Estardyn ESP32-C3 2.4 TFT

Contents

ESP32-C3 Board with 2.4" TFT LCD Touch Screen User Manual

Model: ESP32-C3 2.4 TFT | Brand: Estardyn

1. Introduction

This manual provides detailed instructions for the Estardyn ESP32-C3 Board with a 2.4-inch TFT LCD Touch Screen. This high-performance IoT chip offers powerful computing, new wireless connectivity, and is designed for a wide range of applications including smart home devices and wearable technology.

The ESP32-C3F4 is a compact yet powerful IoT chip, featuring a 32-bit RISC-V single-core processor with a maximum clock speed of 160MHz. It efficiently handles complex IoT application logic and supports 802.11b/g/n (Wi-Fi 4) for 2.4GHz communication up to 150Mbps. Integrated Bluetooth 5.0 (BLE) enables long-distance, low-power device interconnection. The board includes 4MB Flash for program storage and 320KB SRAM for runtime memory, suitable for multi-tasking.

ESP32-C3 Board with 2.4 inch TFT LCD Touch Screen
Front and back view of the ESP32-C3 Board with 2.4-inch TFT display and touch function.

2. Specifications

Attribute Value
Brand Name Estardyn
Model Number ESP32-C3 2.4 TFT
Type TFT
Display Mode 240*320
Resolution 320x240
Origin Mainland China
Customization Yes
High-concerned chemical None

Package Dimensions:

  • Length: 10 cm
  • Width: 7 cm
  • Height: 2 cm
  • Weight: 0.052 kg

3. Setup and Pinout

The ESP32-C3 board is designed for easy integration into your projects. Below is a detailed diagram of the board components and a table explaining each pin's function.

ESP32-C3 Board Pinout Diagram
Detailed diagram of the ESP32-C3 board showing numbered components and pin labels.

Board Components and Pin Functions:

Serial Number PCB Symbol / Function Meaning
15V5V power supply
2GNDGround
33.3V3.3V power supply
4TXOUART0_TX, GPIO 21
5RXOUART0_RX, GPIO 20
6GNDGround
7LCD display interface (White dots represent pin 1)GND: Power Ground
SDA: Data/Command Selection, GPIO 10
CS: SPI chip select signal, connected to GND
SCK: SPI clock, GPIO 6
SDI: SPI data (MOSI), GPIO 7
RESET: LCD reset, GPIO 8
VCC: Logic power supply, 3.3V power supply
GND: Power Ground
The backlight anode is connected to the 3.3V power supply through a current-limiting resistor.
LEDK: Backlight negative terminal, controlled by GPIO 0, with high level as the on signal.
8LCD touch interface (White dots represent pin 1)TP VDD: Touch power supply, 3.3V power supply
TP INT: Touch interrupt, GPIO 9
TP SDA: Touch IIC data, GPIO 4
TP SCL: Touch IIC clock, GPIO 3
TP RST: Touch reset, GPIO 2
GND: Power Ground
9GNDLED indicator light: GPIO_1 low voltage state lights the light up.
Power indicator light, always on when powered.
10BOOTPress the BOOT download mode button, hold it down, and then start the ESP32 to enter download mode.
11ResetReset button.
12ESP32-C3F4 main controllerThe main microcontroller unit.
13WiFi + Bluetooth PCB board built-in antennaIntegrated antenna for wireless communication.
14SD card interfaceSlot for SD card expansion.

Initial Connection:

  1. Connect the ESP32-C3 board to your computer using a Micro USB cable.
  2. Ensure the necessary drivers for the ESP32-C3 are installed on your operating system.
  3. The board should be recognized as a serial port.

4. Operating Instructions

Programming Environment:

This board is compatible with popular development environments such as Arduino IDE and MicroPython. You will need to install the ESP32 board support package for your chosen environment.

Uploading Code:

  1. Open your preferred IDE (e.g., Arduino IDE).
  2. Select the correct board model (ESP32-C3 Dev Module) and serial port from the Tools menu.
  3. To upload new firmware, you may need to press and hold the BOOT button (10) while pressing and releasing the Reset button (11), then release the BOOT button to enter download mode.
  4. Compile and upload your code.

Using the TFT Display and Touch Function:

The 2.4-inch TFT display uses the ST7789 driver and communicates via SPI. The touch function is integrated. Refer to the pinout table (Section 3) for specific GPIOs connected to the LCD and touch interfaces. Libraries such as Adafruit GFX and Adafruit ST7789 for Arduino, or relevant MicroPython modules, can be used to control the display and read touch input.

5. Maintenance

  • Keep the board clean and free from dust and moisture.
  • Avoid exposing the board to extreme temperatures or direct sunlight.
  • Handle the board by its edges to prevent damage to components or static discharge.
  • Ensure proper ventilation when the board is in operation, especially if enclosed.

6. Troubleshooting

Common Issues and Solutions:

  • Board not recognized by computer: Ensure USB cable is functional and drivers are correctly installed. Try a different USB port or cable.
  • Code upload failure: Verify correct board and port selection in IDE. Ensure the board is in download mode (refer to Operating Instructions). Check for compilation errors in your code.
  • Display not working: Check power connections (3.3V, GND) and SPI connections (SDA, SCK, SDI, CS, RESET). Ensure backlight (LEDK) is properly controlled. Verify display initialization code.
  • Touch screen unresponsive: Check touch interface connections (TP VDD, TP INT, TP SDA, TP SCL, TP RST, GND). Ensure touch library is correctly initialized and configured for the specific GPIOs.

7. User Tips

  • Configuration Files: When setting up the board, especially for display and touch, ensure you have the correct user_setup or configuration files for your chosen library (e.g., TFT_eSPI for Arduino). Incorrect pin definitions are a common cause of display issues.
  • Power Supply: While the board can be powered via USB, for stable operation, especially with peripherals, consider using a dedicated 5V power supply connected to the 5V pin if your project draws significant current.
  • Community Support: The ESP32 community is vast. If you encounter specific programming challenges, online forums and documentation for ESP32-C3, ST7789, and your chosen IDE (Arduino/MicroPython) are excellent resources.

8. Warranty and Support

For technical support, programming examples, or further assistance, please refer to the manufacturer's official website or contact your retailer. Keep your purchase receipt for any warranty claims.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.