1. Setup
1.1 Package Contents
Please check the contents of your package against the list below. If any items are missing or damaged, please contact your vendor.
Set 1 (No Memory Card)

Contents of Set 1 (No Memory Card) including the NanoVNA-H4 Plus host, USB-C cables, SMA RF cables, calibration kits (OPEN, SHORT, LOAD), SMA female-to-female connector, touch pen, and pick.
- NanoVNA-H4 PLUS Host x1
- USB Type-C cable x1
- 15cm SMA male to male TG316 RF cable x2
- SMA Male Calibration Kit OPEN x1
- SMA Male Calibration Kit Short Circuit x1
- SMA Male Calibration Kit LOAD x1
- SMA female to female connector x1
- Type-C to Type-C cable x1
- Touch Pen x1
- Pick x1
Set 2 (With 32GB Memory Card)

The 32GB memory card included in Set 2, for expanded data storage.
- All items from Set 1
- 32GB memory card x1
1.2 Initial Power On and Charging
The NanoVNA-H4 Plus comes with a built-in 5000mAh battery, providing extended operating time. Before first use, it is recommended to fully charge the device using the provided USB Type-C cable connected to a suitable power source (e.g., computer USB port or USB wall adapter).
1.3 SD Card Insertion
If your package includes an SD card, insert it into the designated SD card slot on the device. The SD card facilitates the storage of test data and allows for easy exporting of data for further analysis.
2. Operating Instructions
2.1 Device Overview and Interface
The NanoVNA-H4 Plus features an ergonomic design and a 4-inch IPS LCD resistive touch screen. Navigation and control are made convenient with a large knob and the touch screen functionality.

Overview of the PORTXVNSA NanoVNA-H4 Plus, highlighting its 50KHz-2.7GHz range, key measurement capabilities, and included accessories.

Close-up of the NanoVNA-H4 Plus, emphasizing its ergonomic design and the upgraded measurement range of 50KHz-2.7GHz with 401 scan points.

Detailed view of the NanoVNA-H4 Plus's 4-inch IPS resistive touch screen, highlighting its fast reading, sensitive touch, accurate color reproduction, and high contrast.
2.2 Basic Operation
The device's 4-inch IPS LCD display offers a wide viewing angle, accurate color restoration, high contrast, and uniform brightness for clear data visualization. Use the resistive touch screen or the large knob to navigate menus and adjust settings.
Video demonstrating the user interface and navigation of the PORTXVNSA NanoVNA-H4 Plus, showing how to select traces, markers, and adjust settings.
2.3 PC Control via Nano Saver
For advanced analysis and data management, the NanoVNA-H4 Plus can be connected to a PC via its Type-C port. Utilize the Nano Saver software, a multiplatform tool, to save Touchstone files, sweep frequency spans in segments to gain more than 401 data points, and display/analyze the resulting data on your computer.

NanoVNA-H4 Plus connected to a laptop via Type-C for PC control using Nano Saver software, illustrating its 5000mAh rechargeable battery.
2.4 Measurement Capabilities
The NanoVNA-H4 Plus offers a wide range of measurement functions, making it a versatile tool for RF analysis:
- Scanning antenna systems and cables
- SWR and impedance matching
- Measuring dual-band and triple-band duplexers
- Port isolation by frequency band
- Measuring insertion loss of filters
- Measuring 2.4 GHz Antennas
- Measuring Shortwave Antennas
- Cable Length Measurement

Demonstration of various measurement capabilities of the NanoVNA-H4 Plus, including 2.7 GHz extension, 2.4 GHz antenna measurement, shortwave antenna analysis, and cable length measurement.

Applications of the NanoVNA-H4 Plus for HAM radio and RF electronics hobbyists, illustrating its use in scanning antenna systems, SWR/impedance matching, duplexer measurement, port isolation, and filter insertion loss.
3. Maintenance
3.1 General Care
- Keep the device clean and free from dust and moisture.
- Avoid exposing the device to extreme temperatures or direct sunlight.
- Use a soft, dry cloth for cleaning the exterior. For the screen, use a screen-specific cleaning solution and a microfiber cloth.
- Do not use harsh chemicals or abrasive cleaners.
3.2 Battery Care
- To prolong battery life, avoid completely discharging the 5000mAh battery frequently.
- Store the device in a cool, dry place if not used for extended periods, ideally with the battery charged to around 50-70%.
- Use only the provided or a compatible USB Type-C cable for charging.
4. Troubleshooting
This section provides solutions to common issues you might encounter with your NanoVNA-H4 Plus.
4.1 Device Not Powering On
- Ensure the battery is sufficiently charged. Connect the device to a power source using the USB Type-C cable and allow it to charge for at least 30 minutes before attempting to power on again.
- Check the power button for proper engagement.
4.2 Screen Unresponsive or Inaccurate Touch
- Perform a touch screen calibration if available in the device settings.
- Ensure the screen is clean and free from debris or moisture.
- Use the provided touch pen for more precise interaction with the resistive touch screen.
4.3 Inaccurate Measurements
- Ensure proper calibration using the provided SMA Male Calibration Kit (OPEN, SHORT, LOAD) before taking measurements.
- Check all cable connections for tightness and proper seating.
- Verify that the measurement frequency range and scan points are correctly configured for your application.
5. Specifications
| Feature | Specification |
|---|---|
| Measurement Bandwidth / Frequency Range | 50KHz-2.7GHz |
| Dynamic Range | 80dB (50KHz-900MHz), 60dB (900MHz-1.5GHz), 50dB (1.5GHz-2.7GHz) |
| Reflection Coefficient (SWR) | <1.1 |
| Frequency Accuracy | <0.5 ppm |
| Frequency Stability | <2.5 ppm |
| Scan Points | 401 |
| Display | 4-inch IPS LCD, Resistive Touch Screen |
| Battery | Built-in 5000mAh rechargeable battery |
| Connectivity | USB Type-C, SD Card Slot |
| Product Size | 160x92x35mm |
| Battery Included | No (referring to external batteries, internal is included) |
| High-concerned chemical | None |
| Origin | Mainland China |
| Certification | None |
6. Warranty and Support
For any warranty claims, technical support, or service inquiries, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.
7. User Tips
- Firmware Upgrades: Regularly check the manufacturer's official website or community forums for firmware upgrades. Keeping your device's firmware up-to-date can improve performance, add new features, and fix bugs.
- Calibration Accuracy: Always perform a full calibration with the provided calibration kits (OPEN, SHORT, LOAD) before critical measurements to ensure the highest accuracy.
- Data Storage: Utilize the SD card feature to save your measurement data. This allows for easy transfer to a computer for detailed analysis and record-keeping.
- PC Software: Explore the capabilities of PC control software like Nano Saver for enhanced data visualization and analysis beyond the device's built-in display.