the radio, and screw it into place clockwise with the two supplied screws.
- Removing the Belt Clip: Unscrew counter-clockwise to remove the belt clip.
2.5 Installing Additional Speaker/Microphone (Optional)
Pry open the rubber MIC-Headset jack cover and then insert the Speaker / Microphone plug into the double jack.
2.6 Charging the Battery Pack
The Li-ion battery pack is not charged at the factory; please charge it before use. Charging the battery pack for the first time after purchase or extended storage (more than 2 months) may not bring the battery pack to its normal maximum operating capacity. Best operation will require fully charging/discharging the battery two or three times before the operating capacity will reach its best performance. The battery pack life may be depleted when its operating time decreases even though it has been fully and correctly charged. If this is the case, replace the battery pack.
Please use the specified charger provided by Baofeng. Other models may cause explosion and personal injury. After installing the battery pack, and if the radio displays low battery with a red flashing lamp or voice prompt, please charge the battery.
How to Charge:
- Plug the AC adaptor into the AC outlet, and then plug the cable of the AC adaptor into the DC jack located on the back of the charger. The indicator light blinks orange and is then ready to charge battery.
- Plug the battery or the radio into the charger. Make sure the battery terminals are good in contact with charging terminals. The indicator light turns to red--- charging begins.
- It takes approximately 2-5 hours to fully charge the battery. When the lamp lights green, the charging is completed. Remove the battery or the radio unit with its battery from socket.
NOTICE: When charging a radio (with battery) the indicating lamp will not turn into green to show the fully charged status if the radio is powered on. Only when the radio is switched off will the lamp indicate normal operation. The radio consumes energy when it is power-on, and the charger cannot detect the correct battery voltage when the battery has been fully charged. So the charger will charge the battery in constant voltage mode and fail to indicate correctly when the battery has been fully charged.
LED Indicator during Charging:
| Red LED | Green LED | Status |
|---|---|---|
| Flashing | Steady | Standby (charger empty) / Error (charger with radio) |
| Steady | Off | Charging |
| Off | Steady | Charge complete. |
Using the Type-C Charger: The Type-C charger is a handy port that allows you to conveniently charge your Li-on battery pack.
- Make sure your radio is turned OFF.
- Plug the Type-C cable into the Type-C charging port on your battery. Connect the other end of the Type-C charger to wall power outlet.
- An empty battery will be fully charged in 6 hours.
- The battery meter on LCD will move to indicate the battery is charging.
Image: Various USB-C charging methods for the Baofeng UV18 Pro Max.
3. Operating Instructions
3.1 Radio Overview
Familiarize yourself with the components of your Baofeng UV18 Pro Max radio:
Image: Front and back view of the radio with key components labeled.
- Antenna
- Flashlight/ Emergency Alert key
- PTT key
- SK2 key (Customization key)
- MENU key
- Numeric keypad
- Power / Volume knob
- Color LCD
- Speaker/Mic Jacks
- MIC Input
- Exit Key
- ▲ or ▼ navigation keys
- Battery pack
- Type-C charging port
- Battery tightening screw
- Type-C charging indicator
- LED flashlight
- LED Status Indicator
3.2 Status Indications
The top LED will help you to identify the current radio status:
| LED Indication | What it Indicates |
|---|---|
| Constant Green | Receiving Signal |
| Constant Red | Transmitting signal |
| Flashes Green | Monitor mode/Scanning Receiving |
3.3 LCD Icon Summary
| Icon | Description |
|---|---|
| RSSI | Operating band signal |
| H | Transmit power level indicator, According to Power High |
| L | Transmit power level indicator, According to Power Low |
| ▲ | Make sure you can hear the DTMF side tone from the radio speaker, set to DT-ST, ANI-ST, DT+ANI. |
| D | DCS enabled |
| C | CTCSS enabled |
| + | Enables access of repeaters in VFO/Frequency Mode. TX will be shifted higher in frequency than RX. |
| - | Enables access of repeaters in VFO/Frequency Mode. TX will be shifted lower in frequency than RX. |
| D | Dual watch enabled |
| 🔒 | Keypad lock enabled |
| 💬 | VOX enabled |
| 🔊 | The confidential calling feature is activated |
| N | Narrowband enabled |
| 🔋 | Battery level indicator |
3.4 Basic Operations
3.4.1 Power On/Off the Radio:
- To turn the unit on: Simply rotate the Volume/Power knob clockwise until you hear a "click". If your radio powers on correctly there should be an audible double beep after about one second and the display will show a message or flash the LCD depending on settings for about one second. Then it will display a frequency or channel. If the Voice prompt is enabled, the voice will announce "frequency mode" or "channel mode".
- To turn the unit off: Turn the Volume/Power knob counter-clockwise all the way until you hear a "click". The unit is now off.
3.4.2 Adjusting the Volume:
- To turn up the volume, turn the Volume/Power knob clockwise.
- To turn the volume down, turn the Volume/Power knob counter-clockwise. Be careful not to turn it too far, as you may inadvertently turn your radio off.
By using the monitor function, enabled from the [FM broadcast/Monitor] key below the PTT, you can more easily adjust your volume by adjusting it to the un-squelched static.
3.4.3 Main Band/Sub Band Switch: In standby mode, press the ▲ key to switch between the main frequency band or sub frequency bands. The highlighted frequency band is the main frequency band, and the dimmed frequency band is the sub frequency band.
3.4.4 VFO/Channel Switch: Press and hold the MENU key to switch between VFO and channel display.
- In channel mode (MR), the channel number will be displayed on the right.
- In frequency mode (VFO), the ‘VFO' will be displayed on the right.
3.4.5 Frequency (VFO) mode: In Frequency (VFO) mode you can navigate up and down the band by using the ▲ or ▼ keys. Each press will increment or decrement your frequency according to the frequency step you've set your transceiver to. You can also input frequencies directly on your numeric keypad with kilohertz accuracy.
WARNING! Just because you can program in a channel does not mean you're automatically authorized to use that frequency. Transmitting on frequencies you're not authorized to operate on is illegal, and in most jurisdictions a serious offence. However, it is legal in most jurisdictions to listen. Contact your local regulatory body for further information on what laws, rules and regulations apply to your area.
3.4.6 Channel (MR) mode and Channel selection: There are two modes of operation: Frequency (VFO) mode, and Channel or Memory (MR) mode. For everyday use, Channel (MR) mode is going to be a whole lot more practical than Frequency (VFO) mode. In Channel (MR) mode you can navigate up and down the channel by using the ▲ or ▼ keys or the encoder.
3.4.7 Selecting a Bank: A bank is a group of channels with the same property. The radio supports up to 10 banks, with a maximum of 100 channels per bank. To select a bank, do one of the following: Press MENU key go to Menu > Bank, press ▲ or ▼ navigation key to select a bank, and then press MENU key to switch to the selected bank. The corresponding regional alias will be displayed at the bottom of the screen.
3.4.8 Making a Call:
- Channel mode call: After selecting a channel, hold down the [PTT] key to initiate a call to the current channel. Speak into the microphone with normal tone. Making a call, the red LED is on.
- Frequency mode call: Press and hold the MENU key to switch to the frequency mode, input the working frequency within the allowable frequency range, and press and hold the [PTT] key to transmit on the current frequency. Speak into the microphone with normal tone. Making a call, the red LED is on.
- Receive a call: When you release the [PTT] key, you can answer it without any action.
NOTE: To ensure the best reception volume, keep the distance between the microphone and the mouth at the time of transmission from 2.5 cm to 5 cm.
3.4.9 Using the Flashlight: You can use this radio in an emergency. If you press the flashlight key, the radio turns on the high-intensity LED flashlight on your radio.
- Press flashlight key once, it will turn on continuously (Always On mode).
- Press flashlight key once again, the Strobe Light emits the emergency signal (Strobe emergency mode).
- Press flashlight key a third time, the light will be turned off.
3.4.10 Emergency Alert: The Emergency Alert feature can be used to signal members in your group for help. To activate the emergency alert function, press and hold the flashlight key for 3 seconds. The radio will send out a loud siren sound and the flashlight will flash. Press the flashlight key to exit the emergency alert function.
WARNING: The Emergency Alert feature should only be used in the event of an actual emergency.
3.4.11 FM Radio (FM): The [SK2] key of the radio is defined as the FM radio on/off. The frequency ranges to listen to the radio is 65-108MHz. When listening to broadcast FM, press the ▲ key switches between 65-75 MHz and 76-108 MHz band.
- In frequency or channel mode, Press [SK2] key to turn on the radio.
- Select the desired radio frequency with the ▲ or ▼ keys or input the frequency.
- Press #z to automatically search a radio station.
- Press [SK2] key to exit FM radio.
Note: while you are listening to the radio, the frequency or channel of A / B receiving signal will automatically switch to the frequency or channel mode for normal transmitting and receiving. When the signal disappears the radio will automatically switch again to FM radio mode.
3.4.12 Monitor: In standby, press and hold the [SK2] key to enter Monitor. When receiving matched carrier but the signaling or the signal is too weak, this function allows monitor the weak signal. Stop pressing the [SK2] key to turn off the speakers and return to standby mode. If no signal, it will emit noise when press the [SK2] Key.
3.4.13 Keypad Lock: The radio features a keypad lock that locks out all keys except for the three side keys. To enable or disable the keypad lock, press and hold the * key for about two seconds. You can also enable so that the keypad automatically locks the keypad after ten seconds from the menu.
3.4.14 Frequency Reversal: A short momentary press of the * key enables the reverse function. If you for some reason want to listen to the repeater's input frequency instead, press * key momentarily and you'll reverse your transmit and receive frequencies.
3.4.15 TX Repeaters Tone: Press [PTT] + * key to send 1750Hz repeaters tone. This function is useful for communications through repeaters. If you have the keypad lock enabled on your radio, you can still send a 1750Hz tone the regular way without having to unlock your radio.
3.4.16 Weather Radio/Scan Weather Channel (NOAA): Your radio has a NOAA Weather Radio function, to enable the user to receive weather reports from designated NOAA stations. Your radio also has a NOAA Weather Scan function, to enable the user to scan all 10 channels of the NOAA Weather Radio.
Image: NOAA weather alert capabilities of the radio.
- To turn the NOAA Weather Scan on, press and hold the 0 key for 3 seconds, an icon appears. The radio will go to Weather band mode.
- Press and hold the #2 key for 3 seconds to start automatic scanning of all 10 channels and stop on active channels. Pressing and holding the #z key for 3 seconds during a NOAA weather scan will stop the scan.
- After stopping NOAA weather scan, it is allowed to manually select the weather channel by press the ▲ or ▼ key.
- To exit the Weather Radio broadcast mode, press the 0 key or [PTT] key.
Weather channel frequencies and names:
| Channel Number | RX Frequency MHz | Channel Number | RX Frequency MHz |
|---|---|---|---|
| CH-01 | 162.550 | CH-06 | 162.500 |
| CH-02 | 162.400 | CH-07 | 162.525 |
| CH-03 | 162.475 | CH-08 | 161.650 |
| CH-04 | 162.425 | CH-09 | 161.775 |
| CH-05 | 162.450 | CH-10 | 163.275 |
NOTE: Weather Channels Wx 1 Thru 10, Receive-only channels for NOAA and Canadian weather broadcasts. You cannot transmit on these channels.
3.4.17 One touch frequency Search:
- Through the CPS program software or the radio menu >> Radio Setting >> Press the SK2 key to define the SK2 side key as a Search function.
- The radio will act as a receiver. Briefly press the preset" Search "key, and the screen will display “SEARCH SEEK..."
- If the transmitter continues to transmit and the unit receives an effective frequency (the strongest and stable signal), the received frequency will be displayed. If there is a CTCSS or DCS, the CTCSS or DCS value is displayed, and if there is no CTCSS or DCS, NONE is displayed.
- You can press the MENU key to save the Search frequency and CTCSS or DCS to the channel.
Note: During frequency Search, press the # key on the radio to switch between UHF or VHF bands.
3.5 Advanced Features
3.5.1 Scanner: The radios features a built in scanner for the VHF and UHF bands. When in Frequency (VFO) mode it will scan in steps according to your set frequency step. In Channel (MR) mode it will scan your channels. To enable the scanner, press and hold the #2 key for about two seconds. You can change the scanning direction with the ▲ or ▼ keys. Press and hold the #2 key to exit scanning mode.
3.5.2 Scan Modes: The scanner is configurable to one of three ways of operation: Time, carrier or search, each of which is explained in further details in their respective section below.
- Time operation (TO): In Time Operation (TO) mode, the scanner stops when it detects a signal, and after a factory preset time out, it resumes scanning.
- Carrier operation (CO): In Carrier Operation (CO) mode, the scanner stops when it detects a signal, and after a factory preset time with no signal it resumes scanning.
- Search operation (SE): In Search Operation (SE) mode, the scanner stops when it detects a signal. To resume scanning you must press and hold the #2 key again.
Note: for Scan mode, see Menu>SCAN>Scan Mode.
3.5.3 Scan Sub-Code (CTCSS/DCS):
To search for a CTCSS code, do the following:
- In VFO mode, enter a known frequency, such as 144.525.
- Press MENU key to enter menu>>Scan>>3 Scan Sub-Code.
- Press ▲ or ▼ to select CTCSS;
- Press the MENU key to enter the CTCSS code, and scan the CTCSS code in turn. When a valid CTCSS code is scanned, it stays on the CTCSS code and the speaker is turned on.
- Press the MENU key to store the scanned CTCSS code and exit the scan to return to the previous menu. In standby mode, the C icon will be displayed on the top line of the screen. Press and hold the PTT key to make a callback.
To search for a DCS code, do the following:
- In VFO mode, enter a known frequency, such as 144.525.
- Press MENU key to enter menu>>Scan>>3 Scan Sub-Code.
- Press ▲ or ▼ to select DCS;
- Press the MENU key to enter the DCS code scanning, and scan the DCS code in turn. When a valid DCS code is scanned, it stays on the DCS code and the speaker is turned on.
- Press the MENU key to store the scanned DCS code and exit the scan to return to the previous menu. In standby mode, the D icon will be displayed on the top line of the screen. Press and hold the PTT key to make a callback.
Sub-Code scan storage: In MR mode or VFO mode, the scanned CTCSS/DCS code can be stored as only TX CTCSS/DCS code, RX CTCSS/DCS code only, TX and RX CTCSS/DCS code to replace the CTCSS/DCS code setting of the current channel or frequency mode of the radio. To save the settings of CTCSS/DCS code scan, the operation is as follows:
- Press MENU key to enter menu >> SCAN >> 4 Scan Memory.
- Press the MENU key to enter the Scan Memory setting, and press the ▲ or ▼ key to select:
- ALL: The scanned CTCSS/DCS code will be stored as the received and transmitted CTCSS/DCS code of the current channel or frequency mode (at the same time as the received and transmitted Sub-Code).
- DECODER: The scanned CTCSS/DCS code will be stored as the receiver CTCSS/DCS code of the current channel or frequency mode (only replace its receiver RX CTC/DCS).
- ENCODER: The scanned CTCSS/DCS code will be stored as the transmitted CTCSS/DCS code of the current channel or frequency mode (only replace its transmitted TX CTC/DCS).
- Press the MENU key to save the settings and return to the previous menu;
Note: Only when a valid CTCSS/DCS code is scanned and stopped, press the MENU key to store the CTCSS/DCS code and replace the corresponding CTCSS/DCS code of the current channel or frequency.
3.5.4 DTMF: DTMF is an in-band signaling method using dual sinusoidal signals for any given code. Originally developed for telephony systems, it has proved a very versatile tool in many other areas. In two-way radio systems, DTMF is most commonly used for automation systems and remote control. A common example would be in amateur radio repeaters where some repeaters are activated by sending out a DTMF sequence (usually a simple single-digit sequence).
DTMF frequencies and corresponding codes:
| 1209Hz | 1336Hz | 1477Hz | 1633Hz | |
|---|---|---|---|---|
| 697Hz | 1 | 2 | 3 | A |
| 770Hz | 4 | 5 | 6 | B |
| 852Hz | 7 | 8 | 9 | C |
| 941Hz | * | 0 | # | D |
The radios has a full implementation of DTMF, including the A, B, C and D codes. The numerical keys, as well as the * and #z keys correspond to the matching DTMF codes. The A, B, C and D codes are located in the ▲, ▼ and MENU keys respectively. To send DTMF codes, press the key(s) corresponding to the message you want to send while holding down the PTT key.
Call With Signaling: A call with signaling refers to a call make to a target ID on a channel with signaling. The signaling type is DTMF signaling, which needs to be preset signaling code, and the call is realized by encoding and decoding. Configure the signaling code, mute mode, and PTT-ID for the channel.
DTMF Manual Dial: Short press the #z key to enter DTMF manual dialing, enter the DTMF number in the following format, and press and hold the PTT key to make a DTMF call. The dialing format for DTMF calls to make Private call, Group call, and All call is as follows:
- Private call: Confirm the ID number with the #z key, and press and hold the PTT key.
- Group call: Confirm the ID number with the * key, and press and hold the PTT key.
- All call: Enter #z, press and hold the PTT key to make a DTMF all call.
3.5.5 Dual Watch: In certain situations, the ability to monitor two channels at once can be a valuable asset. This can be achieved in one of two ways. You can either have one receiver in your radio and flip-flop between two frequencies at a fixed interval (known as Dual Watch), or you can equip a radio with two receivers (known as Dual Receive or Dual VFO). The former method is cheaper to implement and far more common than the latter. The radio features Dual Watch functionality (single receiver) with the ability to lock the transmit frequency to one of the two channels it monitors.
Enabling or disabling Dual Watch mode:
- Press the MENU key to enter the main menu.
- Enter 3 on the numeric keypad to get to Radio Settings.
- Press the MENU key to confirm, enter 14 on the numeric keypad to get to 14 Dual Watch.
- Press the MENU key to select.
- Use the ▲ or ▼ keys to enable or disable.
- Press the MENU key to confirm.
- Press EXIT key to return to the previous menu.
The dual watch function is turned on, and the icon 'D' is displayed on the top line of the screen. To disable, repeat the above operation, select "OFF", the dual watch function is disabled, and the icon 'D' on the top line of the screen disappears.
3.5.6 Manual Programming (Channels Memory): Memory channels are an easy way to store commonly used frequencies so that they can easily be retrieved at a later date. The radios features 999 memory channels that each can hold: Receive and transmit frequencies, transmit power, group signaling information, bandwidth, ANI/ PTT-ID settings and a six character alphanumeric identifier or channel name.
Frequency Mode vs. Channel Mode: In standby mode, press and hold the MENU key to switch between frequency (VFO) mode and channel (MR) mode. These two modes have different functions and are often confused.
- Frequency Mode (VFO): Used for a temporary frequency assignment, such as a test frequency or quick field programming if permitted.
- Channel Mode (MR): Used for selecting preprogrammed channels.
3.5.7 Repeaters Programming: The following instructions assume that you know what transmit and receive frequencies your repeater employs, and that you're authorized to use it.
- Press and hold the MENU key, the transceiver is set to VFO mode, and the VFO icon will be displayed on the right.
- Use the numeric keypad to enter the repeater's output (your receive) frequency.
- Press [4]=[1][4]= to get the offset frequency.
- Use the numeric keypad to enter the specified frequency offset.
- Press MENU key to confirm and save.
- Press [4]=[1][5]= to get the offset direction.
- Use the ▲ or ▼ keys to select plus (positive) or minus (negative) offset.
- Press MENU key to confirm and save.
- (Optional) Save to memory, see the section called “Manual programming" for details. Set up CTCSS; see the section called “CTCSS” for details.
- Press EXIT key to exit the menu. If everything went well, you should be able to make a test call through the repeater.
NOTE: If you're experiencing problems making a connection to the repeater, check your settings and/or go through the procedure again. Certain Amateur Radio repeaters (especially in Europe) use a 1750Hz tone burst to open up the repeater. To see how this is done with the radios, see the section called “1750Hz Tone-burst”. If you're still unable to make a connection, contact the person in charge of the radio system with your employer or your local amateur radio club, as the case may be.
3.6 Main Menu Functions
The menu function allows you to perform operations such as selecting Banks, Setting SCAN, Radio Settings, Program Channels, and viewing Radio Information.
3.6.1 Basic use: Use menus with arrow keys
- Press the MENU key to enter the main menu.
- Use the ▲ or ▼ keys to navigate between menu items.
- After finding the desired next menu item, press the MENU key again to select the menu item.
- Use the ▲ or ▼ keys to navigate between the next menu items.
- After finding the desired next menu item, press the MENU key again to select the menu item.
- Use the ▲ or ▼ keys to select the desired parameter.
- When you have selected the parameter to be set for a given menu item;
- To confirm your selection, press MENU and it will save your setting and bring you back to the main menu.
- To cancel your changes, press EXIT and it will reset that menu item and bring you out of the menu entirely.
- To exit out of the menu at any time, press the PTT key.
3.6.2 Using Short-cuts: Every menu item has a numerical value associated with it. These numbers can be used for direct access of any given menu item.
Using the menu with short-cuts:
- Press the MENU key to enter the menu.
- Use the numerical keypad to enter the number of the menu item.
- To enter the menu item, press the MENU key.
- For entering the desired parameter you have two options: a) Use the arrow keys as we did in the previous section; or b) Use the numerical keypad to enter the numerical short-cut code.
- To confirm your selection, press MENU and it will save your setting and bring you back to the main menu. To cancel your changes, press EXIT and it will reset that menu item and bring you out of the menu entirely.
- To exit out of the menu at any time, press the PTT key.
Quick Access Shortcuts:
- + 1: Quick access to Banks selection, up to 10 banks are stored, each bank stores 100 channels;
- + 2: Quickly enter the Scan Settings. You will be able to set the VFO frequency range, Scan mode, Scan Sub-Code, Scan Memory;
- + 3: Quickly enter the Radio settings (general settings of the radio);
- + 4: Quick access to Program Channel (Alias, TX and RX Frequency, TX Power, Bandwidth, Display mode, Channel Memory
- + 5: Quickly query the radio information (ANI ID, Firmware version, Hardware version);
3.6.3 Radio Settings:
- (1) Step frequency (Step) – MENU + 1: This function lets you select the desired frequency step. The selectable steps are the following: 2.5K/5.0K/6.25K/10K/12.5K/20K/25K/50K/100K. Note: in channel mode, this function cannot be modified.
- (2) Squelch level (Squelch) – MENU + 2: This function allows you to adjust the squelch in 5 different levels: OFF (opened squelch), Levels 1-5 (level 1 lowest, level 5 highest).
- (3) Power save (Power Save) – MENU + 3: When the radio is in standby, the power saving function reduces battery consumption. Turning on will be more power efficient, but you may miss the first few syllables before RX turns on.
- (4) VOX Function (Vox Switch) – MENU + 4: The VOX feature allows hands-free calls without using the PTT button. As soon as you speak into the microphone, communication will start automatically. ON activates, Off turns off.
- (5) VOX Level (Vox Level) – MENU + 5: From this menu, you can select the VOX sensitivity level. The selection range is from 1 to 9. Note: Level 1 is the least sensitive, while level 9 is the most sensitive. The VOX feature is not enabled when the radio is in scan or FM radio mode.
- (6) VOX Delay – MENU + 6: When the VOX is enabled, set up the VOX delay to help to extend the transmission time to avoid stopping a transmission too early. Range 0.5 - 2.0 seconds. Step 0.1 second. Default 1 seconds.
- (7) Time-Out-Timer (TOT) – MENU + 7: The Time-Out Timer (TOT) sets the duration that the radio can continuously transmit before transmission is automatically terminated. This feature is used to prevent any single user from occupying a channel for too long. Range: Off, 15 –180 seconds, Step 15 seconds. Default 60 seconds. Note: If this option is set to OFF, press and hold the PTT key to keep transmission.
- (8) Transmission Overtime Alarm (TOA) – MENU + 8: Allows users to define a duration an alert will be given before terminating the transmission. Range 0 – 10 seconds, Step 1 second. Default Off.
- (9) Voice prompts function (Voice) – MENU + 9: With this function, you activate a voice that informs you about any operation/ selection you are doing.
- (10) Language selection (Language) – MENU + 10: With this function, you can select the language of the LCD display and operation prompt.
- (11) Roger beep (ROGER) – MENU + 11: When the PTT is released, the radio will beep to confirm to other users that you have finished your transmission and that they can start talking.
- (12) Keypad beep (Beep) – MENU + 12: When this function is enabled, every time a key is pressed, you will hear a beep tone.
- (13) Backlight (Backlight) – MENU +13: With this function you can adjust the auto off time of the display backlight. Always: The backlight is always on. 5S-20S adjustable. Note: This function is valid when turn off the power save.
- (14) Power on image (Power on Display) – MENU + 14: With this function you can set the display mode when the radio is turned on. Available options: PICTURE (Display the preset startup picture), MESSAGE (Welcome message), VOLTAGE (The power voltage is momentarily displayed).
- (15) Dual Watch Operation (Dual Watch) – MENU + 15: When this function is activated, you can receive the frequency of channel A and channel B at the same time. If a signal is detected, the ▲ or ▼ pointer will blink on the corresponding channel or frequency.
- (16) Auto Keypad Lock (AutoLock) – MENU + 16: When this feature is activated, the keypad will be automatically locked after 10s; this prevents accidental pressure of any keys. The keypad lock can be manually activated/deactivated through the keypad: keep pressed * key.
- (17) Alarm Mode (Alarm Mode) – MENU + 17: This function can set the tone alarm/code alarm/site alarm of the radio. Keep pressed the [SK1] key for 3 seconds to start the alarm tone. The following three options can be selected: Site (speaker emits an alarm tone but radio doesn't transmit), Tone (speaker emits an alarm tone and radio transmits it), Code (speaker emits an alarm tone and radio transmits it followed by ANI-ID code).
- (18) Local Alarm Tone (Alarm Tone) – MENU + 18: Whether to emit an alarm whistle locally when the emergency alarm function is triggered.
- (19) ANI-ID (ANI-ID) – MENU + 19: Displays the ANI code set by the software. Manual changes are allowed if necessary, and you can edit up to 5 digits. ANI-ID is sent when alarm is active and menu 16 = SEND CODE. The ANI-ID will be sent during DTMF signaling calls.
- (20) DTMFST (DTMFST) – MENU + 20: Determines when DTMF Side Tones can be heard from the transceiver speaker. You can choose amongst four options: Off, DT-ST, ANI-ST, DT+ANI.
- (21) PTT-ID (PTT-ID) – MENU + 21: When to Send PTT-ID Codes are sent during either the beginning or ending of a transmission. With this function you can decide when sending the ANI-ID code in tx mode. You can choose amongst 4 possibilities: Off, BOT, EOT, BOTH.
- (22) Signal code sending delay (PTT-DLY) – MENU + 22: PTT-ID signal code sending delay time setting, range 100-3000ms.
- (23) 1750Hz Repeater Tone (ALERT) – MENU + 23: With this function you can select 1000Hz, 1450Hz, 1750Hz, 2100Hz repeater tone. To send out a repeater tone; You hold down the [PTT] + * key.
- (24) Squelch tail elimination (TAIL) – MENU + 24: This function is used eliminate squelch tail noise between handhelds that are communicating directly (no repeater). Reception of a 55 Hz or 134.4 Hz tone burst mutes the audio long enough to prevent hearing any squelch tail noise.
- (25) SK2 function definition(Press SK2) – MENU + 25: The SK2 key allows users to customize functions: FM RADIO (on/off), SCAN (on/off), SEARCH (one touch Search on/off), VOX (on/off).
- (26) Reset (Reset) – MENU + 26: With this function you can reset the transceiver to the factory-programmed settings and parameters. There are two types of reset: VFO (Menu Reset), ALL (Menu and channel Reset).
3.6.4 Program Channel: Channel configuration is only applicable to the current channel and will not change the configuration parameters of other channels. It allows to modify the channel name, Receive or Transmit frequency, Tx_Rx CTCSS/DCS, add the current channel to the scan list, Working Mode, and channel memory and channel delete.
- (1) Channel name (CHNAME) – MENU +1: To set the channel name you have at your disposal 26 letters (A-Z) and 10 numbers (0-9). You can use up to 8 characters for the channel name. Edit the desired channel name with the keypad and then confirm by pushing MENU key. To exit the function press EXIT key.
- (2) RX Frequency – MENU +2: Input the RX frequency by keypad, click the MENU key to save, press EXIT key to return.
- (3) TX Frequency – MENU +3: Input the TX frequency by keypad, click the MENU key to save, press EXIT key to return.
- (4) Transmit power (Tx Power) – MENU +4: Set up the TX power for current channel.
- (5) Wide/Narrow Bandwidth – MENU +5: Select wideband or narrowband for the current channel. Wide: 25 KHz; Narrow: 12.5 KHz.
- (6) Receiving CTCSS (Rx CTCSS) – MENU +6: As DCS codes, the CTCSS codes can be added to the channels for creating new private channels. Note: there are 50 groups of CTCSS tones.
- (7) Receiving DCS (Rx DCS) – MENU + 7: DCS codes are similar to access codes and can be added to channels, so as to create a sort of personal channel. They enable the radio to communicate with the users that are tuned on the same channel and have set the same DCS code. You can choose amongst: Off, D023N-D754N (Normal DCS), D023I-D7541 (Inverse DCS). Note: In radio there are 208 groups of normal and inverse DCS codes.
- (8) Transmitting CTCSS (Tx CTCSS) – MENU +8: In this Menu you can set a CTCSS tone in tx mode. You can choose: Off or CTCSS (67.0 to 254.1 Hz). Note: there are 50 groups of CTCSS tones.
- (9) Transmitting DCS (Tx DCS) – MENU+9: In this Menu you activate DCS codes in tx mode. You can choose between normal R-DCS (D023N-D754N) and inverted R-DCS (D0231-D754I). Note: the groups of DCS codes are 208.
- (10) Call Encryption (Encryption) – MENU +10: If the channel is configured with CTCSS/DCS and encryption is turned on, the communication will remain private. The encryption icon will be displayed on the screen when the encryption function is turned on.
- (11) Signal code (Signaling) – MENU +11: Selects 1 of 20 DTMF codes. The DTMF codes are programmed with software and are up to 3 digits each.
- (12) Working Mode (CH-MDF) – MENU +12: This function is used to set the display mode of the current channel. The radio offers three working modes: NAME (Channel name), FREQ (Frequency Mode), CH (Channel Mode).
- (13) Monitor (SP-MUTE) – MENU +13: With this function, the monitor opens if one of these options is detected: QT (correct CTCSS tones), QT + DTMF (correct CTCSS tone and DTMF code), QT*DTMF (correct CTCSS/DCS or DTMF code).
- (14) Scan Add (Scan Add) – MENU+14: In channel mode, to scan the current channel, the channel must be added to the scan group. On (Turn on the scan function), Off (Do not scan the current channel).
- (15) Busy Channel Lock (Busy Lock) – MENU+15: When this function is on, it may prevent other radios' interference. If the selected channel is being used by other radios, when you press key PTT, your radio cannot transmit. Release the PTT and transmit as soon as the frequency is no longer busy.
- (16) Channel Memory - (CH-Memory) – MENU +16: This menu is used to either create new or modify existing channels (1 through 100) so that they can be accessed from MR/Channel Mode.
- (17) Channel Delete (CH-Delete) – MENU +17: This menu is used to delete the programmed information from the specified channel (1 through 100) so that it can either be programmed again or be left empty.
3.6.5 Radio Info: Show the Radio ID, firmware version, Hardware version.
4. Maintenance
4.1 Battery Maintenance
The battery for your radio comes uncharged from the factory; please let it charge for at least four to five hours before you start using your radio.
- Use only batteries approved by the original manufacturer.
- Never attempt to disassemble your battery pack.
- Do not expose your batteries to fire or intense heat.
- Dispose of batteries in accordance with local recycling regulations. Batteries do not belong in your trashcan!
4.2 Prolonging the Life of Your Battery
- Only charge batteries in normal room temperatures.
- When charging a battery attached to the radio, turn the radio off for a faster charge.
- Do not unplug the power to the charger or remove the battery and/or radio before it's finished charging.
- Never charge a wet battery.
- Batteries wear out over time. If you notice a considerably shorter operating time with your radio, please consider purchasing a new battery.
- Battery performance will be reduced in temperatures below freezing. When working in cold environments, keep a spare battery on you. Preferably inside your jacket or in a similar location in order to keep the battery warm.
- Dust can interfere with the contacts on the battery. If necessary wipe the contacts with a clean cloth to ensure proper contact with radio and charger.
If your battery has become wet, remove it from the radio, wipe it dry with a towel and put it in a plastic bag with a handful of dry rice. Tie the bag up and let it sit over night. The rice will absorb any remaining moisture in the battery. This method is only effective against minor splashes (light rain for instance). A soaked radio may very well be beyond repair.
4.3 How to Store the Battery
- If the battery needs to be stored, keep it in status of 80% discharged.
- It should be kept in low temperature and dry environment.
- Keep it away from hot places and direct sunlight.
- To avoid severe capacity degradation of your battery while in long-term storage, please cycle the battery at least every six (6) months.
NOTICE: Do not short circuit the battery terminals. Never attempt to remove the casing from the battery pack. Never store the battery in unsafe surroundings, as a short may cause an explosion. Do not put the battery in a hot environment or throw it into a fire, as it may cause an explosion.
5. Troubleshooting Guide
| Phenomena | Analysis | Solution |
|---|---|---|
| You cannot turn on the radio. | The battery may be installed improperly. The battery power may run out. The battery may suffer from poor contact caused by dirty or damaged battery contacts. The battery voltage maybe low. |
Remove and reattach the battery. Recharge or replace the battery. Clean the battery contacts or replace the battery. Recharge or replace the battery. |
| During receiving, the voice is weak or intermittent. | The volume level may be low. The antenna maybe loose or maybe installed incorrectly. The speaker maybe blocked. |
Increase the volume. Turn off the radio, and then remove and reattach the antenna. Clean the surface of the speaker. |
| You cannot communicate with other group members. | The frequency or signaling type maybe inconsistent with that of other members. You may be too far away from other members. You may be interrupted by radios using the same frequency. |
Verify that your TX/RX frequency and signaling type are correct. Move towards other members. Change the frequency, or adjust the squelch level. |
| You hear unknown voices or noise. | The radio in analog mode maybe set with no signaling. | Request your dealer to set signaling for the current channel to avoid interference. |
| You are unable to hear anyone because of too much noise and hiss. | You may be too far away from other members. You may be in an unfavorable position. For example, your communication may be blocked by high buildings or blocked in an underground area. It may be the result of external disturbance (such as electromagnetic interference). |
Move towards other members. Move to an open and flat area, restart the radio, and try again. Stay away from equipment that may cause interference. |
| The radio keeps transmitting. | VOX may be turned on or the headset is not installed in place. | Turn off the VOX function. Check that the headphones are in place. |
NOTE: If the above solutions cannot fix your problems, or you may have some other queries, please contact your dealer for more technical support.
6. Technical Specifications
6.1 General
| Channel Capacity | 1000 |
| Channel Spacing | 25.0 KHz/12.5 KHz |
| Input Voltage | 7.4 VDC |
| Battery Life: 5% TX, 5% RX, 90% Standby | Li-on: 15 hours @ 5 watts |
| Current Drain: Stand-by | 45 mA |
| Receive | 200 mA |
| Transmit | ≤1.6 A @ High Power , ≤1.2 A @ Low Power |
| Operating temperature | -10°C to 60°C |
| Antenna Impedance | 50Ω |
| Radio Dimensions | 127mm X 69mm X 38mm (not including antenna) |
6.2 Transmitter
| Frequency Range (TX) | 136 to 174 MHz, 220 to 260 MHz, 400 to 480 MHz |
| RF Output Power | 2 or 5 Watts Max |
| Modulation | 16KØF3E/11KØF3E |
| Spurious Emission | -16 dBm<1GHz, -16 dBm>1GHz |
| Frequency Stability | ±2.5 ppm |
| Audio Distortion | ≤5% |
| FM Hum & Noise | 40 dB |
6.3 Receiver
| Frequency Range | 136 to 174 MHz, 220 to 260 MHz, 400 to 520 MHz, FM78 to 108MHz, AM 108 to 136MHz, 350 to 390 MHz |
| Sensitivity: 12 dB SINAD | -120 dBm |
| Adjacent Channel Selectivity | -60 dBm |
| Intermodulation and Rejection | -70 dBm |
| Rated Audio Power Output | 1.0 Watts @ 16 Ω |
| Rated Audio Distortion | ≤5% |
NOTE: All specifications may be modified without prior notice or liability. Thank you.
7. User Tips
No specific user tips were provided from reviews or Q&A content. For optimal performance, ensure your battery is fully charged before use and refer to the troubleshooting section for common issues.
8. Warranty and Support
For technical support or inquiries, please contact the manufacturer:
Fujian Baofeng Electronics Co.,Ltd.
ADD: Changfu Industrial Bank Xiamei, Nan'an, Quanzhou, Fujian, China
E-mail: wangjianhui@baofengradio.com
Website: http://www.baofengradio.com
A PDF version of this user manual is available for download: User manual (PDF)