INQMEGA 637-60X

Contents

INQMEGA 637-60X Solar Camera User Manual

Model: 637-60X

1. Introduction

The INQMEGA 637-60X Solar Camera is an advanced outdoor security solution featuring 12MP Ultra HD resolution, 60X optical zoom, and dual-lens technology. Powered by a solar panel and built-in battery, it offers wire-free operation and supports both 4G and WiFi connectivity. Key features include PIR human detection, human tracking, two-way audio, and versatile night vision modes.

2. Product & Packing List

2.1 Product Diagram

Below is a diagram illustrating the main components of the INQMEGA Solar Camera.

Product diagram showing antenna, wide-angle lens, IR/white LEDs, LED indicator, zoom lens, light sensor, microphone, and PIR sensor.
  • Solar Panel: For continuous power.
  • Antenna: For network connectivity.
  • Wide-Angle Lens: Provides a broad view.
  • IR LED/White LED: For night vision (default IR LED, switchable to white LED for color night vision).
  • LED Indicator: Shows device status.
  • Zoom Lens: For detailed viewing and optical zoom.
  • Light Sensor: Detects ambient light for automatic mode switching.
  • Microphone: For audio input.
  • PIR Sensor: For passive infrared human detection.

2.2 Battery Interface

The camera features a recharge port and a power switch for battery management.

Diagram showing the battery interface with recharge port and power switch.

ATTENTION: Fully charge the battery before using the camera for the first time. A full charge takes approximately 7 hours with a DC 5V 2A power supply.

2.3 Package Contents

The following items are included in your product package:

Detailed list of products including camera, solar panel, user manual, camera bracket, solar panel bracket, and power cable.
  • Camera x 1
  • Solar Panel x 1
  • User Manual x 1
  • Camera Bracket x 1
  • Solar Panel Bracket x 1
  • Power Cable x 1

2.4 Product Dimensions

The camera and solar panel have the following approximate dimensions:

Solar panel dimensions: 183mm height, 168mm width.

Solar Panel: 183mm (Height) x 168mm (Width)

Camera dimensions: 180mm height, 100mm width, 123mm antenna height.

Camera: 180mm (Height) x 100mm (Width) x 102mm (Depth, excluding antenna)

3. Specifications

FeatureDescription
Resolution12MP (6MP Wide-angle + 6MP Zoom Lens)
Optical Zoom60X (20X optical zoom on the zoom lens)
Lens2.8mm wide-angle lens + 5-50mm zoom PTZ lens
Pan/Tilt RotationPan 355°, Tilt 100°
Connectivity2.4G WiFi (IEEE 802.11 b/g/n) or 4G Network
Power SourceSolar Panel (6W) with Built-in 10050mAh Battery
Night VisionColor Night Vision (white light) or IR Night Vision (infrared light), 40m IR distance
DetectionPIR Human Detection (up to 12 meters), AI Humanoid Detection, Human Tracking
AudioTwo-way Voice Intercom (built-in microphone and speaker)
StorageTF Card (max 128GB, not included) and Cloud Storage
AppUBox app (iOS/Android)
Waterproof RatingIP65
InstallationNormal (Wall Mount, Ceiling Hanging)
CertificationCE
Product features icons: 12MP Super HD, 50X Zoom, Dual View, Dual Lens, PIR Human Detection, Human Tracking, Solar Panel, Built-in Battery, Color/IR Night Vision, Two-way Audio, IP65 Waterproof, TF Card & Cloud Storage.

4. Installation

The camera supports multiple installation methods, including wall mounting and ceiling hanging. Choose the method that best suits your environment.

4.1 Installation Methods

Diagram showing steps for Ceiling Hanging Installation and Wall Mounting Installation.

Ceiling Hanging Installation:

  1. Secure the camera bracket to the ceiling using screws.
  2. Attach the camera to the bracket.
  3. Connect the power cable.

Wall Mounting Installation:

  1. Secure the camera bracket to the wall using screws.
  2. Attach the camera to the bracket.
  3. Connect the power cable.

4.2 Adjusting the Wide-angle Lens

The wide-angle lens can be manually adjusted by 350° to achieve the desired field of view.

Image showing manual adjustment of the wide-angle lens by 350 degrees.

4.3 PTZ Rotation

The camera supports Pan/Tilt/Zoom (PTZ) rotation, allowing you to control its viewing angle remotely via the app. It can pan 355° and tilt 90°.

Image demonstrating PTZ rotation with 355 degree pan and 90 degree tilt, controlled via a smartphone app.

4.4 Solar Panel Connection

Connect the camera to the solar panel for uninterrupted power supply. The solar panel is designed for fast absorption, high conversion, and fast charging.

Diagram showing the solar panel connected to the camera, highlighting fast absorption, high conversion, and fast charging.

4.5 Installation and Feature Demonstration Video

This video demonstrates the installation process, PTZ rotation, 20X zoom, human tracking, PIR human detection, IP65 waterproof rating, and night vision capabilities of the camera.

5. App Registration

5.1 Download the UBox App

Scan the QR code below or search for "UBox" in the App Store (for iOS devices) or Google Play Store (for Android smartphones) to download and install the application.

QR code for UBox app download on iOS/Android.

iOS / Android

5.2 Register an Account

Open the UBox app, enter your email address, and click "Register". Agree to the terms, and a verification code will be sent to your email. For a better user experience, allow all necessary permissions for the app.

6. Network Connection

The camera supports both 4G and WiFi network connections. If Bluetooth configuration is not supported or fails, follow the manual steps below.

6.1 Initial Setup

  1. In the app, click "Add Family" and set the room or position as prompted.
  2. Enter your family name and click "Next".
  3. Input the necessary information (Country, Province) and click "Finish".
  4. Click "Setup 4G Device" or "Setup WiFi Device" to proceed.

6.2 4G Camera Card Slot

Insert the TF card and SIM card into the designated slots. Ensure metal chips face the correct direction as shown in the diagram. The camera will power on, and the 4G network status indicator will show its status.

Diagram showing how to insert TF card and SIM card into the 4G camera card slot.
  • TF card Metal chips facing UP
  • SIM card Metal chips facing down
  • Reset Button: Touch for 5 seconds to reset the camera (useful for re-connecting or initial setup).

6.3 4G Network Status Indicator

  • Red light ON: Power on now.
  • Red and Blue lights flash slowly and alternately: No 4G SIM card recognized.
  • Red and blue lights flash quickly: Searching 4G network.
  • Blue light keeps ON: 4G connection successful.

If the network is not configured for more than five minutes, the camera will go to sleep, and the blue indicator will turn off. You need to power on again to reconfigure.

6.4 WiFi Network Connection

For WiFi models, ensure your device supports 2.4GHz WiFi. The total letters for both username and password of your 2.4GHz WiFi router should be less than 32.

  1. After powering on the device, wait for about 1 minute until the device blue LED lights up.
  2. In the app, enter the 2.4GHz WiFi account password and click "Configuring devices".
  3. Align the QR code displayed on your phone with the camera lens to scan it. Keep a distance of about 10cm between the phone and the camera.
  4. Once the connection is successful, click "OK" to complete.

7. Device Settings

7.1 PIR Detection Settings

You can adjust the PIR detection sensitivity in the device settings to optimize performance and battery life. This is crucial in noisy environments to reduce false alerts.

  • Disabled: PIR detection is off.
  • Low: 7-second delay before detecting movement.
  • Medium: 5-second delay before detecting movement.
  • High: 1-second delay before detecting movement.

7.2 Dual View Monitoring

The UBox app allows for dual-view simultaneous monitoring, displaying both the wide-angle and zoom lens feeds on the same screen. Double-click to switch views.

Smartphone screen showing dual-view monitoring from the camera's wide-angle and zoom lenses.

7.3 Preset Points & Guards

Set preset points in advance to quickly view important areas without manual adjustment.

Diagram showing a house with four numbered preset positions for the camera.

7.4 Night Vision Modes

The camera features both white light and IR LED light, allowing you to switch between color night vision and infrared (IR) night vision modes.

Comparison of color night vision and IR night vision modes from the camera.

7.5 Two-way Audio

With a built-in microphone and speaker, you can easily communicate through your wireless camera.

Image showing a delivery person talking to someone through the camera's two-way audio feature.

7.6 Multiple Storage Methods

The camera supports automatic recording and storage of audio and video to both a TF card (up to 128GB) and cloud storage, ensuring safe backup of important information.

Image illustrating TF card and cloud storage options for the camera, with a smartphone screen showing recorded activity.

8. Troubleshooting

8.1 Camera Not Rotating or Waking Up

Problem: The camera cannot rotate in any direction or wake up by PIR, and only remote video viewing is possible, even if the battery appears full.

Reason: The battery power may have dropped below the working voltage at some point, causing the protection circuit to turn off.

Action: Re-enable the battery's protection circuit. Use a Type-C cable to recharge the camera with a DC 5V power supply for about 2-5 seconds. This should allow the camera to rotate again. (Note: Only the Type-C port can enable the protection circuit).

Diagram showing correct (DC 5V) and incorrect (DC 5V~9V/12V/20V) charging methods for the camera battery.

Forbiddance: Do NOT always charge batteries with Type-C port when the camera is working.

8.2 4G Network Connection Issues

Problem: The 4G camera's red indicator light remains on after inserting the SIM card and powering on.

Action: Check the "APN name, MNC, MCC" information in your mobile phone's settings (access point). Verify if this 4G signal from your local telecom operator matches the camera's requirements. If issues persist, contact the seller for further solutions.

8.3 Weak WiFi Signal

Problem: The camera experiences weak WiFi signal or frequent disconnections.

Action: Ensure the camera is within range of your WiFi router. If there are thick or insulated objects between the camera and the router, reposition them to improve signal strength. Verify that the WiFi signal level is good before using the device.

9. User Tips

  • Always fully charge the camera battery before its first use to ensure optimal performance and longevity.
  • Adjust PIR detection sensitivity to 'Low' or 'Disabled' in high-traffic areas to conserve battery life and reduce false alarms.
  • For clear and detailed images, utilize the 60X optical zoom feature. The camera provides effective calibration for precise viewing.
  • When using the app, take advantage of the dual-view monitoring to keep an eye on both wide-angle and zoomed perspectives simultaneously.
  • Ensure the camera is placed within optimal range of your WiFi router for stable connectivity.

10. Safety Information

Disclaimer: Camera products can only be used for purposes permissible under applicable law and regulations. Misuse of the product for any illegal activities is strictly forbidden. Please comply with the applicable laws and regulations in your country/area.

  • Remove all protective films from the camera before use.
  • Do not continuously charge the camera batteries with a Type-C port while the camera is working, as this can damage the battery.
  • Ensure proper installation to prevent the camera from falling or being damaged by environmental factors.
  • Keep the camera and solar panel clean to maintain optimal performance.

11. Warranty & Support

For detailed warranty information and further support, please refer to the official user manual PDF available at: User Manual (PDF). You may also contact the seller directly for assistance.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.