AUTOPMALL Firmware Upgrade Configuration Cable

Contents

MiCODUS 2G Tracker Firmware Upgrade Cable User Manual

For Models: MV710, MV720, MV730, MV740, MV760, MV790

1. Product Overview

This document provides instructions for using the AUTOPMALL Firmware Upgrade Configuration Cable to update the firmware of specific MiCODUS 2G GPS trackers. This upgrade is crucial for resolving GPS-related functional anomalies, specifically the GPS Week Number Rollover (WNRO) issue affecting MediaTek MTK 2503D chips. The issue can cause GPS date stamps to reset to January 1st, 2006, and lead to unstable or intermittent positioning functionality.

The firmware upgrade ensures that all original device functions, including GLONASS positioning, remain unchanged and fully enabled. Additionally, it significantly improves the GPS signal reception performance of the device.

MiCODUS 2G Tracker Firmware Upgrade Cable
MiCODUS 2G Tracker Firmware Upgrade Cable

2. Applicable Models

This firmware upgrade applies exclusively to the following MiCODUS 2G device models:

  • MV710
  • MV720
  • MV730
  • MV740
  • MV760
  • MV790

These devices require manual firmware updates via the configuration cable as they do not support Over-the-Air (OTA) remote upgrades. There are no specific restrictions on device versions; any unit of the above models is eligible for this upgrade.

3. Required Tools and Materials

  • Computer: Running Windows 7 or later, with stable performance and free of viruses.
  • Serial Port Driver Software: CH340 driver (for serial communication).
  • Upgrade Software Package: Multiport_download_exe_v5.1624.00 (contains necessary programs).
  • Configuration Cable (Serial Cable): The cable provided with this product, used to connect the computer and the device. Ensure it is intact and undamaged.
  • Device Firmware Package: The specific firmware for your device model (e.g., MV710_MV790_241031A or MV720_MV730_250318A).
  • External Power Supply: To power the 2G tracker during the upgrade.

4. Firmware Upgrade Instructions

Follow these steps carefully to upgrade your MiCODUS 2G Tracker firmware:

4.1. Preparation

  1. Download Firmware and Tools:
    Download the firmware update file and upgrade tools from the official MiCODUS website: https://www.micodus.com/news/file
    Screenshot of MiCODUS firmware download page
    MiCODUS Firmware Download Page
    Screenshot of extracted firmware files
    Extracted Firmware Files in D: Drive
  2. Extract Files: Extract the downloaded upgrade files (driver, upgrade software, and firmware package) to a designated drive on your computer, for example, the D: drive.
  3. Install Serial Port Driver:
    Open the `CH340drive` folder from the extracted files. Double-click `CH341SER.exe` to install the driver. Follow the on-screen prompts. Disable any antivirus software during installation to prevent interference.
    USB end of the configuration cable
    USB end of the configuration cable
  4. Connect Cable to PC: Insert the USB end of the configuration cable into a USB port on your computer.
    USB end connected to PC
    Configuration cable connected to PC USB port
  5. Verify COM Port: Right-click 'My Computer' (or 'This PC'), select 'Manage'. In the 'Computer Management' window, navigate to 'System Tools' > 'Device Manager' > 'Ports (COM & LPT)'. Locate 'USB-SERIAL CH340 (COMX)' and note down the COM port number (e.g., COM3). This confirms the driver is installed correctly.

4.2. Using the Upgrade Software

  1. Open Upgrade Tool: Open the extracted `Multiport_download_exe_v5.1624.00.00` folder, navigate to the `output` folder, and double-click `MultiPortFlashDownloadProject.exe` to launch the upgrade software.
  2. Load Agent File: In the software interface, click the 'File' menu and select 'Open Download Agent File'. Navigate to the `output` folder and select `MTK_AllInOne_DA.bin`. Click 'Open'.
  3. Configure Options: Go to the 'Options' menu and ensure the following settings are checked:
    • Enable USB 1.1 to 2.0
    • Enable Long-Press Power Key Setting
    • Backup Nvram Partition
    • USB Meta Mode After One Station Download
  4. Load Firmware Package: In the software, find the 'Image Folder' option. Navigate to the folder containing the firmware package for your specific device model (e.g., `Firmware for MV710 MV720 MV730 MV740 MV790`), select it, and confirm.
  5. Select GPS Download Option: From the 'File' menu, select 'Scatter and Load'. In the pop-up window, check only the 'GPS' download item. Ensure all other items are unchecked. Then close the window.

4.3. Device Connection and Upgrade

  1. Connect Cable to Device: Connect the other end of the configuration cable to the corresponding port on your 2G device. This port is usually located next to the SIM card slot.
  2. Connect External Power: The device must be connected to an external power supply. Do NOT insert a SIM card into the device during the upgrade process.

    Video demonstrating cable connection to device and external power supply.
  3. Start Upgrade: In the upgrade software, locate the COM port number you recorded earlier (e.g., COM3). Click the 'Start' button corresponding to that COM port to begin the upgrade process.
  4. Complete Upgrade: The upgrade progress bar for the selected COM port will turn green and reach 100% when the upgrade is complete. Click the 'Stop All' button to finalize the process.

5. Troubleshooting and Precautions

  • Stable Connection: Ensure the configuration cable remains firmly connected to both the computer and the device throughout the upgrade. Forcibly disconnecting the device may damage its firmware.
  • Correct Firmware: Always use the firmware package that specifically matches your device model. Using an incorrect package can lead to upgrade failure or device damage.
  • Computer Stability: The computer used for the upgrade must remain stable. Avoid crashes or restarts. It is recommended to close all unnecessary programs to prevent interference.
  • Environment: Perform the upgrade in a dry and dust-free environment to prevent dust from affecting the cable connections.
  • "ERROR" Message: If an "ERROR" message appears during the upgrade, click the "Stop" button to halt the process. Recheck the cable connection, firmware package selection, and COM port. Resolve any identified issues before attempting the upgrade again.
  • Upgrade Failure: If the upgrade fails and the device does not start normally, do not attempt to disassemble the device yourself. Contact professional technical personnel for assistance.

6. Specifications

AttributeValue
Brand NameAUTOPMALL
Model NameFirmware Upgrade configuration Cable
FunctionFirmware Upgrading
Applicable DeviceMiCODUS MV710, MV720, MV730, MV740, MV760, MV790
Voltage12 V (for connected device)
GPS typeGPS Tracker (for connected device)
Screen SizeNo screen (for cable/device)
Battery Life1 To 4 Hours (for connected device)
GPS ModuleNo (for cable)
Item SizeNone
Out PowerW
OriginMainland China

7. User Tips

  • Always back up any important data from your device before performing a firmware upgrade, even though this specific upgrade has minimal impact on device data.
  • Keep the configuration cable and device in a clean, dry place to ensure optimal performance and longevity.
  • If you encounter any difficulties, refer to the official MiCODUS YouTube guide for visual assistance: https://www.youtube.com/watch?v=LvQqdkKDJJg

8. Support

For technical assistance or if your device fails to operate correctly after the upgrade, please contact professional technical personnel. Do not attempt to disassemble the device yourself.

A detailed user manual in PDF format is also available for reference.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.