1. Introduction
Welcome to the ANDELI Family! This manual provides essential information for the safe and efficient operation of your ANDELI CUT-65DS 65A Plasma Cutter. Please read this manual thoroughly before installation, operation, or maintenance to ensure proper usage and to prevent personal injury or damage to the equipment.
The ANDELI CUT-65DS is a high-performance, non-HF pilot arc CNC plasma cutting machine designed for versatile applications. It features dual voltage compatibility (110V/220V), an intelligent ECO mode for energy saving, and a multi-zone real-time monitoring LED interface.
2. Safety Information
WARNING: ARC WELDING CAN BE HAZARDOUS. PROTECT YOURSELF AND OTHERS FROM POSSIBLE SERIOUS INJURY OR DEATH. KEEP CHILDREN AWAY. PACEMAKER WEARERS SHOULD CONSULT WITH THEIR DOCTOR BEFORE OPERATING.
Read and understand the following safety highlights. For additional safety information, it is strongly recommended you download free PDF of Standard ANSI Z49.1 from the American Welding Society.
CALIFORNIA PROPOSITION 65 WARNINGS:
- WARNING: Breathing diesel engine exhaust exposes you to chemicals known to the State of California to cause cancer and birth defects, or other reproductive harm. Always start and operate the engine in a well-ventilated area. If in an exposed area, vent the exhaust to the outside. Do not modify or tamper with the exhaust system. Do not idle the engine except as necessary.
- WARNING: This product, when used for welding or cutting, produces fumes or gases which contain chemicals known to the State of California to cause birth defects and, in some cases, cancer.
2.1. Electric Shock Can Kill
The electrode and work (or ground) circuits are electrically "hot" when the welder is on. Do not touch these "hot" parts with your bare skin or wet clothing. Wear dry, hole-free gloves to insulate hands. Insulate yourself from work and ground using dry insulation. Make certain the insulation is large enough to cover your full area of physical contact with work and ground.
In addition to normal safety precautions, if welding must be performed under electrically hazardous conditions (in damp locations or while wearing wet clothing; on metal structures such as floors, gratings or scaffolds; when in cramped positions such as sitting, kneeling or lying; if there is a high risk of unavoidable or accidental contact with the workpiece or ground) use appropriate equipment.
Always ensure the work cable makes a good electrical connection with the metal being welded. Ground the work or metal to be welded to a good electrical (earth) ground. Maintain the electrode stinger, work clamp, welding cable and welding machine in good, safe operating condition. Replace damaged insulation. Never dip the electrode in water for cooling. Never simultaneously touch electrically "hot" parts of electrode stingers connected to two welders because voltage between the two can be the total of the open circuit voltage of both welders.
Figure 2.1: Non-Touch Pilot Arc in operation, highlighting safety features.
2.2. Fumes and Gases Can Be Dangerous
Welding may produce fumes and gases hazardous to health. Avoid breathing these fumes and gases. When welding, keep your head out of the fume. Use enough ventilation and/or exhaust at the arc to keep fumes and gases away from the breathing zone. Do not weld in locations near chlorinated hydrocarbon vapors. Shielding gases can displace air and cause injury or death. Always use enough ventilation, especially in confined areas, to insure breathing air is safe.
2.3. Welding, Cutting, and Gouging Sparks Can Cause Fire or Explosion
Remove fire hazards from the welding area. If this is not possible, cover them to prevent welding sparks from starting a fire. Have a fire extinguisher readily available. Do not heat, cut, or weld tanks, drums, or containers until proper steps have been taken to insure that such procedures will not cause flammable or toxic vapors from substances inside. They can cause an explosion even though they have been "cleaned".
2.4. Arc Rays Can Burn
Use a shield with the proper filter and cover plates to protect your eyes from sparks and the rays of the arc when welding or observing open arc welding. Welding shield and filter lens should conform to ANSI Z87.1 standards. Use suitable clothing made from durable flame-resistant material to protect your skin and that of your helpers from the arc rays. Protect other nearby personnel with suitable, non-flammable screening and/or warn them not to watch the arc nor expose themselves to the arc rays or to hot spatter or metal.
2.5. Plasma Arc Can Injure
Keep your body away from the nozzle and plasma arc. Operate the pilot arc with caution. The pilot arc is capable of burning the operator, others, or even piercing safety clothing.
2.6. Cylinder May Explode If Damaged
Use only compressed gas cylinders containing the correct shielding gas for the process used and properly operating regulators designed for the gas and pressure used. All hoses, fittings, etc. should be suitable for the application and maintained in good condition. Always keep cylinders in an upright position securely chained to an undercarriage or fixed support. Locate cylinders away from areas where they may be struck or subjected to physical damage, and a safe distance from arc welding or cutting operations and any other source of heat, sparks, or flame. Never allow the electrode, electrode stinger, or any other electrically "hot" parts to touch a cylinder. Keep your head and face away from the cylinder valve outlet when opening the cylinder valve. Valve protection caps should always be in place and hand tight except when the cylinder is in use or connected for use.
3. Specifications
3.1. General Technical Parameters
| Parameter | AC110V 50Hz | AC220V 50Hz |
|---|---|---|
| Rated Input Power Supply | Single-phase | Single-phase |
| Rated Input Capacity (KVA) | 7.4 | 11.6 |
| Power Factor | 0.7 | |
| Rated Output (AV) | 45/96 | 65/100 |
| Rated Duty Cycle (%) | 60 | |
| No-load Voltage (V) | 300 | |
| Output current range (A) | 45 | 65 |
| Arc Ignition Mode | HF | |
| Post-flow Time (S) | 2-10 | |
| Gas Pressure Range (Psi) | 35~45 | 45-60 |
| Insulation Grade | F | |
| Cooling Mode | Air Cooling | |
| Enclosure Ingress Protection | IP21S | |
| Efficiency (%) | 85 | |
Figure 3.1: Detailed technical parameters and CE certification for the CUT-65DS.
3.2. Product Size and Weight
- Weight: 7.0 kg / 15.43 lbs
- Dimensions (L*W*H): 475 * 175 * 305 mm / 18.7 * 6.9 * 12 inches
Figure 3.2: Physical dimensions and weight of the plasma cutter, highlighting its portability.
3.3. Power Supply and Wiring Specifications
Power Cord Requirements:
- Standard Power Cord: Diameter: 3.3 mm² (AWG 12)
- Extension Cord Selection: If exceeding standard length, use the table below to ensure adequate wire gauge.
Critical Note: Inadequate wire gauge may cause voltage drop, resulting in unstable arc ignition, intermittent cutting performance, and reduced machine efficiency.
| Input Voltage | Phases | Length | Diameter |
|---|---|---|---|
| 110V/220V | 1PH | ≤15M (49INCH) | 10MM² (AWG 8) |
| 15~30M (49-98.5INCH) | 16MM² (AWG 5) | ||
| 30-45M (98.5-147.6INCH) | 25MM² (AWG 3) |
Generator Usage Guidelines:
Use fixed power sources whenever possible. Generator is not recommended. If generator operation is unavoidable, please strictly comply with specifications below:
| Generator Rating Power | Output Current | Performance |
|---|---|---|
| 10KW | 50A | Complete |
| 8KW | 45A | Limited |
| 6KW | 30A | Complete |
4. Packaging Details
The ANDELI CUT-65DS Plasma Cutter package includes the following components:
- AIR Plasma Cutter x1
- Ground Clamp x1
- User Manual x1
- Air Regulator Filter x1
- Gas Hose x1
- Gas Hose Connector x1
- Air Hose x1
- CNC Wire Connector (2Pins and 4Pins) x1
- Electrode x2
- Nozzle x2
- 110V/220V Power Adapter x1
- FPT40 Plasma Cutting Torch (13FT) x1
- Protective Cover x1
- Two-Point Bracket x1
- External Nozzle x2
- Hose Clamp x2
- Electrode x3 (additional)
- Nozzle x5 (additional)
Figure 4.1: The ANDELI CUT-65DS Plasma Cutter and its included accessories.
Figure 4.2: Detailed view of the package contents with numbered components.
5. Setup and Installation
Read all safety precautions before proceeding with installation.
5.1. Installation Environment Requirements
- Ventilation Clearance: Maintain ≥ 50 cm (20 in) clearance around all ventilation louvers.
- Prevent dust/metal particulates (>50 microns) from entering the system.
- Consequence of non-compliance: Overheating, automatic shutdown, and voided warranty.
- Compressed Air Specifications:
- 110V Operation: 35-45 PSI (2.4-3.1 bar)
- 220V Operation: 45-60 PSI (3.1-4.1 bar)
Critical Warnings:
- OIL CONTAMINATION: Hydrocarbon exposure causes plasma arc instability and irreversible torch damage.
- PRESSURE DEVIATION: Operating outside specified ranges may result in electrode/nozzle premature failure, kerf width inconsistency, and consumable costs increasing by 40-60%.
Stacking: The CUT-65DS cannot be stacked.
Tilting: The CUT-65DS must be placed on a stable, level surface so it will not topple over.
5.2. Installation of the Cutting Torch
To install the cutting torch, follow these steps:
- Disassemble the torch components: nozzle cup, nozzle, swirl ring, electrode, and torch handle.
- Ensure all components are clean and free of debris.
- Reassemble the torch in the correct order, ensuring all connections are secure.
Figure 5.1: Exploded view of the cutting torch components for assembly.
5.3. Installation of Air Pressure Compressor Filter Regulator
Connect the air compressor to the plasma cutter. The unit comes with a pre-installed air filter regulator.
Figure 5.2: The pre-installed air filter regulator on the plasma cutter.
Fitting Adaptation Procedure:
- Standard connection: NPT 1/4" male thread.
- For non-standard interfaces: replace with certified adapter fitting and Teflon sealing tape.
Moisture Management:
| Component | Action | Threshold |
|---|---|---|
| Pressure Regulator | Drain accumulated condensate | Daily / After 4 hr ops |
| Filter Bowl | Empty liquid | When visible 2/3 full |
Consequence: Otherwise, moisture will reduce cut quality.
5.4. Output Connections
Connecting Torch and Work Lead:
Connect the plasma torch and work lead to their respective ports on the front panel of the machine.
Connecting Work Clamp:
The work clamp must be securely connected to the workpiece. If the workpiece is painted or extremely dirty, it may be necessary to expose the bare metal in order to make a good electrical connection.
5.5. Gas Input Connection Options
- Standard Configuration: Pre-installed 10 mm quick-connect fitting.
- Optional Conversion: 1/4" NPT female adapter available as accessory P/N ADPT-NPT14.
5.6. CNC-Controlled System Integration
The CUT-65DS supports CNC integration for automated cutting operations.
Control Interfaces:
- 2-Pin Arc Voltage Output:
- Pin 1: -Arc Signal (Negative output)
- Pin 2: +Arc Signal (Positive output)
- Voltage Divider Settings (Rear Panel DIP Switch): Default: 20:1 ratio. Options: 30:1, 40:1, 50:1. To change voltage divider setting: Power OFF and disconnect before adjustment. Match ratio to CNC THC requirements.
- 4-Pin Control Interface:
- Pin 1 & Pin 2 Output: OK to Move signal. This is a normally open contact. When the contact is closed, the CNC track starts to work.
- Pin 3 & Pin 4: Torch Switch signal. When the contact is closed, the cutting torch starts to work. When the contact is open, the cutting torch stops working.
CNC Integration Warning: MANDATORY PRE-INSTALLATION CHECK
- Verify divided arc voltage setting matches CNC Torch Height Controller (THC) specifications.
- Requires qualified technician for PCB link reconfiguration (main board soldering).
Figure 5.3: The plasma cutter connected to CNC equipment for automated cutting.
6. Operating Instructions
6.1. Panel Functions of CUT-65DS
Figure 6.1: Front and rear panel overview with numbered components.
- Pilot arc (connect the pilot wire of torch)
- Torch Switch (connect the control of cutting torch)
- Gas-electric connector (Connect the cutting torch)
- Earth Clamp Connector
- Air Regulator Filter
- Power Cable
- Power Switch
- Arc voltage regulator
- 2 pins CNC interface
- 4 pins CNC interface
- Cooling Fan
- Air Pressure Adjustment Button (Rotate it towards "+" to increase pressure; rotate it towards "-" to decrease pressure.)
6.2. Multi-Zone Real-Time Monitoring LED Interface
The CUT-65DS features a 4.05'' oversized LED display with 3 dedicated display zones for critical parameters: PSI (gas pressure), voltage, and current.
Figure 6.2: The multi-zone real-time monitoring display showing PSI, voltage, and current.
Upon powering on, the digital display activates with the right panel showing the preset output current (20-65A), while the upper left window automatically detects and displays real-time input air pressure and the lower left window indicates the recognized input voltage (220V/110V). During normal operation, the green 'AC' power indicator remains illuminated, confirming proper electrical connection and system readiness for plasma cutting operations.
When the input voltage is detected as 110V, the blue light of the bottom right will light up to display the input voltage, while the digital display simultaneously shows the available current output range of 20-45A.
6.3. Setting Parameters and Adjusting Output Current
- Adjust the air pressure: Press the UNIT button to change the gas pressure display unit. Adjust the air compressor's output air flow and pressure to be adequate for the machine. Open the valve of the air compressor.
- Turn the Center Knob to adjust the amperage. Make sure cutting current is adequate to machine specifications according to the thickness of the cutting piece.
- Press the POST FLOW button to select post-flow time. And turn the Center Knob to adjust the post-flow time.
- Press the STEPS MODE button to select 2T or 4T mode.
6.4. 2T/4T Function
The 2T/4T automatic cutting function frees your hands for uninterrupted use.
- 2T: A semi-automatic cutting control. Suitable for flexible cutting.
- 4T: An automatic cutting control. Helps alleviate fatigue from prolonged operation.
Figure 6.3: Explanation of the 2T/4T cutting modes.
6.5. ECO Mode for Energy Saving
The intelligent ECO mode delivers 100% continuous cutting capacity at just 60% output power, easily meeting high-intensity non-stop operation demands. Perfect for thin plate cutting, it ensures high-quality processing with smooth and flat cuts, narrow kerf, and fast speed, reducing costs and bringing exceptional output with minimal effort.
Figure 6.4: The ECO energy saving mode in action, demonstrating continuous thin plate cutting.
6.6. Ready to Cut
Before you start to cut, make sure:
- The green power ON LED on the front of the power supply is illuminated.
- The voltage display corresponds to the actual input voltage.
- The output current (amperage) displayed on the front panel is correct, and the "A" LED is illuminated.
- The gas pressure displayed on the front panel is correct.
- None of the fault LEDs or CODE is illuminated.
WARNING: INSTANT-ON TORCHES - PLASMA ARC CAN CAUSE INJURY AND BURNS. The plasma arc ignites immediately when you pull the torch trigger. Make sure the power is OFF before changing consumables.
Trigger on the torch to activate the torch and let air go through. The pilot arc will come on and remain on for 5 seconds during which the cutting tip must come into contact with the workpiece. If the cutting tip does not come into contact with the workpiece within 5 seconds of the pilot arc start, the arc automatically stops (the post-flow air continues to run, cooling the plasma torch).
6.7. Notes for Cutting Operation
- It is recommended not to ignite the arc in the air if not necessary, as it will shorten the lifespan of the electrode and nozzle of the torch.
- It is recommended to initiate the cutting from the edge of the workpiece, unless penetration is needed.
- Ensure spatters fly from the bottom of the workpiece while cutting. If spatters fly from the top of the workpiece, it indicates that the workpiece cannot be fully cut because the cutting torch is moved too fast or the cutting current is too low.
- Keep the nozzle slightly touching the workpiece or keep a short distance between the nozzle and workpiece. If the torch is pressed against the workpiece, the nozzle may stick to the workpiece, and smooth cutting is unavailable.
- For cutting round workpiece or to meet precise cutting requirements, molding board or other assistant tools are needed.
- It is recommended to pull the cutting torch while cutting.
- Keep the nozzle of the cutting torch upright over the workpiece, and check if the arc is moving with the cutting line. If the space is not enough, don't bend the cable too much, step on or press upon the cable to avoid suffocating of gas flow. The cutting torch may be burned because the gas flow is too small. Keep the cutting cable away from edge tools.
- Clean up the spatters on the nozzle timely, for it will affect the cooling effect of the nozzle. Clean up the dust and spatters on the torch head after using every day to ensure good cooling effect.
6.8. Cutting Parameters Table (Approximate)
| Material | Cutting Thickness (mm) | Cutting Speed (m/min) @ 65A |
|---|---|---|
| Mild steel | 0.1 - 8 | 8 (for 1mm), 1.5 (for 3mm), 0.4 (for 6mm) |
| Galvanized steel | 0.1 - 8 | 8 (for 1mm), 1.5 (for 3mm), 0.4 (for 6mm) |
| Stainless steel | 0.1 - 8 | 8 (for 1mm), 1.5 (for 3mm), 0.4 (for 6mm) |
| Aluminum | 0.1 - 8 | 8 (for 1mm), 1.5 (for 3mm) |
| Brass | 0.1 - 0.75 | 0.75 (for 1mm) |
| Red copper | 0.1 - 0.75 | 0.75 (for 1mm) |
Figure 6.5: Visual comparison of cutting performance on different materials at 110V and 220V.
Video 6.1: Product demonstration showing the plasma cutter in action, cutting various materials and highlighting features like CNC cutting, gouging, and custom engraving.
7. Maintenance
7.1. Routine Maintenance
- Keep the cutting or gouging area and the area around the machine clean and free of combustible materials. No debris should be allowed to collect which could obstruct air flow to the machine.
- Every 6 months or so, the machine should be cleaned with a low-pressure airstream. Keeping the machine clean will result in cooler operation and higher reliability. Be sure to clean these areas: Printed circuit boards and heat sinks, Power switch.
CAUTION: When using a low-pressure air stream, wear appropriate eye protection.
- Examine the sheet metal case for dents or breakage. Repair the case as required. Keep the case in good condition to insure that high voltage parts are protected and correct spacings are maintained. All external sheet metal screws must be in place to insure case strength and electrical ground continuity.
- Regularly clean the compressor air inlet filter.
7.2. Maintain Torch Components
DANGER: Disconnect power cord and make sure Torch is completely cool before maintenance.
- Disassemble Torch.
- Inspect the Cutting Tip. Replace if interior is damaged, or if opening is enlarged or gouged. Clean inside as needed with steel wool (remove any pieces of steel wool afterwards).
- Inspect the Electrode. Replace if pitted 1/16" or more or if misshapen.
- Make sure all other internal torch components are undamaged, clean, and free of debris.
- Assemble Electrode just snug using the included wrench, but do not overtighten.
- Insert the Swirl Ring and Cutting Tip into the torch.
- Assemble the Retaining Cup tightly.
DO NOT USE WITH WORN COMPONENTS. USING WORN COMPONENTS WILL VOID THE WARRANTY AND DAMAGE THE PLASMA CUTTER.
7.3. Replacement of Electrode and Nozzle
When the phenomena below occur, the electrode and nozzle should be replaced. Otherwise, there will be strong arc in the nozzle, which will break down the electrode and the nozzle, or even burn the torch. Nozzles of different models are different, so ensure the nozzle is of the same model when replacing it.
- Electrode wear > 1.5mm
- Distortion of the nozzle
- Cutting speed declining, arc with green flame
- Difficult in arc ignition
- Irregular cut
7.4. Change Consumables
Thermal Detection Devices protect the machine from excessive operating temperatures. Excessive temperatures may be caused by a lack of cooling air or operating the machine beyond the duty cycle and output rating. If excessive operating temperatures should occur, the yellow thermal LED will light and the Detection Devices will prevent output voltage or current.
These Detection Devices are self-resetting once the machine cools sufficiently. If the thermostat shutdown was caused by excessive output or duty cycle and the fan is operating normally, the Power Switch may be left on and the reset should occur within a 15 minute period. If the fan is not turning or the air intake louvers were obstructed, then the power must be switched off and the fan problem or air obstruction must be corrected.
8. Troubleshooting
The abnormity indicator on the front panel would illuminate in case of any failures inside the cutting machine.
8.1. Malfunction Phenomena, Cause and Solution
| Malfunction Phenomena | Cause and Solution |
|---|---|
| The yellow light next to the input voltage is on (red light indicates undervoltage). | Multimeter with AC grade input voltage, input voltage is normal, shut down and restart to see if the machine can be normal. |
| When the machine's digital display reads "E-3" | Inspect whether the external pressure reduction valve is open and verify the internal solenoid valve's functionality. |
| The absence of arc maintenance and ignition in the machine | Open the machine shell, press the cutting gun to see if the electrode of the high-frequency board has sparks, if there is no spark, turn off the machine power supply and unplug the control wires on the high-frequency board, the multimeter clamps the gas-electricity interface and the grounding clamp connector, turn on the power supply and press the cutting gun to test the no-load voltage is normal. |
| The machine fails to power up | Confirm the normalcy of the input voltage, the functionality of the power switch, and scrutinize the machine's internal wiring for any signs of loosening. |
| The machine maintains an arc and ignites but cannot cut effectively. | Using a clamp meter set to the DC current range, clamp it onto the ground clamp and monitor the current. An absence of current might suggest an internal circuit issue or a failure of the reed switch tasked with current detection. Deformations in the bracket above the nozzle or excessive distance between the cutting tip and the workpiece can also prevent proper cutting. |
8.2. Error Codes and Solutions
| Error Code | Description and Solution |
|---|---|
| E-1 | Internal components damaged. The warning indicator light will light up and the air pressure display screen will display E-1. Restart the machine. |
| E-3 | Turned on without air pressure. The gas pressure display E-3. |
| E-5 | Operating temperature of the IGBT is too high. The gas pressure display E-5. Wait for cooling. |
9. User Tips
- This machine provides nice clean cuts and is easy to use, fast, and clean. It is suitable for use with small CNC machines.
- The CUT-65DS is compatible with CNC systems and includes a voltage divider for torch height control.
- For specific accessories like a straight torch, contact ANDELI support directly.
10. Warranty and Support
For support and service, please use the following contact information:
- Website: www.andelitools.com
- Support Email: support@andeligroup.com
- After-Sales Support (USA): +1 (949) 617-9002
- After-Sales Support (Hong Kong): +852 8480 7265
Service Centers:
- USA: LIPO INC (ATTN) D-100, 12 Hughes Irvine, CA 92618 USA
- Hong Kong: Workshop 60, 3/F, Block A East Sun Industrial Centre No. 16 Shing Yip Street Kwun Tong, Hong Kong
A detailed user manual in PDF format is available for download: ANDELI CUT-65DS User Manual (PDF)