ROBORE U18F

Contents

ROBORE U18F Foldable Treadmill User Manual

Model: U18F

Introduction

This manual provides essential information for the safe and effective use, assembly, operation, maintenance, and troubleshooting of your ROBORE U18F Foldable Treadmill. Please read this manual thoroughly before operating the equipment and retain it for future reference.

The ROBORE U18F is an upgraded version of the ROBORE CW1F, designed for home and office use, offering a compact and versatile fitness solution.

Important Precautions

Your safety is paramount. Please read and adhere to all instructions and warnings.

  • Before starting any workout program, consult your doctor. This is especially important for individuals over 35, those with health problems, and pregnant women.
  • Keep the equipment in an enclosed area, away from dust or humidity. Do not store it in a garage, indoor backyard, or near water. Humidity, dust, and water can cause malfunction and void the warranty.
  • Place the unit on a flat surface. Uneven surfaces can affect proper functioning. Some models may include levelers or leveling threads behind the legs; refer to the manual for your specific unit.
  • The unit must be placed in a well-ventilated area. Avoid using it in areas with sprays or oxygen dispensers, as this can affect air quality and cause accidents.
  • Keep children younger than 12 years old and pets away from the equipment. Maintain a safe distance.
  • Refer to this manual for the maximum weight capacity. Exceeding this weight can lead to malfunction and will not be covered by the warranty.
  • If your equipment is working through a power supply: ensure the power cord and plug are in good condition. Connect only to a grounded circuit to prevent damage to the equipment or property. Keep power cords away from hot surfaces.
  • If it is a battery-powered unit: ensure batteries are sufficiently charged for the display to function fully.
  • If your unit works with an electric supply: check the speed it can reach and your security. Adjust the speed gradually to avoid sudden changes.
  • Never leave the machine unattended while it is operating.
  • Regularly check and tighten all screws, as vibrations can cause them to loosen. Damages due to lack of maintenance are not covered by the warranty.
  • Two people are recommended to remove the unit from its packaging to prevent damage, which would not be covered by the warranty.
  • Do not let any objects fall into the grooves of the treadmill.
  • If the unit works through a power cord: unplug the power cord before cleaning, after workouts, and before performing any maintenance.
  • If you experience pain or dizziness during training, stop immediately.
  • Preserve the original packaging, protections, manual, and components during the warranty period.
  • This electronic product must be recycled according to local regulations and should not be disposed of in municipal rubbish bins. Contact your local council for recycling information.

Product Features

The ROBORE U18F is a 2-in-1 walking pad designed for versatility and convenience. It features a foldable handle bar, allowing it to be used as a traditional treadmill or folded down for under-desk walking. Key features include:

  • 15% Adjustable Incline: Simulates uphill running for enhanced calorie burn and cardiovascular benefits.
  • Triple Shock Absorption System: Comprising a 7-layer composite running belt, 8 built-in shock absorbers, and 2 external mats for joint protection and comfortable use.
  • Upgraded Quiet Motor: A 2.5HP brushless motor operates at less than 45 dB, ensuring quiet workouts.
  • Foldable Design: Folds to a thickness of 9 cm for easy storage and features built-in wheels for mobility.
  • No Assembly Needed: Ready to use out of the box.
  • Data Tracking: LED display tracks time, speed, distance, and calories.
  • Remote Control: For convenient speed and mode adjustments.
  • Phone Holder: Integrated for entertainment or productivity during workouts.

Parts List

The following components are included with your ROBORE U18F Treadmill. The armrest may require fixing upon initial setup.

Diagram showing the main body of the treadmill, phone holder, armrest, display, fixed knob, running belt, foot pad, and end caps.

Figure 1: Product Features and Components

No.ItemQuantity
1Main Body1
2Hex Wrench1
3Spanner1
4Remote Control1
5Fixing Knob2
6Fold-able Footrests2
7Silicone Boost2
8M4x16 Screws2
9M8x30 Hex Bolt2
10Lock Nut M82
11Phone Holder1
12User's Manual1

Specifications

AttributeValue
Brand NameROBORE
Model NumberU18F
ApplicationHome Use Treadmill
Type of sportsCardio Training
OriginMainland China
Input Voltage220-240V
Frequency50 HZ
FunctionWalking/Jogging
Speed Range1-10 KM/H (0.6-6.2 MPH)
Maximum Incline15% (simulates hill climbs)
Manual Incline Levels2% / 10% / 15%
Motor2.5HP
Noise Level<45 dB
Running Belt Dimensions37" × 15.5" (92.5 × 39 cm)
Running Belt Length80-120cm
Running Belt Width30-50cm
Max Load300 lbs (136kg)
FoldableYes
With SpeakersNo
Bluetooth ConnectionNo
ScreenNo (LED Display for data tracking)
Control MethodRemote control with storage box
Data TrackingTime, Speed, Distance, Calories
Product Weight14.9kg
Product Size (Unfolded)103.6 × 52.6 × 95 cm
Package Weight17.4kg
Package Size113.5 × 56 × 10.3 cm

The treadmill folds down to 9 cm thickness, making storage effortless. Built-in wheels facilitate quick and easy movement between rooms.

Setup

Unpacking and Initial Placement

  • It is recommended that two people unbox and move the treadmill to prevent damage.
  • Place the treadmill on a flat, stable surface in a well-ventilated area. Ensure there is sufficient clear space around the unit for safe operation.
  • The ROBORE U18F is designed for minimal assembly and is largely ready out of the box.

Handle Bar and Phone Holder Installation

The handle bar is foldable. To secure it in the upright position, use the provided fixing knobs. The phone holder attaches to the top of the handle bar.

A person installing the phone holder onto the treadmill's handle bar.

Figure 2: Attaching the Phone Holder

A person tightening a knob on the treadmill handle bar.

Figure 3: Securing the Handle Bar with a Knob

Manual Incline Adjustment

The treadmill is equipped with two levels of manual incline adjustment (2%, 10%, 15%). To adjust the incline, use the M8x30 screws and M8 nuts to fix the folding foot pedals on the treadmill platform. Ensure the support feet are properly adjusted to avoid injuries.

Diagram showing how to install the manual slope adjustment foot pedals using M8x30 screws and M8 nuts.

Figure 4: Manual Slope Installation

Diagram illustrating how to adjust the incline by placing the support leg into the boost for higher incline, and how to rotate to adjust the height of the rear guard.

Figure 5: Incline Adjustment and Rear Guard Height Adjustment

  • The height-increasing foot pads should only be used after the support feet have been fully extended.
  • If the rear cover touches the ground, rotate to adjust the height of the rear foot pads to prevent scraping.

Operating Instructions

Remote Control Operation

The treadmill is controlled via a remote control. Ensure batteries are installed in the remote control (2x AAA batteries, not included).

A person inserting AAA batteries into the remote control for the treadmill.

Figure 6: Installing Batteries in the Remote Control

Diagram of the remote control with buttons labeled: Speed +, Mode, Start/Stop, Speed -.

Figure 7: Remote Control Layout

  1. Step 1: Turn on the power switch of the treadmill.
  2. Step 2: In standby mode, press the "M" (Mode) key to enter three countdown modes: Time, Distance, and Calorie. During mode selection, the indicator light for the current mode will remain on. Select your desired mode, then use the "+" and "-" keys to increase or decrease the countdown value.
  3. Step 3: After setting the countdown value, press "ON/OFF" to start the treadmill.
  4. Step 4: To exit the countdown function or stop the treadmill, press "ON/OFF" again.

The treadmill's speed can be adjusted from 1 KM/H to 10 KM/H (0.6 to 6.2 MPH).

Video 1: Demonstration of Treadmill Setup and Operation

Running Belt Corrections

Centering the Running Belt

If the running belt is off-center to the left or right, or if you hear a rattling noise, adjust it to the correct position.

Diagram showing how to adjust the running belt if it's shifted to the left or right. It indicates removing covers and adjusting screws to center the belt.

Figure 8: Running Belt Adjustment for Centering

Procedure:

  1. Remove the covers before adjustment.
  2. Ensure the belt is centered before use. Refer to the instructions or contact customer support if needed.

Tightening a Slipping Running Belt

If the running belt slips during use, it may need to be tightened.

  1. Use a 5mm wrench to turn both side bolts 1/4 clockwise.
  2. Repeat this procedure until the belt is properly tightened and no longer slips.

Caution:

  • Heavy pedaling may cause the treadmill to shut down due to overload protection. This is not a machine failure.
  • Current and voltage overload may also cause shutdown.
  • Individual running habits (e.g., how hard the left or right foot treads) can cause the running belt to shift slightly over time.

Maintenance

Lubrication Instruction (for normal belt only)

Proper lubrication is crucial for the longevity and smooth operation of your treadmill. The treadmill is pre-oiled for immediate use, and the included 30ml oil should last approximately one year under normal circumstances.

A person applying lubricant under the running belt of the treadmill.

Figure 9: Applying Lubricant to the Running Belt

Usage FrequencyMaintenance Frequency
<3 Hours/WeekEvery 2 Months
4-7 Hours/WeekEvery 1 Month
>8 Hours/WeekEvery 2 Weeks

Application Steps:

  1. Turn off the machine and unplug it.
  2. Lift the running belt and apply approximately 2.5ml of oil directly onto the board underneath the belt.
  3. After applying oil, start the machine and set it to the highest speed for a few minutes. This will help spread the oil evenly between the running belt and the board.
  4. A good indicator of sufficient lubrication is when you touch the middle of the back of the running belt with your hand and it feels slightly wet with oil.

For a visual guide, scan the QR code below for a lubricant instruction video.

QR code linking to a lubricant instruction video.

Figure 10: QR Code for Lubricant Instruction Video

Troubleshooting

If you encounter any issues with your treadmill, refer to the table below for common error codes and their solutions.

NO.Error CodeDescriptionMaintenance
1E02Hall detection error1. Inspect Hall terminal
2. Replace motor
3. Replace lower control
2E03Overcurrent error1. Replace lower control
3E04Overvoltage error1. Inspect external mains input
2. Replace lower control
4E05Undervoltage error1. Inspect external mains input
2. Replace lower control
5E06Overload error1. Inspect if running belt resistance is abnormal
2. Replace motor
3. Replace lower control
6E08Lower control overheat error1. Inspect if running belt resistance is abnormal
2. Replace lower control
7E11UVW three wires open circuit error simultaneously1. Inspect if motor wires are abnormal
2. Replace motor
3. Replace lower control.
8E13Communication failure error1. Inspect if communication wires are abnormal
2. Replace lower control
3. Replace upper display

User Tips

  • The treadmill is compact and foldable, making it ideal for small living spaces or offices.
  • Its quiet operation is beneficial for use in shared environments or when working from home.
  • The 15% incline feature can significantly increase workout intensity without requiring longer exercise durations.
  • The built-in wheels make it easy to move and store the treadmill under furniture like a sofa when not in use.
  • While suitable for walking and light jogging, users over 180 cm (6 ft) may find the running belt length slightly short for comfortable running.
  • Always ensure all screws are tightened regularly to maintain stability and prevent loosening due to vibrations.

Warranty and Customer Support

1 Year Warranty

Your ROBORE U18F treadmill comes with a one-year warranty covering parts replacement.

To access warranty services, you must retain your purchase receipt.

Customer Support

For any issues or inquiries, please contact our customer support team. We are committed to providing 100% satisfaction.

  • Email Support: service_sports@163.com
  • Service Availability: 7*24 online customer service.
  • Maintenance Service: Free maintenance tools (including lubricants and remote control) are offered for orders within 6 months.

When contacting support, please provide your Order ID and a detailed description of the product problem, including attached pictures or videos if necessary.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.