Introduction
Thank you for choosing the HOMEFISH Smart Sensor Automatic Soap Dispenser. This device provides a hygienic and convenient way to dispense foam soap or hand sanitizer without direct contact, promoting better hand hygiene. This manual will guide you through the setup, operation, maintenance, and troubleshooting of your new dispenser.

Setup
1. Unpacking and Initial Charge
Carefully remove all components from the packaging. The package includes the main unit, a USB charging cable, and this instruction manual.
Before first use, ensure the device is fully charged. Connect the provided USB Type-C charging cable to the dispenser's charging port and to a 5V/0.5A USB power source. The yellow light will flash during charging and remain on when fully charged.

2. Filling the Dispenser
- Remove the top cover of the dispenser.
- Pour liquid soap into the reservoir. The dispenser supports two types of soap:
- Foaming Hand Soap: Can be used directly.
- Normal Liquid Hand Soap: Must be diluted with water at a 1:4 ratio (1 part soap to 4 parts water) to create foam.
- Replace the top cover securely.
Note: When filling for the first time or after the liquid has run out, the dispenser may need 2-3 cycles of air evacuation before it dispenses liquid normally.

3. Placement
The dispenser is designed for bench-mounted installation. It is suitable for various environments including hotel bathrooms, home bathrooms, hospital bathrooms, and public sinks.

Operating Instructions
1. Power On/Off
- To Power On: Touch the power button. The green indicator light will turn on, indicating the first gear is active.
- To Power Off: Press and hold the power button for 1.5 seconds. The red light will turn on briefly, then the device will shut down.
2. Adjusting Dispensing Volume (Gears)
The dispenser has 4 adjustable gears, each corresponding to a different liquid outlet time. Touch the power button repeatedly to cycle through the gears:
- First Gear: Green indicator light. Dispensing time: 0.5 seconds.
- Second Gear: Blue indicator light. Dispensing time: 0.8 seconds.
- Third Gear: Purple indicator light. Dispensing time: 1.1 seconds.
- Fourth Gear: White indicator light. Dispensing time: 2.5 seconds.
After the fourth gear, touching the button again will return to the first gear (green light).

3. Automatic Dispensing
Once the dispenser is powered on and a gear is selected, simply place your hand under the sensor area. The infrared sensor will detect your hand within a distance of 4-6cm and automatically dispense foam soap for the selected duration.

Maintenance
- Cleaning the Sensor: If the red light flashes in standby mode, it indicates that the sensor is blocked by foreign matter. Wipe the sensor area clean with a soft cloth before normal use.
- Cleaning the Body: Do not flush the main unit directly with water, as this may damage the internal electronic components. Use a damp cloth to wipe the exterior.
- Storage: If the dispenser will not be used for an extended period, turn it off and store it in a dry place.
- Preventing Leakage: Do not tilt the dispenser body excessively to avoid liquid leakage.
- Avoid Impact: Do not strike the machine violently, as this can cause serious damage.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Red light flashes during liquid dispensing | Low battery | Charge the dispenser using the provided USB Type-C cable. |
| Red light flashes in standby mode | Sensor blocked by foreign matter | Wipe the sensor area clean with a soft cloth. |
| No liquid dispensed after refilling | Air trapped in the pump system | Place your hand under the sensor 2-3 times to evacuate air until liquid dispenses normally. |
| Device not working or damaged | Improper charging voltage, strong impact | Ensure only 5V charging voltage is used. Avoid dropping or hitting the device. |
Specifications
| Feature | Detail |
|---|---|
| Product Name | Smart Sensor Automatic Soap Dispenser |
| Brand | HOMEFISH |
| Model | Automatic Foam Dispenser |
| Bottle Capacity | 350ml (also available in 600ml variant) |
| Battery Capacity | 2000mAh (3.7V/1200mAH 18650 rechargeable battery) |
| Charging Interface | USB Type-C |
| Rated Charging Voltage | 5V/0.5A |
| Standby Time | Over 3 months |
| Sprays per Charge | Over 4000 times (up to 10800 times) |
| Product Material | ABS, PET, Silicone |
| Sensing Distance | 4-6 cm (infrared induction) |
| Waterproof Rating | IPX5 |
| Operating Temperature | 3°C ~ 55°C |
| Net Weight (no liquid) | 223g |
| Dimensions (350ml model) | 112mm (L) x 76mm (W) x 178mm (H) |
| Dimensions (600ml model) | 112mm (L) x 76mm (W) x 210mm (H) |
| Installation Method | Bench mounted |

User Tips
- Optimal Soap Usage: For best foaming results, use dedicated foaming hand soap. If using regular liquid hand soap, always dilute it with water at a 1:4 ratio (1 part soap to 4 parts water) before filling the dispenser. This prevents clogging and ensures consistent foam.
- Sensor Responsiveness: Ensure the sensor area is clean and unobstructed for reliable and quick dispensing.
- Battery Life: A full charge provides extensive use. If you notice the red light flashing during dispensing, it's a good indicator to recharge soon.
Warranty and Support
For detailed warranty information and further support, please refer to the official user manual PDF provided by the manufacturer. You can access the PDF manual here.
For any product-related inquiries or technical assistance, please contact HOMEFISH customer support.